Mamadamon Abdullo
Mamadamon Abdullo has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Valentyna Verkholantseva
Tavria State Agrotechnological University
2 shared publications A B Tashripov
Tajik Technical University named after M S Osimi, 11, academicians of the Radjabovs, Dushanbe 734042, The Republic of Tajikistan
1 shared publicationAbdunabi Abduraufovich Kosimov
1 shared publication- Ahmadjon Rahmonzoda1 shared publication
- Akhmad M. Umirzokov
Tajik Technical University named after academician M.S. Osimi
1 shared publication F I Jobirov
Tajik Technical University named after M S Osimi, 11, academicians of the Radjabovs, Dushanbe 734042, The Republic of Tajikistan
1 shared publication
Latest Publications
- Open Access
- 15 October 2026
- Published by Institute of Economics and Demography of the National Academy of Sciences of Tajikistan in Economy of Tajikistan
- Vol. 3 (3) , 12-22
VALUE OF A STATISTICAL LIFE IN THE ECONOMIC APPRAISAL OF ROAD SAFETY MEASURES IN THE REPUBLIC OF TAJIKISTAN
The monetary value assigned to a prevented road fatality drives the outcome of any cost-benefit appraisal of road safety measures, yet no approved value exists for the Republic of Tajikistan. The paper compares the human capital method, the iRAP rule of thumb, the transfer function of Wijnen et al., and the procedures of Robinson et al. and the OECD, using World Bank macroeconomic indicators for 2024–2025 and departmental statistics of the State Automobile Inspectorate of the Ministry of Internal Affairs for 2016–2025. Estimates based on income at market exchange rates range from USD 87 to 95 thousand per prevented fatality, whereas purchasing-power-parity estimates range from USD 0.23 to 1.13 million; only the former are consistent with an independent estimate of crash losses as a share of GDP. A reference value of USD 91 thousand (2024 prices) is proposed, indexed to gross national income per capita, which yields approximately USD 115 thousand for 2025. Decomposition of annual losses shows that the completeness of casualty recording changes the result fivefold (0.67–3.41 % of GDP), while the two recommended valuation methods differ by no more than 9 %. Over the decade, the number of deaths per 100 crashes rose by half, shifting the economic priority towards measures that reduce crash severity.
- 15 October 2026
- Published by Institute of Economics and Demography of the National Academy of Sciences of Tajikistan in Economy of Tajikistan
- Vol. 3 (3) , 12-22
Open AccessVALUE OF A STATISTICAL LIFE IN THE ECONOMIC APPRAISAL OF ROAD SAFETY MEASURES IN THE REPUBLIC OF TAJIKISTAN
The monetary value assigned to a prevented road fatality drives the outcome of any cost-benefit appraisal of road safety measures, yet no approved value exists for the Republic of Tajikistan. The paper compares the human capital method, the iRAP rule of thumb, the transfer function of Wijnen et al., and the procedures of Robinson et al. and the OECD, using World Bank macroeconomic indicators for 2024–2025 and departmental statistics of the State Automobile Inspectorate of the Ministry of Internal Affairs for 2016–2025. Estimates based on income at market exchange rates range from USD 87 to 95 thousand per prevented fatality, whereas purchasing-power-parity estimates range from USD 0.23 to 1.13 million; only the former are consistent with an independent estimate of crash losses as a share of GDP. A reference value of USD 91 thousand (2024 prices) is proposed, indexed to gross national income per capita, which yields approximately USD 115 thousand for 2025. Decomposition of annual losses shows that the completeness of casualty recording changes the result fivefold (0.67–3.41 % of GDP), while the two recommended valuation methods differ by no more than 9 %. Over the decade, the number of deaths per 100 crashes rose by half, shifting the economic priority towards measures that reduce crash severity.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in “Polytechnic Bulletin” series “Technology and Society”
- Vol. 15 (3)
EFFECT OF ALTITUDE ON EXHAUST GAS COMPOSITION OF A PETROL HYBRID PASSENGER CAR
The paper examines how the exhaust composition of a petrol hybrid passenger car changes as it climbs a mountain road. On 22 September 2026 a Lexus RX 450h (2015) was tested at six stations between 801 and 2615 m above sea level along the Dushanbe – Istiqlol tunnel road, where ambient pressure fell from 92.3 to 74.6 kPa. CO, HC, NOx and CO2 were measured with an Avtotest gas analyser at idle and at elevated crankshaft speed, six readings per series (72 in total). Data were processed with Student's t-distribution (P = 0.95); the altitude effect was assessed by linear regression and one-way ANOVA. Hydrocarbon concentration rose from 15.2 to 32.3 ppm at idle and from 14.5 to 32.7 ppm at elevated speed, i.e. by about 9.4–9.7 ppm per 1000 m (R2 = 0.95–0.98). Nitrogen oxides fell by 83–89 % and the CO2 volume fraction by 8–14 %. No consistent altitude dependence was found for CO, whose mean values stayed at or below 0.18 %. The relationships obtained can support the adjustment of exhaust inspection procedures for vehicles operated in the mountain regions of Tajikistan.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in “Polytechnic Bulletin” series “Technology and Society”
