Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ignacio Arruego has a total of 501 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sensing winds on Mars: a new pathway toward local and global measurements

    by Franck Montmessin, Manish Patel, Ignacio Arruego, Thomas Gautier, François Forget, Claire Newman, Baptiste Chide, Pernelle Bernardi, Tanguy Bertrand, Daniel Toledo, et al.

    Understanding the Martian atmosphere requires direct, vertically resolved measurements of winds. Despite decades of orbital and in situ exploration, wind profiles remain poorly constrained, limiting our ability to validate general circulation models (GCMs), quantify dust-lifting mechanisms, and predict atmospheric variability relevant to entry, descent, and landing (EDL). Existing wind information relies primarily on surface sensors with limited spatial representativeness or on tracer tracking techniques using water vapor and clouds, both of which suffer from incomplete coverage and intrinsic ambiguities. To address this long-standing observational gap, we are developing two complementary Doppler wind lidars dedicated to profiling winds and aerosols in the Martian atmosphere: MADWIL (Mars Doppler Wind Lidar), designed for orbital observations, and MARBLL (Mars Boundary Layer Lidar), a compact surface-based system dedicated to the planetary boundary layer.Both instruments rely on the same Doppler lidar concept. While MADWIL operates at 532 and 1064 nm, MARBLL only uses the 532 nm wavelength. Both are optimized for backscatter from ubiquitous Martian dust aerosols. Winds are retrieved from the Doppler shift measured at 532 nm using a quadrichannel Mach–Zehnder interferometer (QMZ) spectral analyzer, enabling line-of-sight (LOS) wind retrievals with expected precision on the order of 1 m s⁻¹ and a LOS ambiguity range of approximately ±270 m s⁻¹. Simultaneous aerosol backscatter profiling at 1064 nm provides information on dust and cloud vertical distributions, with polarization-sensitive detection enabling discrimination between aerosol types.MADWIL has been preselected on ESA LightShip1 and is designed to provide global measurements of horizontal winds and aerosol backscatter from orbit. The instrument concept includes a multiwatt Nd:YAG laser transmitter, a co-aligned SiC telescope optimized to minimize solar background contamination, and a thermally controlled optical bench. MADWIL is expected to retrieve wind profiles from the surface up to ~60 km altitude, depending on atmospheric dust loading, with kilometer-scale vertical resolution. These measurements will constrain atmospheric circulation patterns, wave activity, and dust transport processes from local to planetary scales while providing key inputs for GCM validation and EDL studies.MARBLL applies this observational capability to the near-surface atmosphere by targeting the Martian boundary layer, where exchanges between the surface and atmosphere control dust lifting, turbulence, and diurnal circulation. The instrument is conceived as a compact and resource-efficient lidar suitable for landed platforms. By continuously profiling winds and aerosols in the first kilometers above the surface, MARBLL will provide unprecedented insight into boundary-layer dynamics and their coupling to the larger-scale circulation observed by MADWIL from orbit.A laboratory breadboard has been developed to validate the QMZ Doppler measurement principle and establish the performance prediction framework shared by both instruments. In parallel, an Observing System Simulation Experiment (OSSE) framework is under development using Mars climate model outputs and realistic aerosol scenarios to assess retrieval performance and support instrument trade-offs in laser energy, telescope aperture, and detector configuration.Together, MADWIL and MARBLL form a complementary observational strategy spanning the Martian atmosphere from the surface to the middle atmosphere. By combining global orbital mapping with continuous local boundary-layer profiling, these instruments would provide the first comprehensive vertically resolved wind dataset at Mars, establishing a transformational benchmark for understanding Martian atmospheric dynamics, aerosol transport, and climate variability.

