Jin‐Lin Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jin‐Lin Yang has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Hong Jin Fan
School of Physical and Mathematical Sciences, Nanyang Technological University, Singapore, Singapore
19 shared publications - Peihua Yang
The Institute of Technological Sciences School of Integrated Circuits Wuhan University Wuhan China
9 shared publications - Jia Li
School of Electronic and Electrical Engineering, Nanyang Technological University (NTU), 50 Nanyang Avenue, Singapore 639798, Singapore
7 shared publications - Kang Liu
MOE Key Laboratory of Hydraulic Machinery Transients, School of Power and Mechanical Engineering, Wuhan University, Wuhan, China
7 shared publications - Tao Xiao
School of Physical and Mathematical Sciences
6 shared publications Hao Wu
5 shared publications
Latest Publications
- 6 October 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (41) , 45288
Correction to “Dynamic Adaptive Interfaces Enable Zn-Iodine Hydrogel Batteries with High Areal Capacity and Low Self-Discharge”
- 6 October 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (41) , 45288
Correction to “Dynamic Adaptive Interfaces Enable Zn-Iodine Hydrogel Batteries with High Areal Capacity and Low Self-Discharge”
- 19 September 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (38) , 41582-41592
Activating Aqueous Multivalent Metal–Sulfur Electrochemistry via Kinetic Promoter
Sulfur-based aqueous batteries for sustainable energy storage have the advantages of material abundance, low cost, and high theoretical capacity. While aqueous multivalent metal–sulfur electrochemistry is effective in suppressing sulfide dissolution due to its low solubility product constant, it is intrinsically limited by sluggish conversion kinetics. Here, we decouple sulfur-conversion kinetics from sulfur-species stabilization by introducing a kinetic promoter. Operando spectroscopy, electrochemical quartz crystal microbalance analysis, and density functional theory simulations reveal that the Li+ promoter preferentially targets long-chain sulfur species and lowers the redox barrier, while Mn2+ anchors sulfur species and immobilizes short-chain intermediates, steering the reaction from a dissolution route to a rapid, solid-state-dominated pathway. This cooperative mechanism induces the formation of a highly reversible ternary solid phase with an apparent average composition close to Li4Mn6S8, suppressing the accumulation of soluble polysulfide intermediates and enabling deep discharge at ultrahigh rates. Consequently, the SABs with kinetic promoter exhibit highly reversible sulfur redox chemistry with a capacity of 1012 mAh g–1 at 15 A g–1. We also demonstrate the strategy in Zn2+-S and Ni2+-S systems, illustrating its effectiveness in various multivalent aqueous sulfur batteries.
- 19 September 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (38) , 41582-41592
Activating Aqueous Multivalent Metal–Sulfur Electrochemistry via Kinetic Promoter
Sulfur-based aqueous batteries for sustainable energy storage have the advantages of material abundance, low cost, and high theoretical capacity. While aqueous multivalent metal–sulfur electrochemistry is effective in suppressing sulfide dissolution due to its low solubility product constant, it is intrinsically limited by sluggish conversion kinetics. Here, we decouple sulfur-conversion kinetics from sulfur-species stabilization by introducing a kinetic promoter. Operando spectroscopy, electrochemical quartz crystal microbalance analysis, and density functional theory simulations reveal that the Li+ promoter preferentially targets long-chain sulfur species and lowers the redox barrier, while Mn2+ anchors sulfur species and immobilizes short-chain intermediates, steering the reaction from a dissolution route to a rapid, solid-state-dominated pathway. This cooperative mechanism induces the formation of a highly reversible ternary solid phase with an apparent average composition close to Li4Mn6S8, suppressing the accumulation of soluble polysulfide intermediates and enabling deep discharge at ultrahigh rates. Consequently, the SABs with kinetic promoter exhibit highly reversible sulfur redox chemistry with a capacity of 1012 mAh g–1 at 15 A g–1. We also demonstrate the strategy in Zn2+-S and Ni2+-S systems, illustrating its effectiveness in various multivalent aqueous sulfur batteries.