- Vol. 15 (3)
EFFECT OF ALTITUDE ON EXHAUST GAS COMPOSITION OF A PETROL HYBRID PASSENGER CAR
The paper examines how the exhaust composition of a petrol hybrid passenger car changes as it climbs a mountain road. On 22 September 2026 a Lexus RX 450h (2015) was tested at six stations between 801 and 2615 m above sea level along the Dushanbe – Istiqlol tunnel road, where ambient pressure fell from 92.3 to 74.6 kPa. CO, HC, NOx and CO2 were measured with an Avtotest gas analyser at idle and at elevated crankshaft speed, six readings per series (72 in total). Data were processed with Student's t-distribution (P = 0.95); the altitude effect was assessed by linear regression and one-way ANOVA. Hydrocarbon concentration rose from 15.2 to 32.3 ppm at idle and from 14.5 to 32.7 ppm at elevated speed, i.e. by about 9.4–9.7 ppm per 1000 m (R2 = 0.95–0.98). Nitrogen oxides fell by 83–89 % and the CO2 volume fraction by 8–14 %. No consistent altitude dependence was found for CO, whose mean values stayed at or below 0.18 %. The relationships obtained can support the adjustment of exhaust inspection procedures for vehicles operated in the mountain regions of Tajikistan.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in “Polytechnic Bulletin” series “Technology and Society”
- Vol. 15 (3)
CLIMATE CHANGE ADAPTATION OF THE TRANSPORT SECTOR OF THE REPUBLIC OF TAJIKISTAN: VULNERABILITY ASSESSMENT, INSTITUTIONAL FRAMEWORK AND IMPLEMENTATION PRACTICE
Mountains cover ninety-three percent of Tajikistan. That single figure shapes the country's logistics: the road network absorbs climate stress with almost no modal alternative behind it. This article assesses the vulnerability of the transport sector and examines the adaptation governance system now taking shape. The design is mixed-method. Content analysis covers strategic and regulatory documents, among them the Fourth National Communication under the UNFCCC and the updated NDC; economic figures come from World Bank, Asian Development Bank and EBRD reporting; physical parameters of the environment were derived by synthesising CMIP6 climate modelling data for Central Asia. Annual damage to the road network from natural hazards stands at USD 45 million, or 0.5% of GDP, and projections push it to USD 80 million by the mid-2030s. Among the surveyed hazardous sites, mudflows account for 36%, avalanches for 31%, rockfalls for 13%. Repair and maintenance costs rise under every scenario examined. Adaptation investment made in time reverses the trend: expected GDP losses fall from 5-6% to 2.0-3.8%. Engineering priorities are best set through cost-benefit analysis. A road maintenance fund and the full deployment of early warning systems are treated here as prerequisites rather than options, while climate criteria should enter road planning regulations through life-cycle assessment.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in “Polytechnic Bulletin” series “Technology and Society”
- Vol. 15 (3)
CLIMATE CHANGE ADAPTATION OF THE TRANSPORT SECTOR OF THE REPUBLIC OF TAJIKISTAN: VULNERABILITY ASSESSMENT, INSTITUTIONAL FRAMEWORK AND IMPLEMENTATION PRACTICE
Mountains cover ninety-three percent of Tajikistan. That single figure shapes the country's logistics: the road network absorbs climate stress with almost no modal alternative behind it. This article assesses the vulnerability of the transport sector and examines the adaptation governance system now taking shape. The design is mixed-method. Content analysis covers strategic and regulatory documents, among them the Fourth National Communication under the UNFCCC and the updated NDC; economic figures come from World Bank, Asian Development Bank and EBRD reporting; physical parameters of the environment were derived by synthesising CMIP6 climate modelling data for Central Asia. Annual damage to the road network from natural hazards stands at USD 45 million, or 0.5% of GDP, and projections push it to USD 80 million by the mid-2030s. Among the surveyed hazardous sites, mudflows account for 36%, avalanches for 31%, rockfalls for 13%. Repair and maintenance costs rise under every scenario examined. Adaptation investment made in time reverses the trend: expected GDP losses fall from 5-6% to 2.0-3.8%. Engineering priorities are best set through cost-benefit analysis. A road maintenance fund and the full deployment of early warning systems are treated here as prerequisites rather than options, while climate criteria should enter road planning regulations through life-cycle assessment.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in Journal of Health
