Lina Klinge
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lina Klinge has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Carsten Siemers
Institute for Materials Science, TU Braunschweig, Braunschweig, Germany
2 shared publications- Christopher Spiegel
Department of Orthopaedics and Traumatology, Medical University of Innsbruck, Innsbruck, Austria
2 shared publications Peter Groche
Institute for Production Engineering and Forming Machines, TU Darmstadt, Darmstadt, Germany
2 shared publicationsC. Jahnke
TU Braunschweig – Institute for Materials Science
1 shared publicationC. Siemers
TU Braunschweig – Institute for Materials Science
1 shared publication- Carsten Siemers
Technische Universität Braunschweig
1 shared publication
Latest Publications
- Open Access
- 5 February 2025
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 58, 47-61
Nanostructuring of the titanium alloy Ti-13Nb-13Zr (NanoTNZ) for osteosynthesis implants by continuous multidirectional swaging
- 5 February 2025
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 58, 47-61
Open AccessNanostructuring of the titanium alloy Ti-13Nb-13Zr (NanoTNZ) for osteosynthesis implants by continuous multidirectional swaging
- Open Access
- 24 August 2023
- Published by Frontiers Media SA in Frontiers in Bioengineering and Biotechnology
- Vol. 11, 1255947
Nanostructured Ti-13Nb-13Zr alloy for implant application—material scientific, technological, and biological aspects
In dentistry, the most commonly used implant materials are CP-Titanium Grade 4 and Ti-6Al-4V ELI, possessing comparably high Young’s modulus (>100 GPa). In the present study, the second-generation titanium alloy Ti-13Nb-13Zr is investigated with respect to the production of advanced dental implant systems. This should be achieved by the fabrication of long semi-finished bars with high strength and sufficient ductility to allow the automated production of small implants at low Young’s modulus (<80 GPa) to minimize stress shielding, bone resorption, and gap formation between the bone and implant. In addition, bacterial colonization is to be reduced, and bone adhesion is to be enhanced by adjusting the microstructure. To do so, a dedicated thermo-mechanical treatment for Ti-13Nb-13Zr has been developed. This includes the adaption of equal channel angular swaging, a modern process of severe plastic deformation to continuously manufacture nanostructured materials, to Ti-13Nb-13Zr and short-time recrystallization and ageing treatments. In particular, two-pass equal channel angular swaging at a deformation temperature of 150°C and a counterpressure of 8 MPa has successfully been used to avoid shear band formation during deformation and to produce long Ti-13Nb-13Zr bars of 8 mm diameter. During recrystallization treatment at 700°C for 10 min followed by water quenching, a sub-micron-size primary α-phase in a matrix of α″-phase was developed. Subsequent ageing at 500°C for 1 h leads to martensite decomposition and, thus, to a homogeneously nanostructured microstructure of α- and β-phase with substructures smaller than 200 nm. The resulting mechanical properties, especially the ultimate tensile strength of more than 990 MPa, fulfill the requirements of ASTM F1713 at Young’s modulus of 73 GPa. Biological investigations show promising results in reducing bacterial biofilm formation and increased cell proliferation of osteoblasts compared to CP-Titanium Grade 4 and Ti-6Al-4V ELI, especially, if etched surfaces are applied.
