Yudong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yudong Liu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bowen Li
Department of Fluid Control and Automation, School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication - Peng Wang
Harbin Institute of Technology, School of Mechatronics Engineering, Harbin 150001, China
1 shared publication Qingjun Yang
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication- Qingjun Yang
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication - Qitao Huang
Department of Fluid Control and Automation, School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication Rui Zhu
Nanjing Chenguang Grp Co Ltd, Nanjing, China
1 shared publication
Latest Publications
- 3 February 2025
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 26 (4) , 1159-1176
Improvement of the Magnetic Properties of a Moving-Coil-Type High-Speed On–Off Valve for Vehicle Clutch
- 3 February 2025
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 26 (4) , 1159-1176
Improvement of the Magnetic Properties of a Moving-Coil-Type High-Speed On–Off Valve for Vehicle Clutch
- Open Access
Experimental and Numerical Investigation of Motion-Induced Fluid Force for a High-Speed Valve
A high-speed valve (HSV) is used to control the friction plate accurately and flexibly in the shifting stages of an automatic transmission. In the past, the transient modeling and dynamic improvement of HSVs neglected fluid–solid coupling and motion-induced fluid force (MIFF), which made it difficult to improve the response performance and kinetic energy efficiency of HSVs. In order to fully represent the MIFF and internal flow field features, a novel general approximate model for HSVs with a more accurate fidelity unsteady computational fluid dynamics (CFD) analysis is built in this paper. In addition, the experimental data of HSVs when the sphere is moving in oil-free or oil-immersed media are collected to verify the proposed model. In order to validate the model, the mechanism law of buffer groove towards the MIFF is tracked at length. The motion-induced added mass with buffer groove is reduced by 43.9%. The experimental results show that under the working pressure of 1 MPa (rated pressure), the opening time is shortened to 0.90 ms, which is 11.8% shorter than the original structure. The closing time is shortened from 1.5 ms to 1.34 ms, which represents a decrease of 10.7%. The buffer groove improves the kinetic energy efficiency from 41.91% to 46.70% in the start-up phase and from 41.98% to 56.75% in the close-up phase. This study provides a new perspective for improving the dynamic performance and energy efficiency of the system in terms of the MIFF.
Open AccessExperimental and Numerical Investigation of Motion-Induced Fluid Force for a High-Speed Valve
A high-speed valve (HSV) is used to control the friction plate accurately and flexibly in the shifting stages of an automatic transmission. In the past, the transient modeling and dynamic improvement of HSVs neglected fluid–solid coupling and motion-induced fluid force (MIFF), which made it difficult to improve the response performance and kinetic energy efficiency of HSVs. In order to fully represent the MIFF and internal flow field features, a novel general approximate model for HSVs with a more accurate fidelity unsteady computational fluid dynamics (CFD) analysis is built in this paper. In addition, the experimental data of HSVs when the sphere is moving in oil-free or oil-immersed media are collected to verify the proposed model. In order to validate the model, the mechanism law of buffer groove towards the MIFF is tracked at length. The motion-induced added mass with buffer groove is reduced by 43.9%. The experimental results show that under the working pressure of 1 MPa (rated pressure), the opening time is shortened to 0.90 ms, which is 11.8% shorter than the original structure. The closing time is shortened from 1.5 ms to 1.34 ms, which represents a decrease of 10.7%. The buffer groove improves the kinetic energy efficiency from 41.91% to 46.70% in the start-up phase and from 41.98% to 56.75% in the close-up phase. This study provides a new perspective for improving the dynamic performance and energy efficiency of the system in terms of the MIFF.
- Open Access
Modeling and Simulation of Hydraulic Power Take-Off Based on AQWA
The AQWA software is often used to perform hydrodynamic analysis, and it is highly convenient for performing frequency domain simulations of Pelamis-like wave energy converters. However, hydraulic power take-off (PTO) must be simplified to a linear damping model or a Coulomb torque model when performing a time domain simulation. Although these simulation methods can reduce the computational complexity, they may not accurately reflect the energy capture characteristics of the hydraulic PTO. By analyzing system factors such as the flow and pressure of each branch of the hydraulic PTO, the output torque of the hydraulic cylinder to the buoy, and the electromagnetic torque of the generator, a relatively complete hydraulic PTO model is obtained, and the model is applied to AQWA using the FORTRAN language. Comparing and analyzing the simulation results of the linear damping model, the Coulomb torque model, and the hydraulic PTO, we found that the simulation results obtained by the linear damping model are quite different from those of the hydraulic PTO, while the torque characteristics, kinematic characteristics and energy capture characteristics of the Coulomb torque model are closer to those of the hydraulic PTO model. Therefore, it is more appropriate to simplify hydraulic PTO to a Coulomb torque model based on AQWA.
Open AccessModeling and Simulation of Hydraulic Power Take-Off Based on AQWA
The AQWA software is often used to perform hydrodynamic analysis, and it is highly convenient for performing frequency domain simulations of Pelamis-like wave energy converters. However, hydraulic power take-off (PTO) must be simplified to a linear damping model or a Coulomb torque model when performing a time domain simulation. Although these simulation methods can reduce the computational complexity, they may not accurately reflect the energy capture characteristics of the hydraulic PTO. By analyzing system factors such as the flow and pressure of each branch of the hydraulic PTO, the output torque of the hydraulic cylinder to the buoy, and the electromagnetic torque of the generator, a relatively complete hydraulic PTO model is obtained, and the model is applied to AQWA using the FORTRAN language. Comparing and analyzing the simulation results of the linear damping model, the Coulomb torque model, and the hydraulic PTO, we found that the simulation results obtained by the linear damping model are quite different from those of the hydraulic PTO, while the torque characteristics, kinematic characteristics and energy capture characteristics of the Coulomb torque model are closer to those of the hydraulic PTO model. Therefore, it is more appropriate to simplify hydraulic PTO to a Coulomb torque model based on AQWA.