Ivo Draganov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ivo Draganov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Nikolay Ferdinandov
University of Ruse
3 shared publicationsDanail Gospodinov
University of Ruse
2 shared publications- Danail Gospodinov
Department of Materials Science and Technology, University of Ruse “Angel Kanchev”, 8 Studentska St., 7017 Ruse, Bulgaria
2 shared publications - Nikolay Ferdinandov
Department of Materials Science and Technology, University of Ruse “Angel Kanchev”, 8 Studentska St., 7017 Ruse, Bulgaria
2 shared publications Rossen Radev
University of Ruse
2 shared publications- Rossen Radev
Department of Materials Science and Technology, University of Ruse “Angel Kanchev”, 8 Studentska St., 7017 Ruse, Bulgaria
2 shared publications
Latest Publications
- Open Access
- 5 October 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (5) , 225
Multi-Criteria Calibration of a Thermo-Mechanical Model of Steel Plate Welding in Vacuum
This paper proposes a procedurefor multi-criteria calibration of a thermo-mechanical model for numerical simulation of welding in the space vacuum. A finite-element model of a steel plate is created. Experimental and computational data are obtained. An inverse problem is formulated for the vector identification of five calibration parameters from the heat-flow model. They are evaluated for adequacy with controlled accuracy according to four criteria. An optimization problem is solved using a two-step interactive procedure. The parameter space studying method (PSI) has been applied to the study of multidimensional regions by means of quasi-uniform sounding. A Pareto-optimal set is defined. It is used to determine reduced ranked Pareto subsets by μ-selection. Salukvadze optimum is also determined.
- 5 October 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (5) , 225
Open AccessMulti-Criteria Calibration of a Thermo-Mechanical Model of Steel Plate Welding in Vacuum
This paper proposes a procedurefor multi-criteria calibration of a thermo-mechanical model for numerical simulation of welding in the space vacuum. A finite-element model of a steel plate is created. Experimental and computational data are obtained. An inverse problem is formulated for the vector identification of five calibration parameters from the heat-flow model. They are evaluated for adequacy with controlled accuracy according to four criteria. An optimization problem is solved using a two-step interactive procedure. The parameter space studying method (PSI) has been applied to the study of multidimensional regions by means of quasi-uniform sounding. A Pareto-optimal set is defined. It is used to determine reduced ranked Pareto subsets by μ-selection. Salukvadze optimum is also determined.
- Open Access
- 30 September 2024
- Published by MDPI AG in Preprints.org
Multi-Criteria Calibration of a Thermo-Mechanical Model of Steel Plate Welding in Vacuum
This paper proposes a methodology for multi-criteria calibration of a thermo-mechanical model for numerical simulation of welding in vacuum. A finite element model of a steel plate is created. Experimental and computational data are obtained. An inverse problem is formulated for the vector identification of five calibration parameters from the heat flow model. They are evaluated for adequacy with controlled accuracy according to four criteria. An optimization problem is solved using a two-step interactive procedure. The parameter space studying method (PSI) has been applied to the study of multidimensional regions by means of quasi-uniform sounding. A Pareto-optimal set is defined. It is used to determine reduced ranked Pareto subsets by -selection. Salukvadze optimum is also determined.
- 30 September 2024
- Published by MDPI AG in Preprints.org
Open AccessMulti-Criteria Calibration of a Thermo-Mechanical Model of Steel Plate Welding in Vacuum
This paper proposes a methodology for multi-criteria calibration of a thermo-mechanical model for numerical simulation of welding in vacuum. A finite element model of a steel plate is created. Experimental and computational data are obtained. An inverse problem is formulated for the vector identification of five calibration parameters from the heat flow model. They are evaluated for adequacy with controlled accuracy according to four criteria. An optimization problem is solved using a two-step interactive procedure. The parameter space studying method (PSI) has been applied to the study of multidimensional regions by means of quasi-uniform sounding. A Pareto-optimal set is defined. It is used to determine reduced ranked Pareto subsets by -selection. Salukvadze optimum is also determined.
- Open Access
- 22 June 2024
- Published by Riga Technical University in ENVIRONMENT. TECHNOLOGIES. RESOURCES. Proceedings of the International Scientific and Practical Conference
- Vol. 3, 375-380
NUMERICAL MODELING OF LASER TRANSMISSION WELDING: STATE OF THE ART
This work presents the current state of the numerical modeling of laser transmission welding. A review of publications with a similar theme was made and some aspects that remained outside the focus of the authors were highlighted. Laser transmission welding is a technological process, the physical description of which requires the consideration of several physical laws, which are discussed here. Works were reviewed in which the numerical model is based on: the law of conservation of energy, Fourier's law of heat transfer, Lambert-Beer's law of light propagation, Newton's law of convective heat transfer, Stefan-Boltzmann's law of radiant heat transfer, the Navier-Stokes equation for a fluid, the laws of mechanics for a deformable solid along with the criteria for plasticity. Since their joint solution in analytical form is not possible, the authors' approach is to single out one or several of the laws and use numerical methods to solve the differential equations that describe them. In this work, the use of several numerical methods is considered, and the finite element method is most often used for the discretization of space. The programs used by the authors for the numerical modeling of laser transmission welding are mentioned. The results obtained for the temperature field, heat affected zone and weld pool dimensions, voids, material degradation, residual stresses and weld pool flow rate are discussed. Particular attention is paid to the issues of calibration, verification and validation of numerical models. Some conclusions and directions are highlighted, emphasizing not so much the physical interpretation of the obtained results, but the essence of numerical modeling.
