SWSagar Wankhede

Sagar Wankhede

*This is an algorithmically generated author record based on publicly available information.

Sagar Wankhede has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental Investigation of a Hybrid Thermal Management System for LFP Battery Packs Using Ag 2 O Nano Fluid–Cooled Serpentine Copper Tubes Embedded in Graphite‐Enhanced PCM

    by Sagar Wankhede, Ajay D. Pingale, Aniruddha Kulkarni, Kunal Kolte, Lalit Jadhav, Lilesh Yadav, Sucheta Kakade, Shweta Suryawanshi

    Effective thermal management is critical to ensure the safety, reliability, and performance of lithium‐ion battery modules under high thermal loads. While hybrid phase change material (PCM)–liquid cooling systems have been widely explored, the present study introduces a novel material‐level enhancement through the use of an Ag 2 O–ethylene glycol Nano fluid, whose application in battery thermal management remains largely unexplored. A compact 4S5P battery module comprising 21 700‐type lithium iron phosphate (LFP) cells (14 V, 22.5 Ah) is experimentally investigated under 1C, 1.5C, and 2C discharge rates, along with 1C charging conditions. The proposed hybrid BTMS integrates PCM with active liquid cooling using Ag 2 O Nano fluid at varying concentrations (1–5 wt.%), enabling a systematic evaluation of its thermo‐physical impact. The results demonstrate that, in the absence of thermal management, the module temperature rapidly increases to approximately 60°C at 2C, indicating severe thermal stress. In contrast, the proposed system significantly enhances heat dissipation, maintaining the maximum cell temperature within 30°C–32°C, thereby achieving a reduction of 5%. Furthermore, increasing nanoparticle concentration improves convective heat transfer, with optimal performance observed at 5 wt.%, reaching temperature to 29°C resulting in improved temperature uniformity across the module. Results demonstrate the effectiveness of Ag 2 O nanofluid relative to base fluid under the investigated operating conditions. This study not only demonstrates the feasibility of Ag 2 O‐based Nano fluids in BTMS but also provides a scalable and high‐performance thermal management solution for high‐power cylindrical battery modules in electric vehicles and energy storage systems.

  • Open Access

    A comparative MATLAB/Simulink framework for drive-cycle-based traction motor sizing in battery electric four-wheelers

    by Shweta S. Suryavanshi, Sagar Wankhede, Pravin M. Ghanegaonkar, Devakant Baviskar, Surekha Khetree, Choon Kit Chan, Sohankumar G. Prajapati, Vijay Chaudhary, Subhav Singh, Deekshant Varshney

    As more battery electric vehicles (BEVs) are being introduced, the need for accurate traction motor sizing to achieve optimal performance, energy efficiency, driving range and cost has become more important. The conventional analytical sizing methods are based on worst-case conditions and often result in over- or under-sizing a motor, with the resulting negative impact on system efficiency and economic viability. In this study, a MATLAB/Simulink model is developed which compares directly between analytical sizing and drive cycle-based simulation of a battery electric four-wheeler for a Maruti Zen passenger car. The equations of the vehicle dynamics with the four forces: rolling resistance, aerodynamic drag, acceleration, and gradient force approximate the tractive force, wheel torque, and motor power. The vehicle is tested in three standardised drive cycles (New European Driving Cycle (NEDC), Highway Fuel Economy Test (HWFET) and the Artemis Urban Drive Cycle (UDC)), and the results are compared to the analytical method. The analytical approach predicts a 23.23–67.99 kW power band for the road gradient range (0°–18°) analysed, while drive-cycle simulation suggests 15.29 kW (NEDC), 14.52 kW (HWFET) and 22.10 kW (UDC)—a 67.5–78.6% decrease from the analytical upper bound. The results show that drive-cycle-based sizing can provide a more accurate, application-specific assessment of traction-motor sizing and help to minimize the risk of over-sizing and increase efficiency. In addition to re-working known vehicle-dynamics equations, this work is novel in that the power gap between the two routes of analytical and drive-cycle sizing is benchmarked for a vehicle and set of parameters, and a low-cost, practical screening tool for selecting a traction motor appropriate for the operating environment and duty profile is provided to manufacturers and researchers.