  • Open Access

    Characterization of Martian atmospheric turbulence using irradiance measurements from MEDA Radiation and Dust Sensor (RDS)

    by Clara Lorenzo-Corvo, Daniel Toledo, Victor Apestigue, Ignacio Arruego, Raúl Rodríguez-Veloso, Asier Munguira, Germán M. Martínez, Ricardo Hueso, Mark T. Lemmon, José A. Rodríguez-Manfredi

    Dust plays a fundamental role in shaping the dynamics of the Martian atmosphere. By interacting with solar radiation through scattering and absorption, it modifies atmospheric heating rates at the surface and aloft, driving buoyancy and vertical mixing processes. These thermally induced gradients contribute to the development and modulation of turbulent motions across different atmospheric layers. In turn, turbulence influences the lifting, transport, and redistribution of dust particles, leading to a tightly coupled, non-linear feedback system between radiative forcing and atmospheric dynamics.The Radiation and Dust Sensor (RDS) [1], part of the Mars Environmental Dynamics Analyzer (MEDA) [2] payload onboard the Mars 2020 Perseverance rover, is a radiometer that measures downwelling solar irradiance at the surface across multiple spectral bands at a frequency of 1Hz. Rapid temporal fluctuations in the measured irradiance are associated with variations in dust concentration induced by atmospheric turbulence.Most previous studies of Martian atmospheric turbulence have relied on near-surface in situ measurements (e.g. wind and temperature sensors) substantially limiting our understanding of Martian turbulence at higher altitudes. In contrast, the RDS radiometric signal, shaped by scattering along the zenith-pointing optical path, is sensitive to dust fluctuations at different altitudes, thereby enabling access to turbulent processes that are otherwise difficult to observe directly. Here, we study RDS irradiance fluctuations time series to characterize their spectral properties in the context of atmospheric turbulence; we analyze inertial-range behavior and introduce a synthetic turbulence modeling framework that, by treating dust as a passive and perfect tracer, allows us to directly examine how the RDS signal responds to atmospheric turbulence. In particular, this approach makes it possible to assess how variations in turbulent behavior across different layers, together with the structure of the vertical atmospheric profile, influence both the fluctuations of the RDS signal and the characteristics of its inertial range. References:[1] Apestigue, V., et al. “Radiation and Dust Sensor for Mars Environmental Dynamic AnalyzerOnboard M2020 Rover”. Sensor 22.8 (2022): 2907.[2] Rodriguez-Manfredi, Jose Antonio, et al. “The Mars Enviromental Dynamics Analyzer, MEDA. A suite of enviromental sensors for the Mars 2020 mission.” Space science reviews 217.3 (2021): 1-86.

  • Open Access

    H2S Cloud Properties in Uranus and Neptune: Sensitivity to Deep Composition and Vertical Mixing

    by Daniel Toledo, Pascal Rannou, Patrick Irwin, Michael Roman, Bruno de Batz de Trenquelléon, Raul Rodriguez-Veloso, Clara Lorenzo-Corvo, Víctor Apéstigue, Marco Personat, Ignacio Arruego

    Radiative transfer analyses of Uranus and Neptune spectra have revealed a cloud layer at pressures greater than ~2 bar (1,2), with H₂S gas detected above it on both planets (3,4), suggesting H₂S ice as its main constituent. However, the properties of these clouds and their dependence on the deep atmospheric composition remain poorly constrained.We present an extended version of a one-dimensional cloud microphysics model [5,6] previously applied to simulate CH₄ and H₂S clouds in the Ice Giants (7,8). The model now incorporates NH₄SH chemistry, extending the simulation domain to ~50 bar. Since NH₃ reacts with H₂S to form NH₄SH at depth, the deep N/S ratio controls how much H₂S is available to condense at higher altitudes. We explore how the deep NH₃ and H₂S abundances, together with the vertical mixing profile, determine the properties of the H₂S cloud layer, including its base pressure, total opacity, and particle size distribution.Preliminary results and the implications of this work for the interpretation of current and future observations of Uranus and Neptune will be discussed.References: [1] P. G. Irwin, et al., JGR: Planets, 127, e2022JE007189. [2] L. Sromovsky, et al., Icarus,Volume 317, (2019) [3] P. G. Irwin, et al., Nature Astronomy 2, 420 (2018). [4] P. G. Irwin, et al., Icarus 321, 550 (2019). ). [5] P. Rannou, et al., Science 311, 201 (2006). [6] F. Montmessin, et al., JGR: Planets 107, 4 (2002). [7] D. Toledo, et al., A&A, 694, A81 (2025). [8] D. Toledo, et al.,: Microphysical Modeling of Hydrogen Sulfide Clouds in the Atmospheres of the Ice Giants, EPSC-DPS Joint Meeting 2025, https://doi.org/10.5194/epsc-dps2025-1456, 2025.