- 24 June 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (26) , 27858-27868
Dynamic Adaptive Interfaces Enable Zn-Iodine Hydrogel Batteries with High Areal Capacity and Low Self-Discharge
Serious self-discharge due to side reactions and the shuttle effect has been formidable limits for liquid zinc-iodine batteries. Hydrogel electrolytes can reduce self-discharge in certain degree and induce new properties of biocompatibility and mechanical flexibility. However, without a proper interface, chemical welding, most hydrogel ZIBs suffer from poor interfacial robustness, particularly under deformation, compromising the battery cycle life. To mitigate this issue, we deploy an in situ integration strategy to construct chemo-mechanical dynamically adaptive interfaces to enable high-iodine-loading hydrogel batteries. On the anode side, the interfacial polycatecholamine accommodates surface evolution via robust adhesion, induces a stable hybrid interphase, and functions as an ion sieve. Simultaneously, the hydrogel permeates the dry-processed cathode, forming a low-tortuosity ion transport pathway that adapts to volume fluctuations and chemically immobilizes polyiodides. This dual-role strategy enables low self-discharge (∼20% loss after 200 h) and unlocks the potential for high areal capacity (∼12.5 mAh cm-2) in thick cathodes. At an areal capacity of ∼5 mAh cm-2 (>40 mg cm-2 iodine loading), the hydrogel battery can sustain over 2200 cycles with a negligible capacity decay of 0.0063% per cycle.
- 24 June 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (26) , 27858-27868
Dynamic Adaptive Interfaces Enable Zn-Iodine Hydrogel Batteries with High Areal Capacity and Low Self-Discharge
Serious self-discharge due to side reactions and the shuttle effect has been formidable limits for liquid zinc-iodine batteries. Hydrogel electrolytes can reduce self-discharge in certain degree and induce new properties of biocompatibility and mechanical flexibility. However, without a proper interface, chemical welding, most hydrogel ZIBs suffer from poor interfacial robustness, particularly under deformation, compromising the battery cycle life. To mitigate this issue, we deploy an in situ integration strategy to construct chemo-mechanical dynamically adaptive interfaces to enable high-iodine-loading hydrogel batteries. On the anode side, the interfacial polycatecholamine accommodates surface evolution via robust adhesion, induces a stable hybrid interphase, and functions as an ion sieve. Simultaneously, the hydrogel permeates the dry-processed cathode, forming a low-tortuosity ion transport pathway that adapts to volume fluctuations and chemically immobilizes polyiodides. This dual-role strategy enables low self-discharge (∼20% loss after 200 h) and unlocks the potential for high areal capacity (∼12.5 mAh cm-2) in thick cathodes. At an areal capacity of ∼5 mAh cm-2 (>40 mg cm-2 iodine loading), the hydrogel battery can sustain over 2200 cycles with a negligible capacity decay of 0.0063% per cycle.
- 26 November 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (27)
Conquering Zn Dendrites via Crystal‐Facet Manipulation and Water‐Repellent Interphase Construction
Aqueous zinc‐ion batteries (AZIBs) are impeded by hydrogen evolution and uncontrolled dendrite growth on Zn metal anodes. A simple, solution‐based strategy is proposed to simultaneously direct crystallographic deposition and reduce interfacial water activity. Cinnamaldehyde (CA) is employed as a molecular surface modifier to form an artificial solid‐electrolyte interphase (ASEI) via a brief immersion. The aromatic moiety of CA imparts strong hydrophobicity, further suppressing water‐triggered side reactions. At the meantime, CA exhibits facet‐selective adsorption, preferentially passivating Zn (002) and (100) planes and thereby guiding Zn 2+ deposition along the (101) orientation. The (101) facet provides intermediate surface energy and plating/stripping barriers, promoting uniform epitaxial growth, improved corrosion resistance, and reduced polarization. Consequently, CA‐modified Zn symmetric cells sustain >2000 h at 1 mA cm −2 with 1 mAh cm −2 . In Zn‖NVO full cells, a specific capacity exceeding 160 mAh g −1 can be maintained after 1000 cycles at 1 A g −1 . This facet‐directed ASEI engineering offers a practical and scalable route to long‐life, dendrite‐resistant Zn anodes for AZIBs.