COMPARISON OF ELECTRIC VEHICLE ENERGY CONSUMPTION MODELS AND INTERNAL COMBUSTION ENGINE VEHICLE FUEL CONSUMPTION STANDARDS IN MOUNTAINOUS CONDITIONS (CASE STUDY: KULOB – SHOHON ROUTE)
This paper presents a comparative analysis between the fuel consumption standards for internal combustion engine vehicles currently effective in the Republic of Tajikistan and a previously proposed physical-mathematical model for electric vehicle energy consumption with regenerative braking. The evaluation was conducted on a challenging mountainous route, Kulyab – Shamsiddin Shohin – Shohon (64 km, mountain pass at 1980 m). For a gasoline vehicle weighing 2100 kg (base rate of 10 L/100 km), the elevation surcharge increases consumption by 9.8% (from 6.40 to 7.03 L). For an electric vehicle of equivalent mass, given a baseline flat-terrain consumption of 7.41 kWh, uphill driving increases energy consumption to 9.09 kWh (+22.7%), whereas downhill driving with regenerative braking reduces it to 5.93 kWh (−20.0%). The directional disparity reaches 3.2 kWh, while the average round-trip consumption (7.51 kWh) exceeds the baseline horizontal value by only 1.4%. It is shown that existing standardized methodologies applying equal elevation surcharges in both directions fail to account for the recovery of gravitational potential energy via regenerative braking. These findings justify the necessity of revising operational performance assessment methodologies for electrified transport. Under current electricity and fuel tariffs in Tajikistan, the difference in specific operating costs along this route reaches 22–26 times in favor of the electric vehicle.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in Journal of Health
COMPARISON OF ELECTRIC VEHICLE ENERGY CONSUMPTION MODELS AND INTERNAL COMBUSTION ENGINE VEHICLE FUEL CONSUMPTION STANDARDS IN MOUNTAINOUS CONDITIONS (CASE STUDY: KULOB – SHOHON ROUTE)
This paper presents a comparative analysis between the fuel consumption standards for internal combustion engine vehicles currently effective in the Republic of Tajikistan and a previously proposed physical-mathematical model for electric vehicle energy consumption with regenerative braking. The evaluation was conducted on a challenging mountainous route, Kulyab – Shamsiddin Shohin – Shohon (64 km, mountain pass at 1980 m). For a gasoline vehicle weighing 2100 kg (base rate of 10 L/100 km), the elevation surcharge increases consumption by 9.8% (from 6.40 to 7.03 L). For an electric vehicle of equivalent mass, given a baseline flat-terrain consumption of 7.41 kWh, uphill driving increases energy consumption to 9.09 kWh (+22.7%), whereas downhill driving with regenerative braking reduces it to 5.93 kWh (−20.0%). The directional disparity reaches 3.2 kWh, while the average round-trip consumption (7.51 kWh) exceeds the baseline horizontal value by only 1.4%. It is shown that existing standardized methodologies applying equal elevation surcharges in both directions fail to account for the recovery of gravitational potential energy via regenerative braking. These findings justify the necessity of revising operational performance assessment methodologies for electrified transport. Under current electricity and fuel tariffs in Tajikistan, the difference in specific operating costs along this route reaches 22–26 times in favor of the electric vehicle.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in Journal of Health
INTEGRATED SAFETY, RELIABILITY AND ENVIRONMENTAL FRAMEWORK FOR ROAD TRANSPORT OPERATION IN MOUNTAIN TERRAIN
Safety, mechanical reliability, and environmental efficiency of road transport in mountainous conditions are traditionally studied as isolated problems with separate regulatory frameworks. With the large-scale electrification of the vehicle fleet, this division loses its scientific validity because a single physical mechanism—the degree of energy storage saturation during regenerative braking—simultaneously determines the thermal load of friction brakes, component reliability, and non-exhaust particulate emissions. This study synthesizes four interrelated directions within a unified concept, where the critical length of regeneration exhaustion serves as an interdisciplinary cross-cutting parameter. Based on official traffic accident statistics in the Republic of Tajikistan for 2016–2025, recording a 50.6% increase in fatalities alongside stable accident rates, as well as field tests on 117 tires, it is strictly proven that for a loaded heavy truck, battery capacity is exhausted after 6.9–13.8 km of a descent. Once regeneration ceases, the entire braking load shifts to friction mechanisms not designed for such continuous stress. This threshold directly determines the ratio of non-exhaust emissions from electric vehicles to internal combustion engine emissions. The proposed invariant longitudinal dynamics model enables the scientific optimization and placement of charging infrastructure based on the minimum charge level profile.