  • Open Access

    Aerosol Optical Properties and Dust Deposition as observed by MEDA Radiation and Dust Sensor (RDS) at Jezero Crater, Mars

    by Raúl Rodriguez-Veloso, Daniel Toledo, Víctor Apestigue, Ignacio Arruego, Clara Lorenzo-Corvo, Germán M. Martínez, Mark T. Lemmon, Juan J. Jiménez-Martín, Elisa García-Menéndez, Ricardo Hueso, et al.

    Aerosols on Mars are a primary element for studying the interaction between the solar radiation and the atmosphere and surface. Depending on properties such as aerosol number density, particle radius, or refractive index, the aerosols can provide positive or negative radiative feedbacks on the atmospheric dynamics. Previous studies have revealed large temporal and spatial variability in the aerosol optical properties, emphasizing the need for continuous monitoring throughout the day and at multiple locations. To address these measurements, the Radiation and Dust Sensor (RDS) [1] was included as part of the Mars Environmental Dynamics Analyzer (MEDA) [2] payload onboard the Perseverance rover of the Mars 2020 mission. The RDS instrument is composed of two sets of eight photodiodes (RDS-DP) and a sky-pointed camera (RDS-SkyCam). One set, oriented toward the zenith, captures radiation from 190 to 1200 nm, while the other, inclined 20° above the horizon at 45° azimuthal intervals, samples a single wavelength. The analysis of these observations, through a radiative transfer model [3], allows for the retrieval of key aerosol parameters such as aerosol opacity at different wavelengths and particle radius. However, the continuous deposition of dust over the sensors [4], since the beginning of the mission, introduces modifications in their optical response. In particular, the zenith-pointed photodiodes require angular response calibration due to the progressive accumulation of dust on their optical surfaces. Here, we present the calibration approach developed for the mission, essential to ensure the accuracy of aerosol property retrievals and reliable long-term atmospheric monitoring. Figure 1 shows the temporal evolution of the RDS-TOP 7 irradiance change derived from our calibration alongside Matscam-Z opacities [5], highlighting the impact of atmospheric conditions. In addition, we report ongoing radiative transfer retrievals of aerosol (dust and ice) optical properties during the first two years of the Mars 2020 mission. The relationship between vortex population and dust deposition rates will also be discussed.Figure 1. Temporal evolution of the irradiance change measured by MEDA-RDS TOP 7 (blue) of the Mars 2020 mission at Jezero Crater, compared with atmospheric opacity at 630 nm measured by Mastcam-Z (red) over the first two years.References:[1] Apestigue, V., et al. “Radiation and Dust Sensor for Mars Environmental Dynamic AnalyzerOnboard M2020 Rover”. Sensor 22.8 (2022): 2907.[2] Rodriguez-Manfredi, Jose Antonio, et al. “The Mars Enviromental Dynamics Analyzer, MEDA. A suite of enviromental sensors for the Mars 2020 mission.” Space science reviews 217.3 (2021): 1-86.[3] Toledo, D., et al. “Measurement of aerosol optical depth and sub-visual cloud detection using the optical depth sensor (ODS)”. Atmospheric Measurement Techniques 9.2 (2016): 455-467.[4] Vicente-Retortillo, A., et al. “Dust Accumulation and Lifting at the Landing Site of the Mars 2020 Mssion, Jezero Crater, as Observed From MEDA.” Geophysical Research Letters 51 (2024).[5] Lemmon, M. T. Et al. “Dust, sand and winds within an active Martian storm in Jezero crater.” Geophysical Research Letters, 49.17 (2022): 0094-8276.