- 26 November 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (27)
Conquering Zn Dendrites via Crystal‐Facet Manipulation and Water‐Repellent Interphase Construction
Aqueous zinc‐ion batteries (AZIBs) are impeded by hydrogen evolution and uncontrolled dendrite growth on Zn metal anodes. A simple, solution‐based strategy is proposed to simultaneously direct crystallographic deposition and reduce interfacial water activity. Cinnamaldehyde (CA) is employed as a molecular surface modifier to form an artificial solid‐electrolyte interphase (ASEI) via a brief immersion. The aromatic moiety of CA imparts strong hydrophobicity, further suppressing water‐triggered side reactions. At the meantime, CA exhibits facet‐selective adsorption, preferentially passivating Zn (002) and (100) planes and thereby guiding Zn 2+ deposition along the (101) orientation. The (101) facet provides intermediate surface energy and plating/stripping barriers, promoting uniform epitaxial growth, improved corrosion resistance, and reduced polarization. Consequently, CA‐modified Zn symmetric cells sustain >2000 h at 1 mA cm −2 with 1 mAh cm −2 . In Zn‖NVO full cells, a specific capacity exceeding 160 mAh g −1 can be maintained after 1000 cycles at 1 A g −1 . This facet‐directed ASEI engineering offers a practical and scalable route to long‐life, dendrite‐resistant Zn anodes for AZIBs.
- Open Access
- 7 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
High-dimensional strain unlocks fast polysulfide redox kinetics for lithium-sulfur batteries
Strain engineering is an effective approach to enhancing the activity of catalysts by tuning the electrical and geometric configurations. However, the impact of strain dimension on the sulfur redox kinetics and polysulfide adsorption configuration has yet been deciphered. Herein, we employ a biaxial-strained dichalcogenide catalyst with highly curved basal planes to activate the reserve metal atoms and realize efficient lithium-sulfur batteries. The high-dimensional strain enhances the exposure of Mo sites, thereby shifting the polysulfide adsorption mechanism from weak Li-S/Se bonding to strong S*-Mo bonding. Moreover, biaxial strain upshifts both d and p band centers, fostering the interfacial charge transfer and catalytic activity. Based on this mechanism, we obtain apparent correlations between biaxial strain and apparent activation energy for sulfur species conversion. This d-p hybridization dominated catalytic mechanism leads to obvious enhancement in capacity retention and rate performance. We showcase a 6 Ah-level multilayer pouch cell with a specific energy of 396 Wh kg–1 (based on masses of all components).
- 7 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
Open AccessHigh-dimensional strain unlocks fast polysulfide redox kinetics for lithium-sulfur batteries
Strain engineering is an effective approach to enhancing the activity of catalysts by tuning the electrical and geometric configurations. However, the impact of strain dimension on the sulfur redox kinetics and polysulfide adsorption configuration has yet been deciphered. Herein, we employ a biaxial-strained dichalcogenide catalyst with highly curved basal planes to activate the reserve metal atoms and realize efficient lithium-sulfur batteries. The high-dimensional strain enhances the exposure of Mo sites, thereby shifting the polysulfide adsorption mechanism from weak Li-S/Se bonding to strong S*-Mo bonding. Moreover, biaxial strain upshifts both d and p band centers, fostering the interfacial charge transfer and catalytic activity. Based on this mechanism, we obtain apparent correlations between biaxial strain and apparent activation energy for sulfur species conversion. This d-p hybridization dominated catalytic mechanism leads to obvious enhancement in capacity retention and rate performance. We showcase a 6 Ah-level multilayer pouch cell with a specific energy of 396 Wh kg–1 (based on masses of all components).
