Dae-Seob Song
Research Subjects
Research Interests
Dae-Seob Song has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Sung-Hoon Ahn
Seoul National University
4 shared publications Ji Ho Jeon
Institute of Advanced Machines and Design, Seoul National University, Seoul, Republic of Korea
2 shared publicationsEsther Gil
Department of Mechanical Engineering
1 shared publicationGeun-Young Kim
George W. Woodruff School of Mechanical Engineering
1 shared publication- Jae-Kyung Heo
Department of Mechanical Engineering, Seoul National University, Seoul, Republic of Korea
1 shared publication - Ji-Hyeon Song
Department of Mechanical Engineering Dankook University Yongin‐si South Korea
1 shared publication
Latest Publications
- 9 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (16) , 24200-24207
One-Step Fabrication of Packaged Glass Microheater Using Selective Laser Welding
The increasing demand for miniaturized and versatile microdevices has driven advancements in micropatterning technologies; however, packaging considerations are often overlooked or addressed with basic additions. This study introduces a new selective laser welding process facilitated by a silver (Ag) thin film, enabling simultaneous micropatterning and packaging in a single step. In the proposed method, the Ag thin film serves as a laser absorber in the welded area, where it transitions to a fully insulating state, while in the unwelded areas, the remaining Ag thin film serves as an electrode without transitions. Mathematical modeling and heat transfer simulations were conducted to examine the laser energy transfer mechanism and determine the optimal thickness of the Ag thin film. Laser scan paths were designed for the Joule heating microheater and generated for subsequent selective laser welding. The designed microheater was fabricated and hermetically packaged between the glass substrates. Finally, a reusable cell culture tester was fabricated to demonstrate the practical applicability of the packaged glass microheater. The prototype was directly applicable to cell culture without requiring additional packaging. Moreover, it demonstrated consistent heating performance even after washing for reuse, indicating its feasibility for reusable devices. These results indicate that the proposed selective laser welding process, demonstrating the potential for advancing micropatterning and packaging technologies with diverse applications, is a promising approach for manufacturing packaged microdevices.
- 9 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (16) , 24200-24207
One-Step Fabrication of Packaged Glass Microheater Using Selective Laser Welding
The increasing demand for miniaturized and versatile microdevices has driven advancements in micropatterning technologies; however, packaging considerations are often overlooked or addressed with basic additions. This study introduces a new selective laser welding process facilitated by a silver (Ag) thin film, enabling simultaneous micropatterning and packaging in a single step. In the proposed method, the Ag thin film serves as a laser absorber in the welded area, where it transitions to a fully insulating state, while in the unwelded areas, the remaining Ag thin film serves as an electrode without transitions. Mathematical modeling and heat transfer simulations were conducted to examine the laser energy transfer mechanism and determine the optimal thickness of the Ag thin film. Laser scan paths were designed for the Joule heating microheater and generated for subsequent selective laser welding. The designed microheater was fabricated and hermetically packaged between the glass substrates. Finally, a reusable cell culture tester was fabricated to demonstrate the practical applicability of the packaged glass microheater. The prototype was directly applicable to cell culture without requiring additional packaging. Moreover, it demonstrated consistent heating performance even after washing for reuse, indicating its feasibility for reusable devices. These results indicate that the proposed selective laser welding process, demonstrating the potential for advancing micropatterning and packaging technologies with diverse applications, is a promising approach for manufacturing packaged microdevices.
- 22 February 2024
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 43 (11) , 1809-1830
Scaling effects of manufacturing processes and actuation sources on control of remotely powered micro actuators
Over the past decade, remotely powered micro actuators have gained increased attention for biomedical and environmental remediation applications, owing to their ability to access confined regions and the nonintrusive nature of control. Recent studies focus on improving the functionality and versatility of micro actuators through the development of new fabrication and actuation techniques. However, there is a possibility that a limited understanding of the scaling impact of various physical principles governing design and control has affected the successful implementation of such devices in practical scenarios. Thus, the main focus of this review is to evaluate the most widely utilized manufacturing methods and remote actuation sources in light of various characteristics such as resolution, productivity, shape complexity, actuation speed, actuation mode, operating medium, and so on. State-of-the-art developments in each type of manufacturing and actuation are introduced and delineated. Finally, the limitations of current devices are reviewed, and the future direction to enable the full potential of this field is provided.
- 22 February 2024
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 43 (11) , 1809-1830
Scaling effects of manufacturing processes and actuation sources on control of remotely powered micro actuators
Over the past decade, remotely powered micro actuators have gained increased attention for biomedical and environmental remediation applications, owing to their ability to access confined regions and the nonintrusive nature of control. Recent studies focus on improving the functionality and versatility of micro actuators through the development of new fabrication and actuation techniques. However, there is a possibility that a limited understanding of the scaling impact of various physical principles governing design and control has affected the successful implementation of such devices in practical scenarios. Thus, the main focus of this review is to evaluate the most widely utilized manufacturing methods and remote actuation sources in light of various characteristics such as resolution, productivity, shape complexity, actuation speed, actuation mode, operating medium, and so on. State-of-the-art developments in each type of manufacturing and actuation are introduced and delineated. Finally, the limitations of current devices are reviewed, and the future direction to enable the full potential of this field is provided.
- 3 June 2023
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 6 (12) , 10845-10852
Three-Dimensional Printing of Ag Nanoparticle Meshes for Antibacterial Activity
- 3 June 2023
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 6 (12) , 10845-10852
Three-Dimensional Printing of Ag Nanoparticle Meshes for Antibacterial Activity
- Open Access
- 20 May 2022
- Published by Elsevier in CIRP Annals
- Vol. 71 (1) , 161-164
Crackless glass through-structure fabrication with laser-induced backside wet etching using detachably bonded cover
- 20 May 2022
- Published by Elsevier in CIRP Annals
- Vol. 71 (1) , 161-164
Open AccessCrackless glass through-structure fabrication with laser-induced backside wet etching using detachably bonded cover