  • Experimental investigation of heat transfer characteristics of rhamnolipid-based Al2O3 nanofluids in vertical tube subcooled flow boiling

    by Hemantkumar H. Kadam, Sucheta S. Kakde, Ajit Patil, Narendra R. Deore, Sagar R. Wankhede, Siddhanath V. Nishandar, Ashok T. Pise

  • Effect of the Fly Ash Nano Fluid in the Serpentine Channel on Cooling Efficiency Enhancement of EV Battery Thermal Management System

    by Sagar Wankhede, Kaustubh Shahane, Sarvesh Patil, Aditya Patil, Ankush Khandare, Jogi Patel

    Lithium‐ion batteries are the most environmentally friendly energy storage option for existing electric cars and are essential to their operation. Among their many uses are powering electrical gadgets like laptops and cell phones. However, controlling battery temperature is a major design difficulty, especially because charging and discharging operations generate a lot of heat. Li‐ion cell performance can be hampered by inadequate heat transmission between densely packed cells, which can potentially result in safety risks like explosions. Temperatures over or below might affect the vehicle's battery life and range. Therefore, improving heat transport and cooling mechanisms throughout the electric vehicle's battery pack is the goal of this research. The current work focuses on the use of fly ash nanoparticles dispersed in water as a base fluid as coolant in indirect liquid cooling systems. An ANSYS FLUENT model has been developed for 52 NMC cylindrical cells with a 13s4p arrangement and a serpentine cooling channel between the cells. Simulation results show that the incorporation of fly ash Nano fluids decreases the peak temperatures of the battery and ensures uniform temperature distribution, thus optimizing LIB performance. This paper reveals that with the increase in fly ash in water from 0.01% to 0.5%, the heat removal rate has been enhanced by 1.6%. Also, with the increase in the velocity of fly ash‐based Nano fluid, from 1 m/s to 5 m/s, heat removal has been increased by 84.14%. The results encourage the use of fly ash‐based cooling systems for effective and environmentally friendly EV technology.


  • An air‐cooled cylindrical Li‐ion 5 × 5 battery module with a novel flow‐diverting arrangement and variable vent positions for electric vehicles: A numerical thermal analysis

    by Shweta Suryavanshi, P. M. Ghanegaonkar, Sagar Wankhede

    Thermal management of lithium‐ion batteries has received a lot of interest in the automobile sector. In commercial electric motor vehicles, an efficient battery cooling arrangement, particularly active cooling approaches, has been chosen as an ideal option. When building battery cooling systems, the physical structure and arrangement of the battery pack (BP) are vital. The current study presents a revolutionary design of a BP that incorporates cylindrical cells in a square duct and an air‐cooling (AC) medium circulated in its surroundings with the help of variable vents for inlet and outlet. A forced‐AC system is used to test lithium‐ion battery cells grouped in a 5 × 5 configured battery module. To investigate the impact of heat generation on battery thermal performance, a complete thermal analysis was performed at different discharge rates of 0.5, 1, 2, 3, and 4 C. As compared with both inlet vents at an equidistance configuration with an inlet velocity of 12 m/s and a flow rate of 1.210(−2) kg/s, the results show that the proposed design minimizes heat accumulation by enhancing the heat transfer. As a result, the peak temperature and temperature disparity decreased by 6.76% and 85.32%, respectively. A flow‐dispersing disc of 30 mm in size enhances temperature uniformity in comparison to the other intake vent design, hence improving battery safety and longevity.


  • Experimental investigation on an innovative serpentine channel‐based nanofluid cooling technology for modular lithium‐ion battery thermal management

    by Sagar Wankhede, Abhijeet Kore, Laxman Kamble, Pravin Kale

    Many nations have committed to becoming carbon neutral by 2050 as a means of addressing the global warming challenge. To achieve carbon neutrality, transportation is one of the most essential and important tasks. Energy‐efficient pure electric vehicles (EVs) and hybrid electric vehicles (HEVs) with green energy power are being developed in response to the worldwide energy and environmental crises, as the potential replacements for the current generation of combustion‐engine automobiles. EVs require batteries more than ever before. In this perspective, lithium‐ion batteries (LIBs) stand out as remarkable energy storage technologies and have been widely used due to their numerous impressive benefits. Owing to LIBs sensitivity to temperature, EVs typically use the battery thermal management system (BTMS). The working temperature span of a lithium‐ion battery in an electric car is 15°C–35°C, which is achieved by the use of a BTMS. The production of internal heat during charging and discharging also affects how well lithium‐ion batteries work. A battery heat control system is therefore required. The temperature of the LIB pack might be efficiently controlled by liquid‐cooled systems in discharge and charge scenarios. Based on Al2O3 nanofluid (NF), the current experimental study suggests a novel active cooling technology for regulating the heat produced by the 18650‐format lithium‐ion batteries. A thorough analysis is conducted on the impact of charge/discharge C‐rates, Al2O3 nanoparticle (NP) volume fractions, inflow coolant velocity, and intake liquid temperature on the thermal efficiency of the LIB pack. By incorporating aluminum oxide NPs into the water at varying volume fractions of 0.3%, 0.5%, and 1%, the LIB pack's maximum temperature was significantly reduced by 7.9%, 18.09%, and 19.56%, respectively. With increase in mass flow rate of coolant from 0.0290 to 0.5810 kg/s, the maximum temperature has been substantially reduced by 3.7%–8.6%. Results show that using higher fluid inflow temperature significantly increased both the highest experienced temperature and temperature diversity throughout the discharge operation by about, 6°C and 5°C, respectively. The outcomes of the study indicate that NFs exhibit superior cooling performance compared to conventional coolants such as water and ethylene glycol.