- Open Access
- 1 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (32) , 28820-28830
Balanced Iodophilicity and Solvophilicity Unlocks Fast Iodine Conversion Chemistry
The shuttling of polyiodides and sluggish redox kinetics greatly hinder the implementation of an aqueous Zn-I2 battery. Despite numerous catalysts have been implemented to improve the iodine cathode stability, an important aspect, the balance between polyiodide adsorption and interfacial mass transport kinetics at the cathode surface, has been overlooked. It is known that insufficient intermediate trapping ability will cause low iodine utilization and fast capacity decay. However, excessive adsorption of iodine species will block the ion transport and lead to passivation of the catalyst, which is particularly serious under lean-electrolyte and high mass loading conditions. To tackle this challenge, we employ a dual single atomic catalyst encompassing NiN4P and FeN4P sites to promote a catalytic interface with well-balanced solvophilicity and iodophilicity. Specifically, the FeN4 and NiN4 sites primarily enhance polyiodide immobilization and mass transport, respectively. The P ligands further strengthen these functions by tuning the Fe site from low to medium spin state and creating the anion-rich inner Helmholtz plane at Ni sites. Benefiting from this dual-metal atomic catalyst, the iodine cathode exhibits high cycling stability and ultralow self-discharge rate under a low E/I ratio. This work provides insights into regulating the aqueous halogen cathode interface for long cycle life.
- 1 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (32) , 28820-28830
Open AccessBalanced Iodophilicity and Solvophilicity Unlocks Fast Iodine Conversion Chemistry
The shuttling of polyiodides and sluggish redox kinetics greatly hinder the implementation of an aqueous Zn-I2 battery. Despite numerous catalysts have been implemented to improve the iodine cathode stability, an important aspect, the balance between polyiodide adsorption and interfacial mass transport kinetics at the cathode surface, has been overlooked. It is known that insufficient intermediate trapping ability will cause low iodine utilization and fast capacity decay. However, excessive adsorption of iodine species will block the ion transport and lead to passivation of the catalyst, which is particularly serious under lean-electrolyte and high mass loading conditions. To tackle this challenge, we employ a dual single atomic catalyst encompassing NiN4P and FeN4P sites to promote a catalytic interface with well-balanced solvophilicity and iodophilicity. Specifically, the FeN4 and NiN4 sites primarily enhance polyiodide immobilization and mass transport, respectively. The P ligands further strengthen these functions by tuning the Fe site from low to medium spin state and creating the anion-rich inner Helmholtz plane at Ni sites. Benefiting from this dual-metal atomic catalyst, the iodine cathode exhibits high cycling stability and ultralow self-discharge rate under a low E/I ratio. This work provides insights into regulating the aqueous halogen cathode interface for long cycle life.
- Top Cited Papers
- 22 July 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (30) , 26889-26897
Deciphering SN2-Type Nucleophilic Substitution via Halogen-Free Intermediates for High-Energy Zinc–Iodine Batteries
High-valence halogen conversion reactions are promising for realizing high-energy-density aqueous batteries. It has been more challenging to realize a stable and reversible I0/I+ conversion than the facile I-/I0 conversion. While interhalogen chemistry has been employed to realize a reversible I-/I0/I+ (i.e., four-electron) redox couple, the introduction of additional halide species raises corrosion and toxicity issues. Herein, we propose an SN2-type nucleophilic substitution mechanism for the activation of the I0/I+ redox process. A series of halogen-free intermediates containing imide groups is proven effective in promoting four-electron halogen reactions due to conjugation-stabilized nitrogen anions. A structure-kinetics relationship among various imide-containing molecules is elucidated using two descriptors: the hydrogen dissociation energy (Ed) of the imide group and the local nucleophilicity (LN) of the corresponding nitrogen anion. A Zn-I2 battery with a theobromine intermediate exhibits stable cycling (a capacity retention of 93.9% at 5 A g-1 over 1000 cycles). This work provides new insights into the mechanism of the I0/I+ redox process and a new avenue to the development of high-capacity multielectron iodine cathodes.
- 22 July 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (30) , 26889-26897
Top Cited PapersDeciphering SN2-Type Nucleophilic Substitution via Halogen-Free Intermediates for High-Energy Zinc–Iodine Batteries
High-valence halogen conversion reactions are promising for realizing high-energy-density aqueous batteries. It has been more challenging to realize a stable and reversible I0/I+ conversion than the facile I-/I0 conversion. While interhalogen chemistry has been employed to realize a reversible I-/I0/I+ (i.e., four-electron) redox couple, the introduction of additional halide species raises corrosion and toxicity issues. Herein, we propose an SN2-type nucleophilic substitution mechanism for the activation of the I0/I+ redox process. A series of halogen-free intermediates containing imide groups is proven effective in promoting four-electron halogen reactions due to conjugation-stabilized nitrogen anions. A structure-kinetics relationship among various imide-containing molecules is elucidated using two descriptors: the hydrogen dissociation energy (Ed) of the imide group and the local nucleophilicity (LN) of the corresponding nitrogen anion. A Zn-I2 battery with a theobromine intermediate exhibits stable cycling (a capacity retention of 93.9% at 5 A g-1 over 1000 cycles). This work provides new insights into the mechanism of the I0/I+ redox process and a new avenue to the development of high-capacity multielectron iodine cathodes.
