Koteswararao V. Rajulapati
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Koteswararao V. Rajulapati has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
K. Bhanu Sankara Rao
7 shared publicationsDeekshith G. Kalali
5 shared publicationsNanda Kishore Karnam
4 shared publicationsAnjali Kanchi
3 shared publicationsHarita Seekala
International Advanced Research Centre for Powder Metallurgy and New Materials, Balapur, Hyderabad, India
3 shared publicationsManjini Sambandam
JSW Steel limited, Salem works
3 shared publications
Latest Publications
- 30 October 2026
- Published by Wiley in Advanced Healthcare Materials
TiCoCr‐Based Multi‐Principal Element Alloys for Biomedical Applications
Next‐generation biomedical implants require materials with excellent wear resistance, corrosion resistance, and biocompatibility. This study developed two novel multi‐principal element alloys (MPEAs) based on the TiCoCr composition (equiatomic and non‐equiatomic) with ultra‐high hardness, excellent wear resistance, corrosion stability, and biocompatibility. The as‐cast microstructures revealed a multiphase combination of Ti‐rich hexagonal closed packing (HCP), C 14 Laves, and face‐centered cubic (FCC) phases. Upon heat treatment, equiatomic (Ti 33 Co 33 Cr 33 ) MPEA developed two major body‐centered (BCC) phases and a minor HCP phase, whereas heat treatment of non‐equiatomic (Ti 50 Co 25 Cr 25 ) MPEA revealed one BCC and C 14 Laves phase. The hardness of both MPEAs was slightly reduced after heat treatment. Wear and corrosion tests conducted in Hanks' balanced salt solution (HBSS) at 37°C on heat‐treated MPEAs demonstrated improved tribological and corrosion behavior, with reduced wear and a lower coefficient of friction (COF). Electrochemical analysis indicated superior corrosion resistance, particularly for Ti 33 Co 33 Cr 33 MPEA. With respect to biocompatibility, both MPEAs demonstrated excellent cell adhesion and proliferation properties. Cell viability improved significantly, increasing from the control (100%) to ∼105% and 115% after 3 and 5 days, respectively. The combined results highlight the strong potential of these MPEAs for biomedical applications, offering a unique balance of high “density‐normalized” hardness, excellent corrosion resistance, and biological compatibility for future implant solutions.
- 30 October 2026
- Published by Wiley in Advanced Healthcare Materials
TiCoCr‐Based Multi‐Principal Element Alloys for Biomedical Applications
Next‐generation biomedical implants require materials with excellent wear resistance, corrosion resistance, and biocompatibility. This study developed two novel multi‐principal element alloys (MPEAs) based on the TiCoCr composition (equiatomic and non‐equiatomic) with ultra‐high hardness, excellent wear resistance, corrosion stability, and biocompatibility. The as‐cast microstructures revealed a multiphase combination of Ti‐rich hexagonal closed packing (HCP), C 14 Laves, and face‐centered cubic (FCC) phases. Upon heat treatment, equiatomic (Ti 33 Co 33 Cr 33 ) MPEA developed two major body‐centered (BCC) phases and a minor HCP phase, whereas heat treatment of non‐equiatomic (Ti 50 Co 25 Cr 25 ) MPEA revealed one BCC and C 14 Laves phase. The hardness of both MPEAs was slightly reduced after heat treatment. Wear and corrosion tests conducted in Hanks' balanced salt solution (HBSS) at 37°C on heat‐treated MPEAs demonstrated improved tribological and corrosion behavior, with reduced wear and a lower coefficient of friction (COF). Electrochemical analysis indicated superior corrosion resistance, particularly for Ti 33 Co 33 Cr 33 MPEA. With respect to biocompatibility, both MPEAs demonstrated excellent cell adhesion and proliferation properties. Cell viability improved significantly, increasing from the control (100%) to ∼105% and 115% after 3 and 5 days, respectively. The combined results highlight the strong potential of these MPEAs for biomedical applications, offering a unique balance of high “density‐normalized” hardness, excellent corrosion resistance, and biological compatibility for future implant solutions.