- 22 June 2024
- Published by Riga Technical University in ENVIRONMENT. TECHNOLOGIES. RESOURCES. Proceedings of the International Scientific and Practical Conference
- Vol. 3, 375-380
Open AccessNUMERICAL MODELING OF LASER TRANSMISSION WELDING: STATE OF THE ART
This work presents the current state of the numerical modeling of laser transmission welding. A review of publications with a similar theme was made and some aspects that remained outside the focus of the authors were highlighted. Laser transmission welding is a technological process, the physical description of which requires the consideration of several physical laws, which are discussed here. Works were reviewed in which the numerical model is based on: the law of conservation of energy, Fourier's law of heat transfer, Lambert-Beer's law of light propagation, Newton's law of convective heat transfer, Stefan-Boltzmann's law of radiant heat transfer, the Navier-Stokes equation for a fluid, the laws of mechanics for a deformable solid along with the criteria for plasticity. Since their joint solution in analytical form is not possible, the authors' approach is to single out one or several of the laws and use numerical methods to solve the differential equations that describe them. In this work, the use of several numerical methods is considered, and the finite element method is most often used for the discretization of space. The programs used by the authors for the numerical modeling of laser transmission welding are mentioned. The results obtained for the temperature field, heat affected zone and weld pool dimensions, voids, material degradation, residual stresses and weld pool flow rate are discussed. Particular attention is paid to the issues of calibration, verification and validation of numerical models. Some conclusions and directions are highlighted, emphasizing not so much the physical interpretation of the obtained results, but the essence of numerical modeling.
- Open Access
- 16 January 2024
- Published by Riga Technical University in ENVIRONMENT. TECHNOLOGIES. RESOURCES. Proceedings of the International Scientific and Practical Conference
- Vol. 3, 328-333
APPLICATION OF A FINITE ELEMENT MODEL TO OBTAIN THE INFLUENCE OF THE TREATMENT’S POWER, REFLECION AND FOCAL DIAMETER IN LASER TEXTURING OF ALUMINUM
In this work, a numerical model of laser texturing is considered. A finite element model of a representative sample of pure aluminum was created. The impact of a laser pulse was simulated, assuming a Gaussian volume distribution of the heat flux. Material properties are assumed to be constant and latent heat is accounted for. Results are obtained for the thermal field and the width of the vaporized zone, assuming that the crater is characterized by its maximum width. The numerical model was used to study the influence of pulse power density, reflection, focal diameter and pulse duration. The ablation threshold at different laser pulse durations was determinate.
- 16 January 2024
- Published by Riga Technical University in ENVIRONMENT. TECHNOLOGIES. RESOURCES. Proceedings of the International Scientific and Practical Conference
- Vol. 3, 328-333
Open AccessAPPLICATION OF A FINITE ELEMENT MODEL TO OBTAIN THE INFLUENCE OF THE TREATMENT’S POWER, REFLECION AND FOCAL DIAMETER IN LASER TEXTURING OF ALUMINUM
In this work, a numerical model of laser texturing is considered. A finite element model of a representative sample of pure aluminum was created. The impact of a laser pulse was simulated, assuming a Gaussian volume distribution of the heat flux. Material properties are assumed to be constant and latent heat is accounted for. Results are obtained for the thermal field and the width of the vaporized zone, assuming that the crater is characterized by its maximum width. The numerical model was used to study the influence of pulse power density, reflection, focal diameter and pulse duration. The ablation threshold at different laser pulse durations was determinate.
- 28 August 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1096, 193-203
Finite Element Modeling and Verification of the Plunge Stage in Friction Stir Welding
In the present work, a finite element model of the first stage, plunge, of friction stir welding is considered. The welded parts are flat aluminum 1050 plates. The arbitrary Lagrangian-Eulerian formulation implemented in ABAQUS/Explicit is used. The material model of the welded parts is the Johnson-Cook law, and Coulomb’s law describes the friction between the tool and the weldment. Temperature field during the process is obtained, and the influence of the parameters concerning the algorithmic implementation of the finite element method is established. The simulation results are compared with experimental results obtained for this purpose.
- 28 August 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1096, 193-203
Finite Element Modeling and Verification of the Plunge Stage in Friction Stir Welding
In the present work, a finite element model of the first stage, plunge, of friction stir welding is considered. The welded parts are flat aluminum 1050 plates. The arbitrary Lagrangian-Eulerian formulation implemented in ABAQUS/Explicit is used. The material model of the welded parts is the Johnson-Cook law, and Coulomb’s law describes the friction between the tool and the weldment. Temperature field during the process is obtained, and the influence of the parameters concerning the algorithmic implementation of the finite element method is established. The simulation results are compared with experimental results obtained for this purpose.