- 14 July 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (2)
Silane‐Modified Zn Anode Induced (100) Plane Preferential Nucleation Enables Stable Aqueous Zn Batteries
Detrimental dendrite growth and water‐involved surface corrosion on Zn anode significantly hinder the aqueous Zn batteries implementation. Herein, Triacetoxy(vinyl)silane (VTSE) is employed as an etchant and a protective layer for Zn metal anode. Owing to the preferential adsorption of VTSE on Zn (002) and (101) planes, the treated Zn anode exhibits highly exposure of (100) facet with VTSE coverage. Such VTSE layer with strong Zn─Si─O interaction guides homogeneous Zn 2+ deposition with a good inheritance of (100) plane orientation, further bringing about a reduced nucleation overpotential and accelerated desolvation process. Meanwhile, the dense VTSE layer inhibits the water penetration and suppresses hydrogen evolution corrosion. As expected, the Zn||Cu half cell exhibits prolonged lifespan over 1000 h at 1 mA cm −2 for 1 mAh cm −2 .In the Zn||NVO full cell, a remarkable capacity retention of 73.1% can be reached after 2,000 cycles at 1 A g −1 . This work offers new insights on the crystal plane manipulation engineering for aqueous Zn anode protection.
- 14 July 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (2)
Silane‐Modified Zn Anode Induced (100) Plane Preferential Nucleation Enables Stable Aqueous Zn Batteries
Detrimental dendrite growth and water‐involved surface corrosion on Zn anode significantly hinder the aqueous Zn batteries implementation. Herein, Triacetoxy(vinyl)silane (VTSE) is employed as an etchant and a protective layer for Zn metal anode. Owing to the preferential adsorption of VTSE on Zn (002) and (101) planes, the treated Zn anode exhibits highly exposure of (100) facet with VTSE coverage. Such VTSE layer with strong Zn─Si─O interaction guides homogeneous Zn 2+ deposition with a good inheritance of (100) plane orientation, further bringing about a reduced nucleation overpotential and accelerated desolvation process. Meanwhile, the dense VTSE layer inhibits the water penetration and suppresses hydrogen evolution corrosion. As expected, the Zn||Cu half cell exhibits prolonged lifespan over 1000 h at 1 mA cm −2 for 1 mAh cm −2 .In the Zn||NVO full cell, a remarkable capacity retention of 73.1% can be reached after 2,000 cycles at 1 A g −1 . This work offers new insights on the crystal plane manipulation engineering for aqueous Zn anode protection.
- 13 May 2025
- Published by Wiley in Small Methods
- Vol. 10 (2) , e2500445
CMOS‐Compatible Protonic Three‐Terminal Memristor for Analog Synapse in Neuromorphic Computing
All‐solid‐state inorganic hydrogen‐based three‐terminal memristors (H‐3TMs) suffer from poor retention, susceptibility to humidity and temperature, and the reliance on wet chemistry during fabrication, hindering their manufacturability within existing foundry processes. To address these, this study presents a CMOS‐compatible H‐3TM based on reversible intercalation and extraction of protons between the SiN x electrolyte and WO x channel. The protons are introduced via a straightforward hydrogen plasma treatment, promoting a compatible fabrication process with back‐end‐of‐line integration. Experimental and simulation results indicate that the low proton transport tendency across the electrolyte/channel interface without an external electric field contributes to high retention performance. Furthermore, the device demonstrates linear potentiation and depression, 512 conductance states with a dynamic range of ≈40, low energy operation (≈73 fJ per write), and excellent overall device‐to‐device variation. Its analog properties are evaluated under the training and inference framework of MNIST and Fashion‐MNIST datasets. The device achieved training and inference accuracies only 0.4% and 0.3% below the ideal benchmark on the F‐MNIST dataset. This work offers a rational approach for future artificial synaptic device design and fabrication.