- 24 August 2023
- Published by Frontiers Media SA in Frontiers in Bioengineering and Biotechnology
- Vol. 11, 1255947
Open AccessNanostructured Ti-13Nb-13Zr alloy for implant application—material scientific, technological, and biological aspects
In dentistry, the most commonly used implant materials are CP-Titanium Grade 4 and Ti-6Al-4V ELI, possessing comparably high Young’s modulus (>100 GPa). In the present study, the second-generation titanium alloy Ti-13Nb-13Zr is investigated with respect to the production of advanced dental implant systems. This should be achieved by the fabrication of long semi-finished bars with high strength and sufficient ductility to allow the automated production of small implants at low Young’s modulus (<80 GPa) to minimize stress shielding, bone resorption, and gap formation between the bone and implant. In addition, bacterial colonization is to be reduced, and bone adhesion is to be enhanced by adjusting the microstructure. To do so, a dedicated thermo-mechanical treatment for Ti-13Nb-13Zr has been developed. This includes the adaption of equal channel angular swaging, a modern process of severe plastic deformation to continuously manufacture nanostructured materials, to Ti-13Nb-13Zr and short-time recrystallization and ageing treatments. In particular, two-pass equal channel angular swaging at a deformation temperature of 150°C and a counterpressure of 8 MPa has successfully been used to avoid shear band formation during deformation and to produce long Ti-13Nb-13Zr bars of 8 mm diameter. During recrystallization treatment at 700°C for 10 min followed by water quenching, a sub-micron-size primary α-phase in a matrix of α″-phase was developed. Subsequent ageing at 500°C for 1 h leads to martensite decomposition and, thus, to a homogeneously nanostructured microstructure of α- and β-phase with substructures smaller than 200 nm. The resulting mechanical properties, especially the ultimate tensile strength of more than 990 MPa, fulfill the requirements of ASTM F1713 at Young’s modulus of 73 GPa. Biological investigations show promising results in reducing bacterial biofilm formation and increased cell proliferation of osteoblasts compared to CP-Titanium Grade 4 and Ti-6Al-4V ELI, especially, if etched surfaces are applied.
- 6 January 2023
- Published by Springer Nature
- p. 359-368
High-Strength, Low-Modulus Nanostructured: Ti 13Nb 13Zr Alloy
- 6 January 2023
- Published by Springer Nature
- p. 359-368
High-Strength, Low-Modulus Nanostructured: Ti 13Nb 13Zr Alloy
- Open Access
- 24 May 2022
- Published by Springer Nature in Journal of Materials Research
- Vol. 37 (16) , 2581-2588
Nanostructured Ti–13Nb–13Zr for dental implant applications produced by severe plastic deformation
Nanostructured titanium plays an important role in biomedical applications, especially in dentistry, as the nanostructured surface promotes bone cell growth and simultaneously prevents bacterial colonization. Nanostructured microstructures can be obtained through Severe Plastic Deformation processes. In this paper, thermomechanical processing via Equal Channel Angular Swaging for the continuous production of nanocrystalline Ti–13Nb–13Zr (TNZ) is investigated with respect to applications in dental implantology. TNZ is a second-generation β-rich (α + β) medical alloy which can consist of the three phases α- and β-phase as well as αʺ-martensite. The αʺ-martensite has a very low Young’s modulus and a comparably low strength with high ductility allowing metal forming even at low temperatures. By adjusting different phase volume fractions, a wide range of mechanical properties can be realized, especially Young’s modulus between 50 and 90 GPa at a yield strength exceeding 950 MPa making it an ideal material for dental implants and abutments. Graphical abstract
- 24 May 2022
- Published by Springer Nature in Journal of Materials Research
- Vol. 37 (16) , 2581-2588
Open AccessNanostructured Ti–13Nb–13Zr for dental implant applications produced by severe plastic deformation
Nanostructured titanium plays an important role in biomedical applications, especially in dentistry, as the nanostructured surface promotes bone cell growth and simultaneously prevents bacterial colonization. Nanostructured microstructures can be obtained through Severe Plastic Deformation processes. In this paper, thermomechanical processing via Equal Channel Angular Swaging for the continuous production of nanocrystalline Ti–13Nb–13Zr (TNZ) is investigated with respect to applications in dental implantology. TNZ is a second-generation β-rich (α + β) medical alloy which can consist of the three phases α- and β-phase as well as αʺ-martensite. The αʺ-martensite has a very low Young’s modulus and a comparably low strength with high ductility allowing metal forming even at low temperatures. By adjusting different phase volume fractions, a wide range of mechanical properties can be realized, especially Young’s modulus between 50 and 90 GPa at a yield strength exceeding 950 MPa making it an ideal material for dental implants and abutments. Graphical abstract