- 27 May 2022
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 416, 67-75
Comparison of Two Numerical Models for Friction Stir Welding
In this paper, two numerical models of friction stir welding of two aluminum plates are considered. The coupled mechanical-temperature problem is solved with explicit integration over the time. The two models are based on the finite elements method (FEM) and have different complexity and number of participating parameters. The aim of the development is to highlight the weaknesses and strengths of the models of different complexity. The first model is simpler and it is based on the free penetration of the tool into the parts. The second model is based on the arbitrary Lagrange-Euler method and take in to the account the instrument penetration that allows to take into account the movement of the material in the process area. Convective and radiative heat transfers are accounted in the two models. The results for the temperature, stress and strain in the welded joint are studied and compared. The calculation time is given for each model. A parametric analysis was performed for the influence of the rotational speed of the pin, welding velocity and the pressing force. The influence of the temperature dependent physical properties of the welded plates is determined and compared for the both finite element models.
- 27 May 2022
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 416, 67-75
Comparison of Two Numerical Models for Friction Stir Welding
In this paper, two numerical models of friction stir welding of two aluminum plates are considered. The coupled mechanical-temperature problem is solved with explicit integration over the time. The two models are based on the finite elements method (FEM) and have different complexity and number of participating parameters. The aim of the development is to highlight the weaknesses and strengths of the models of different complexity. The first model is simpler and it is based on the free penetration of the tool into the parts. The second model is based on the arbitrary Lagrange-Euler method and take in to the account the instrument penetration that allows to take into account the movement of the material in the process area. Convective and radiative heat transfers are accounted in the two models. The results for the temperature, stress and strain in the welded joint are studied and compared. The calculation time is given for each model. A parametric analysis was performed for the influence of the rotational speed of the pin, welding velocity and the pressing force. The influence of the temperature dependent physical properties of the welded plates is determined and compared for the both finite element models.
- 23 June 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 890, 190-200
Numerical Modeling for the Submerging Arc Welding of S700MC Steel
This paper presents a finite element model of submerged arc welding. The modeling of the filler material has been performed by applying the technique for deactivation and subsequent activation of the finite elements involved in the welding seams. The nonlinear material properties are taken into account. The description of the peaks in the specific heat capacity in the phase changes has been done by introducing latent heat. The welding arc is modeled as a heat source with a constant heat flux density. Experiments have been conducted to validate and verify the numerical model. The influence of the ratio between surface and volume of the set heat sources has been studied. Tack welds have been taken into account. Data on the relationship between the accuracy of the obtained results and the number of passages has been presented.
- 23 June 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 890, 190-200
Numerical Modeling for the Submerging Arc Welding of S700MC Steel
This paper presents a finite element model of submerged arc welding. The modeling of the filler material has been performed by applying the technique for deactivation and subsequent activation of the finite elements involved in the welding seams. The nonlinear material properties are taken into account. The description of the peaks in the specific heat capacity in the phase changes has been done by introducing latent heat. The welding arc is modeled as a heat source with a constant heat flux density. Experiments have been conducted to validate and verify the numerical model. The influence of the ratio between surface and volume of the set heat sources has been studied. Tack welds have been taken into account. Data on the relationship between the accuracy of the obtained results and the number of passages has been presented.
- Open Access
- 3 October 2018
- Published by Silesian University of Technology in Transport Problems
- Vol. 13 (3) , 97-108
SOME GUIDANCE IN THE DESIGNING OF A ROLLER FOR THE AUTOMOTIVE TESTERS
This work presents some aspects related to the designing of a roller for stands that are intended to determine the parameters of the transmission of a vehicle, such as braking force, wheel revolutions, etc. The computational scheme of simply supported beam is used to create an analytical mechanical-mathematical model through which a multicriteria optimization problem has been solved. A finite element macro and submodel of the roller has been created, and by using the R1MS technique, the fatigue strength in the welding seams in the roller has also been determined. A parametric analysis is accomplished to determine the influence of the thickness of the base steel and the covering ebonite layer on the perimeter change of the outer surface, taking into account the physical non-linearity of the outer layer.
- 3 October 2018
- Published by Silesian University of Technology in Transport Problems
- Vol. 13 (3) , 97-108
Open AccessSOME GUIDANCE IN THE DESIGNING OF A ROLLER FOR THE AUTOMOTIVE TESTERS
This work presents some aspects related to the designing of a roller for stands that are intended to determine the parameters of the transmission of a vehicle, such as braking force, wheel revolutions, etc. The computational scheme of simply supported beam is used to create an analytical mechanical-mathematical model through which a multicriteria optimization problem has been solved. A finite element macro and submodel of the roller has been created, and by using the R1MS technique, the fatigue strength in the welding seams in the roller has also been determined. A parametric analysis is accomplished to determine the influence of the thickness of the base steel and the covering ebonite layer on the perimeter change of the outer surface, taking into account the physical non-linearity of the outer layer.