- 13 May 2025
- Published by Wiley in Small Methods
- Vol. 10 (2) , e2500445
CMOS‐Compatible Protonic Three‐Terminal Memristor for Analog Synapse in Neuromorphic Computing
All‐solid‐state inorganic hydrogen‐based three‐terminal memristors (H‐3TMs) suffer from poor retention, susceptibility to humidity and temperature, and the reliance on wet chemistry during fabrication, hindering their manufacturability within existing foundry processes. To address these, this study presents a CMOS‐compatible H‐3TM based on reversible intercalation and extraction of protons between the SiN x electrolyte and WO x channel. The protons are introduced via a straightforward hydrogen plasma treatment, promoting a compatible fabrication process with back‐end‐of‐line integration. Experimental and simulation results indicate that the low proton transport tendency across the electrolyte/channel interface without an external electric field contributes to high retention performance. Furthermore, the device demonstrates linear potentiation and depression, 512 conductance states with a dynamic range of ≈40, low energy operation (≈73 fJ per write), and excellent overall device‐to‐device variation. Its analog properties are evaluated under the training and inference framework of MNIST and Fashion‐MNIST datasets. The device achieved training and inference accuracies only 0.4% and 0.3% below the ideal benchmark on the F‐MNIST dataset. This work offers a rational approach for future artificial synaptic device design and fabrication.
- 28 April 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (30)
Chelation Effect Induced Robust Biomass Protective Layer for Aqueous Zn Metal Anode
The detrimental dendrite growth and hydrogen evolution corrosion on Zn metal anode greatly hinder the implement of aqueous zinc batteries. Constructing a stable solid electrolyte interphase (SEI) on Zn anode is considered an effective strategy to prolong the cells life. Herein, by using poly(N‐[2‐(3,4‐dihydroxyphenyl)ethyl]‐2‐methylacrylamide) (PDMA) as a case study, the impact of Zn2+ chelation effect on SEI layer generation is systematically investigated. The DMA monomer tends to form a robust PDMA layer on Zn anode with a higher crosslinking degree with the assistant of Zn2+. The Zn─O interaction between Zn metal and PDMA guarantees the long‐term protection efficiency of the SEI layer and uniformizes the Zn nucleation. Moreover, the Zn2+ desolvation can be propelled by the zincophilic hydroxyl groups in PDMA. As expected, the Zn symmetric cell with in‐PDMA showcases an extended lifespan of over 3800 h. The Zn||NVO full cell maintains a capacity of 150 mAh g−1 after 1000 cycles at 1 A g−1. This work is believed to guide the future aqueous Zn anode design based on the protective layer engineering.
- 28 April 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (30)
Chelation Effect Induced Robust Biomass Protective Layer for Aqueous Zn Metal Anode
The detrimental dendrite growth and hydrogen evolution corrosion on Zn metal anode greatly hinder the implement of aqueous zinc batteries. Constructing a stable solid electrolyte interphase (SEI) on Zn anode is considered an effective strategy to prolong the cells life. Herein, by using poly(N‐[2‐(3,4‐dihydroxyphenyl)ethyl]‐2‐methylacrylamide) (PDMA) as a case study, the impact of Zn2+ chelation effect on SEI layer generation is systematically investigated. The DMA monomer tends to form a robust PDMA layer on Zn anode with a higher crosslinking degree with the assistant of Zn2+. The Zn─O interaction between Zn metal and PDMA guarantees the long‐term protection efficiency of the SEI layer and uniformizes the Zn nucleation. Moreover, the Zn2+ desolvation can be propelled by the zincophilic hydroxyl groups in PDMA. As expected, the Zn symmetric cell with in‐PDMA showcases an extended lifespan of over 3800 h. The Zn||NVO full cell maintains a capacity of 150 mAh g−1 after 1000 cycles at 1 A g−1. This work is believed to guide the future aqueous Zn anode design based on the protective layer engineering.