- 26 February 2026
- Published by American Chemical Society (ACS) in ACS Biomaterials Science & Engineering
- Vol. 12 (6) , 2878-2889
Corrosion and Wear Properties of Low-Modulus TiZrNb-Based Complex Concentrated Alloys under Simulated Physiological Conditions
Titanium (Ti) and its alloys have evolved through multiple generations to possess enhanced biomedical performance. However, challenges such as stress shielding, low yield strength, and inadequate corrosion resistance persist in conventional Ti-based alloys. In this study, we explore the complex concentrated alloy (CCA) approach to develop two novel Ti-Zr-Nb alloys: Ti50Zr35Nb15 and Zr50Ti35Nb15. These compositions were designed using CALPHAD-based phase stability predictions based on nontoxic lightweight approach and fabricated via vacuum arc melting, yielding a single-phase body-centered cubic (BCC) structure with large equiaxed grains. The CCAs exhibit higher hardness (∼1.95 GPa) and lower elastic modulus (∼99-102 GPa) than traditional Ti alloys, making them more compatible with human bone. Electrochemical analyses, performed under simulated physiological conditions (Hanks' solution and at 37 °C) confirm superior corrosion resistance for both the CCAs. Tribological studies (performed in Hanks' solution and at 37 °C) reveal improved wear behavior, with the formation of smeared patches reducing material loss and enhancing surface stability. The combination of high hardness, low modulus, excellent corrosion resistance, and favorable wear characteristics under simulated physiological conditions, makes these CCAs promising candidates for next-generation orthopedic and dental implant applications.
- 26 February 2026
- Published by American Chemical Society (ACS) in ACS Biomaterials Science & Engineering
- Vol. 12 (6) , 2878-2889
Corrosion and Wear Properties of Low-Modulus TiZrNb-Based Complex Concentrated Alloys under Simulated Physiological Conditions
Titanium (Ti) and its alloys have evolved through multiple generations to possess enhanced biomedical performance. However, challenges such as stress shielding, low yield strength, and inadequate corrosion resistance persist in conventional Ti-based alloys. In this study, we explore the complex concentrated alloy (CCA) approach to develop two novel Ti-Zr-Nb alloys: Ti50Zr35Nb15 and Zr50Ti35Nb15. These compositions were designed using CALPHAD-based phase stability predictions based on nontoxic lightweight approach and fabricated via vacuum arc melting, yielding a single-phase body-centered cubic (BCC) structure with large equiaxed grains. The CCAs exhibit higher hardness (∼1.95 GPa) and lower elastic modulus (∼99-102 GPa) than traditional Ti alloys, making them more compatible with human bone. Electrochemical analyses, performed under simulated physiological conditions (Hanks' solution and at 37 °C) confirm superior corrosion resistance for both the CCAs. Tribological studies (performed in Hanks' solution and at 37 °C) reveal improved wear behavior, with the formation of smeared patches reducing material loss and enhancing surface stability. The combination of high hardness, low modulus, excellent corrosion resistance, and favorable wear characteristics under simulated physiological conditions, makes these CCAs promising candidates for next-generation orthopedic and dental implant applications.
- 8 January 2026
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (3) , 1014-1033
Effects of Temperature and Loading Conditions (Monotonic/Cyclic) on the Microstructural Evolution and Phase Stability of Martempered SAE 9254 Spring Steel
- 8 January 2026
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (3) , 1014-1033
Effects of Temperature and Loading Conditions (Monotonic/Cyclic) on the Microstructural Evolution and Phase Stability of Martempered SAE 9254 Spring Steel
- 16 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
On the microstructural evolution and indentation response of equiatomic NbWTi medium-entropy alloy
- 16 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
On the microstructural evolution and indentation response of equiatomic NbWTi medium-entropy alloy
- 3 February 2025
- Published by Springer Nature in Journal of Materials Research
- Vol. 40 (5) , 782-792
Assessment of stability of retained austenite during instrumented indentation of martempered SAE 9254 spring steel
- 3 February 2025
- Published by Springer Nature in Journal of Materials Research
- Vol. 40 (5) , 782-792
Assessment of stability of retained austenite during instrumented indentation of martempered SAE 9254 spring steel
- Open Access
- 27 December 2024
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 9
Multi-phase nanocrystalline MoNb (Fe) and MoNbTi (Fe) based multi-principal element alloys with superior “density-normalized” hardness
- 27 December 2024
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 9
Open AccessMulti-phase nanocrystalline MoNb (Fe) and MoNbTi (Fe) based multi-principal element alloys with superior “density-normalized” hardness
- 16 December 2024
- Published by Elsevier in Intermetallics
- Vol. 177
High-temperature oxidation behavior of Nbx(MoTaW)(1-x) (x = 0.25, 0.4, 0.55, and 0.7) refractory multicomponent alloys
- 16 December 2024
- Published by Elsevier in Intermetallics
- Vol. 177
High-temperature oxidation behavior of Nbx(MoTaW)(1-x) (x = 0.25, 0.4, 0.55, and 0.7) refractory multicomponent alloys