  • Open Access

    HARPOON mission — Hydration And Regolith Penetration Observatory On Mars —: scientific objectives and sensor suite

    by Daniel Toledo, Ignacio Arruego, Víctor Apéstigue, MarsConnect and HARPOON teams

    Understanding the present-day behavior of water on Mars, including atmosphere–subsurface exchange processes, the possible formation of transient brines, and the stability of shallow subsurface ice, remains one of the major open questions in planetary science. HARPOON (Hydration And Regolith Penetration Observatory On Mars) is a mission concept aimed at investigating how water actively exchanges between the Martian atmosphere and subsurface, and to what extent these processes may lead to the formation of transient liquid phases under present-day Martian conditions. The mission is based on the deployment of a reduced network of penetrator-type probes [1] at different latitudes on Mars, enabling simultaneous atmospheric and subsurface measurements over diurnal and seasonal timescales. Previous presentations of the HARPOON mission focused primarily on the overall mission concept, penetrator architecture, and technical implementation [2]. The present work instead focuses on the scientific objectives of the mission, the proposed atmospheric and subsurface sensor suite, and the mission configurations required to achieve these objectives, including the evaluation of trade-offs associated with the number of probes, latitudinal deployment, measurement sampling strategies, and operational periods needed to characterize water exchange processes and potential transient brine formation on Mars.REFERENCES:[1] Ignacio Arruego et al., “Mars environmental networks through the MarsConnect microprobes”, EPSC Abstracts, Vol. 17, EPSC2014-92.[2] Arruego, I., Apéstigue, V., and Toledo, D. and the MarsConnect and HARPOON teams: HARPOON mission concept: Hydration And Regolith Penetration Observatory On Mars, EPSC-DPS Joint Meeting 2025, Helsinki, Finland, 7–12 Sep 2025, EPSC-DPS2025-1604, https://doi.org/10.5194/epsc-dps2025-1604, 2025.

  • Open Access

    Albedo and Thermal Inertia at Jezero Crater from MEDA over the First 1600 Sols: Extended Analysis and Calibration Improvements

    by Alvaro Vicente-Retortillo, German Martínez, Eduardo Sebastián, Mark Lemmon, Raúl Rodríguez-Veloso, Daniel Toledo, Víctor Apéstigue, Ignacio Arruego, José Antonio Rodríguez-Manfredi