  • A review of Li‐ion battery temperature control and a key future perspective on cutting‐edge cooling methods for electrical vehicle applications

    by Sagar Wankhede, Kiran More, Laxman Kamble

    Covid‐19 has given us a new way to look at our globe with regards to minimise air and noise pollution and thereby upgrading global environmental conditions. This positive pandemic outcome indicates that green energy is the future of energy, and one new origin of green energy is lithium‐ion batteries (LIBs). Electric vehicles are constructed with LIBs, but they have a number of disadvantages, including poor thermal performance, thermal runaway, fire dangers and a higher discharge rate in low‐ and high‐temperature conditions. The underlying fault of LIBs is their temperature reactivity. Extreme temperatures and challenging working circumstances can cause lithium‐ion cells to malfunction and cause the battery pack (BP) to overheat. For optimal performance in vehicles and long‐term LIB durability, LIBs must be thermally managed within their operating temperature span. This paper presents an overview of several cooling strategies used to maintain the internal BP temperature. This paper discusses cooling techniques using air, liquid and phase change material (PCM), heat pipe. Additionally, various BP configurations and heat generation techniques are explored. This research also discusses the usage of nanomaterials to address the BP's heat‐related problems. This study emphasises the use of nanomaterial to boost the heat conductivity of coolant in order to raise the batteries temperature into their ideal working range (PCM as well as liquid cooling). This article also provides some of the research gaps that have been found and the crucial areas on which attention should be directed in order to build the best lithium‐ion battery thermal management system technology.


  • Open Access

    A review of Li-ion battery temperature control and a key future perspective on cutting-edge cooling methods for electrical vehicle applications

    by Sagar Wankhede, Kiran More, Laxman Kamble

    Covid-19 has given us a new way to look at our globe with regards to minimize air and noise pollution and thereby upgrading global environmental conditions. This positive pandemic outcome indicates that green energy is the future of energy, and one new origin of green energy is lithium-ion batteries (LIBs). Electric vehicles are constructed with LIBs, but they have a number of disadvantages, including poor thermal performance, thermal runaway, fire dangers, and a higher discharge rate in low- and high-temperature conditions. The underlying fault of LIBs is their temperature reactivity. Extreme temperatures and challenging working circumstances can cause lithium-ion cells to malfunction and cause the battery pack to overheat. For optimal performance in vehicles and long-term lithium-ion battery durability, LIBs must be thermally managed within their operating temperature span. This paper presents an overview of several cooling strategies used to maintain the internal battery pack temperature. This paper discusses cooling techniques using air, liquid, and Phase Change Material (PCM), Heat pipe(HP). Additionally, various battery pack configurations and heat generation techniques are explored. This research also discusses the usage of nanomaterials to address the battery pack’s heat-related problems. This study emphasises the use of nanomaterial to boost the heat conductivity of coolant in order to raise the batteries temperature into their ideal working range (PCM as well as LC). This article also provides some of the research gaps that have been found and the crucial areas on which attention should be directed in order to build the best lithium-ion BTMS technology.


  • Experimental investigation on hybrid cooled lithium‐ion battery pack with 3S4P cell configuration using OM 48 as phase change material and heat pipe

    by Sagar Wankhede, Kiran More, Laxman Kamble, Prajwal Thorat

    Because of their high energy capacity and power density, lithium‐ion batteries are an essential component of electric and hybrid vehicles; however, they frequently experience excessive temperature rise because of heat creation inside the batteries. The charge state and charge/discharge rate play a major role in this heat generation. Due to its high latent heat, compact design and lightweight nature without requiring any external power, passive techniques like phase change material (PCM) and heat pipe (HP) cooling have gained widespread popularity. Therefore, this work focussed on hybrid BTMS integrating Heat Pipe with PCM for better thermal management of battery pack supported by a heat pipe that is used to analyse the thermal performance of a battery module having three and four lithium‐ion batteries placed in series and parallel. The objective of maintaining temperature gradient of less than 5°C between the adjacent cells and maintaining the overall battery temperature in the range of 25°C–45°C has been successfully achieved. The results of experiments at various discharge rates showed that a heat pipe was crucial to quickly transferring heat and maintaining temperature homogeneity for PCM‐based battery modules. It can be concluded that the data presented above can offer views for creating and improving battery heat management systems.