- 30 September 2026
- Published by Tajik Technical University named after academician M.S. Osimi in Journal of Health
INTEGRATED SAFETY, RELIABILITY AND ENVIRONMENTAL FRAMEWORK FOR ROAD TRANSPORT OPERATION IN MOUNTAIN TERRAIN
Safety, mechanical reliability, and environmental efficiency of road transport in mountainous conditions are traditionally studied as isolated problems with separate regulatory frameworks. With the large-scale electrification of the vehicle fleet, this division loses its scientific validity because a single physical mechanism—the degree of energy storage saturation during regenerative braking—simultaneously determines the thermal load of friction brakes, component reliability, and non-exhaust particulate emissions. This study synthesizes four interrelated directions within a unified concept, where the critical length of regeneration exhaustion serves as an interdisciplinary cross-cutting parameter. Based on official traffic accident statistics in the Republic of Tajikistan for 2016–2025, recording a 50.6% increase in fatalities alongside stable accident rates, as well as field tests on 117 tires, it is strictly proven that for a loaded heavy truck, battery capacity is exhausted after 6.9–13.8 km of a descent. Once regeneration ceases, the entire braking load shifts to friction mechanisms not designed for such continuous stress. This threshold directly determines the ratio of non-exhaust emissions from electric vehicles to internal combustion engine emissions. The proposed invariant longitudinal dynamics model enables the scientific optimization and placement of charging infrastructure based on the minimum charge level profile.
- 20 June 2026
- Published by Elsevier in Tribology International
- Vol. 224
Influence of muscle fatigue on pain based on friction and brain activation
- 20 June 2026
- Published by Elsevier in Tribology International
- Vol. 224
Influence of muscle fatigue on pain based on friction and brain activation
- 1 January 2024
- Published by Orenburg State University in Intelligence. Innovations. Investment
- No. 5,p. 51-63
TECHNICAL AND ECONOMIC ANALYSIS OF THE USE OF MOBILE CHARGING STATIONS FOR ELECTRIC VEHICLES IN THE REPUBLIC OF TAJIKISTAN
The global electric vehicle market is increasing. The main motivation for switching to this innovative type of vehicle is, first of all, reducing the impact on the environment, reducing operating costs, the possibility of using new technologies in transport, etc. Of course, the development of electric vehicles, like other industries, has its problems. The paper examines the methodology for determining the optimal options for charging infrastructure for electric vehicles, as the main factor influencing the widespread use of electric cars. The purpose of the study is to determine the optimal option for mobile charging stations (MCS) for the conditions of Tajikistan based on a comparative analysis of key indicators: cost, weight and resource. To conduct a study to determine the optimal option for mobile charging stations, a comparative analysis method was used. For the conditions of Tajikistan, to determine the optimal option for mobile charging stations (MCS), a corresponding comparative analysis was carried out in terms of such indicators as cost, weight, and resource. It was revealed that the MCS based on autonomous generators with an internal combustion engine (ICE) is superior to other options in all respects. However, we should not forget that the greatest harm is caused to the environment by such an MCS, and it requires a constant supply of fuel. The best option is to combine lithium-ion batteries with an autonomous generator and a solar battery or wind power plant. Considering that the multi-station system is often located in one place, at the first stage it was proposed to create a multi-station station with an autonomous generator, lead-acid batteries, or a hybrid version. In the future, it is necessary to gradually switch to the joint use of hybrid installations based on lithium-ion batteries in combination with an internal combustion engine, solar panels, or a wind-electric installation. The practi¬cal significance of the study is to create a stable and cost-effective infrastructure for charging electric vehicles, including based on alternative energy sources, in Tajikistan, which contributes to increased mobility, economic development and environmental sustainability of the region. The development of electric vehicle infrastructure will stimulate the growth of the electric vehicle market, which in turn will contribute to the development of related economic sectors. Similar installa¬tions can be used in other industries, such as tourism, power supply to remote villages, and geological exploration.
- 1 January 2024
- Published by Orenburg State University in Intelligence. Innovations. Investment
- No. 5,p. 51-63
TECHNICAL AND ECONOMIC ANALYSIS OF THE USE OF MOBILE CHARGING STATIONS FOR ELECTRIC VEHICLES IN THE REPUBLIC OF TAJIKISTAN
The global electric vehicle market is increasing. The main motivation for switching to this innovative type of vehicle is, first of all, reducing the impact on the environment, reducing operating costs, the possibility of using new technologies in transport, etc. Of course, the development of electric vehicles, like other industries, has its problems. The paper examines the methodology for determining the optimal options for charging infrastructure for electric vehicles, as the main factor influencing the widespread use of electric cars. The purpose of the study is to determine the optimal option for mobile charging stations (MCS) for the conditions of Tajikistan based on a comparative analysis of key indicators: cost, weight and resource. To conduct a study to determine the optimal option for mobile charging stations, a comparative analysis method was used. For the conditions of Tajikistan, to determine the optimal option for mobile charging stations (MCS), a corresponding comparative analysis was carried out in terms of such indicators as cost, weight, and resource. It was revealed that the MCS based on autonomous generators with an internal combustion engine (ICE) is superior to other options in all respects. However, we should not forget that the greatest harm is caused to the environment by such an MCS, and it requires a constant supply of fuel. The best option is to combine lithium-ion batteries with an autonomous generator and a solar battery or wind power plant. Considering that the multi-station system is often located in one place, at the first stage it was proposed to create a multi-station station with an autonomous generator, lead-acid batteries, or a hybrid version. In the future, it is necessary to gradually switch to the joint use of hybrid installations based on lithium-ion batteries in combination with an internal combustion engine, solar panels, or a wind-electric installation. The practi¬cal significance of the study is to create a stable and cost-effective infrastructure for charging electric vehicles, including based on alternative energy sources, in Tajikistan, which contributes to increased mobility, economic development and environmental sustainability of the region. The development of electric vehicle infrastructure will stimulate the growth of the electric vehicle market, which in turn will contribute to the development of related economic sectors. Similar installa¬tions can be used in other industries, such as tourism, power supply to remote villages, and geological exploration.
- 9 September 2022
- Published by Springer Nature
- p. 32-43
Automated Control of the Gear Profile for the Gerotor Hydraulic Machine
- 9 September 2022
- Published by Springer Nature
- p. 32-43
Automated Control of the Gear Profile for the Gerotor Hydraulic Machine
- 25 May 2022
- Published by Springer Nature
- p. 133-143
Reducing Working Fluid Pulsations in Planetary Hydraulic Machines by Rational Design of the Distribution Systems
- 25 May 2022
- Published by Springer Nature
- p. 133-143
Reducing Working Fluid Pulsations in Planetary Hydraulic Machines by Rational Design of the Distribution Systems
- Open Access
- 1 February 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 990 (1) , 012063
Assessment of the resource of elements of transportation machins operated in mining energy enterprises
In mining energy enterprises located at altitudes over 1000 meters above sea level, transport machines are operated in harsh road-climatic conditions, contributing to accelerated wear of equipment and machinery elements. The purpose of the study is related to the assessment and adjustment of the resource of the elements of transport machines operated in mining energy enterprises. The work is devoted to the assessment of the intensity of wear of the elements of machines involved in the transportation of rocks, taking into account the influence of the most significant factors. To assess the resource of elements of transport machines operated in mining energy enterprises, a complex scientific approach was used, taking into account the influence of various combinations of significant factors. The practical significance of the work is associated with planning the need for elements of transport machines operated in mining energy enterprises. The research results, including the simplified mathematical model presented in the article, can be recommended for assessing and adjusting the resource of the elements of transport machines operated in mining energy enterprises.
- 1 February 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 990 (1) , 012063
Open AccessAssessment of the resource of elements of transportation machins operated in mining energy enterprises
In mining energy enterprises located at altitudes over 1000 meters above sea level, transport machines are operated in harsh road-climatic conditions, contributing to accelerated wear of equipment and machinery elements. The purpose of the study is related to the assessment and adjustment of the resource of the elements of transport machines operated in mining energy enterprises. The work is devoted to the assessment of the intensity of wear of the elements of machines involved in the transportation of rocks, taking into account the influence of the most significant factors. To assess the resource of elements of transport machines operated in mining energy enterprises, a complex scientific approach was used, taking into account the influence of various combinations of significant factors. The practical significance of the work is associated with planning the need for elements of transport machines operated in mining energy enterprises. The research results, including the simplified mathematical model presented in the article, can be recommended for assessing and adjusting the resource of the elements of transport machines operated in mining energy enterprises.