    IntroductionThe surface albedo and thermal inertia are key parameters to understand the climate and geology of Mars. Albedo controls the amount of solar energy that is absorbed by the surface, playing an important role in the Surface Energy Budget (SEB), which on Mars is controlled by the radiative terms [1]. The SEB and the surface thermal inertia determine the temporal evolution of the ground temperature, which in turn drives the near-surface atmospheric processes. In addition, surface albedo and thermal inertia allow the geological characterization of the terrain, as they depend on rock abundance, particle size or porosity.The MEDA instrument [2] onboard the Perseverance rover of the Mars 2020 mission includes the Radiation and Dust Sensor (RDS) [3] and the Thermal InfraRed Sensor (TIRS) [4], among other sensors, which allow the direct determination of these parameters.Methodology and Calibration ImprovementsSurface albedo is obtained from downward and upward shortwave fluxes, which are obtained respectively from the RDS TOP-7 and TIRS-IR3 channels. The retrieval of the thermal inertia uses also the surface brightness temperature measured by the TIRS-IR5 and the surface energy budget, in which the downward and upward longwave fluxes are obtained respectively from the TIRS-IR1 and TIRS-IR4 channels.This work expands and improves the results presented in [1] covering the first 350 sols of the mission. In order to accurately perform longer-term analyses, such as this one, it becomes necessary to correct RDS and TIRS measurements for the effect of dust accumulation. This is done by means of a Dust Correction Factor (DCF). In this work we use recent correction factors for dust deposition on the RDS [5] and TIRS [6] channels, which improve the accuracy of the radiative terms, which in turn allow for a refinement in the calculation of the surface albedo and thermal inertia.Figure 1 shows the DCF on the RDS TOP-7 channel. The temporal evolution shows two periods of strong net dust accumulation, between sols 400-600 and 1000-1200, covering slightly more than the first half of the perihelion season. During the remaining periods, dust accumulation experiences little variability. Finally, net dust removal occurs at the end of the analyzed period.Figure 1. Dust Correction Factor for the RDS TOP-7 channel.Figure 2 shows the DCF on the TIRS channels. Dust accumulation is small for the last three channels because they are looking downwards. The behavior of IR1 and IR2 is similar to that of the RDS TOP-7, but with a smaller effect of dust accumulation, particularly on the IR1 channel.Figure 2. Dust Correction Factor for the TIRS channels.ResultsFigure 3 shows the surface albedo during the first 1,600 sols of the mission. Surface albedo strongly depends on illumination and viewing geometry, leading to a significant diurnal variation [1]. For this reason, we show the values at noon, which represent the diurnal minimum. The temporal evolution appears to show a seasonal cycle, with minimum values at around Ls = 180º and maximum values at around Ls = 270º. The values range from 0.10 to 0.23, and the surface albedo in MY 37 appears to be systematically larger than in MY 36.Figure 3. Surface albedo at Noon for the first 1,600 sols. Vertical lines indicate Ls = 180º and Ls = 270º for MY 36 and 37. Figure 4 shows the surface thermal inertia during the first 1,600 sols of the mission. Contrary to the albedo, the temporal evolution is now controlled by the portion of the terrain observed by TIRS, and a seasonal cycle is not clearly identified. The strong fluctuations can be attributed to the relatively small field of view of TIRS, which observes an area of approximately 3-4 m2, and therefore it is very sensitive to surface heterogeneities. Values range from below 200 to above 600 SI units, indicating a variety of terrain features.Figure 4. Surface thermal inertia for the first 1,600 sols.DiscussionThese results can be compared to those obtained from satellite observations. In the case of thermal inertia, THEMIS retrievals [7] around the rover traverse are tipically between 200 and 400 SI units. The smaller range of values can be attributed to the different spatial resolutions of both instruments.Mean values from OMEGA albedo observations [8] for the region where Perseverance is located are around 0.16, in very good agreement with MEDA retrievals. OMEGA observations (Figure 5) also show higher albedo values as the rover moved towards the West, in agreement with MEDA retrievals. Furthermore, the seasonal cycle observed from MEDA is consistent with that observed at Syrtis Major from MARCI observations for MY 28 to 33, with annual minima around Ls = 180º and maxima around Ls = 270º [9]. The increase in brightness is approximately coincident with the strong decreases of the RDS DCF, suggesting that it can be partially attributed to dust deposition.Figure 5. OMEGA albedo values, with the rover traverse shown in black.The presented results are important to validate numerical models and provide ground-truth for satellite observations of albedo and thermal inertia. In addition, these results include the area named Three Forks, where ten sample tubes have been deposited. Finally, they allow exploring the role of dust storms and dust lifting and deposition on these parameters throughout the mission.AcknowledgementsThis research is funded by the Spanish Ministry of Science, Innovation and Universities (MICIU)/State Agency of Research (AEI) project PID2024-161247OB-C31, funded by MICIU/AEI /10.13039/501100011033 / FEDER, UEReferences[1] Martínez, G. M. et al. (2023). Journal of Geophysical Research: Planets, 128, e2022JE007537. [2] Rodríguez-Manfredi, J. A. et al. (2021). Space Science Reviews, 217(3), 1–86. [3] Apéstigue, V. et al. (2022). Sensors, 22(8), 2907. [4] Sebastián, E. et al. (2020). Measurement, 164, 107968. [5] Vicente-Retortillo, A. et al. (2024)....

  • Open Access

    Novel concept for light-direction sensors based on the wave nature of light

    by Michelle Cedeño Mata, Ignacio Arruego, Juan J. Jiménez, Sandra Bermejo, Moises Garin

    Sun sensors are designed to detect and measure both the intensity and direction of light. They play a key role in fields such as renewable energy, optics, and aerospace, where the ability to detect the angle of incidence of light has multiple applications. For example, in energy systems, the sun sensors are used in solar trackers to optimise the orientation of solar panels. In optics, they help align light beams within precision systems, and in the aerospace sector, light-angle sensors are used for attitude determination and control [1][2].Traditionally, conventional sun sensors work by relying on geometric principles, using the ray approximation of light to detect its direction [3]. In such systems, angular sensitivity is reached by projecting light through different occlusive elements onto photodetectors. The most basic approach employs a planar photodetector whose signal varies with the cosine of the incidence angle, providing only coarse resolution. More advanced designs include four-quadrant detectors or CMOS technology with internal walls that cast angle-dependent shadows [4][5], while digital alternatives use arrays of photodetectors that are exposed through aligned apertures or slits to determine direction [6][7]. Other methods include waveguides that react to both direction and wavelength, resonant filters based on diffraction, or microstructures that selectively block or transmit light [8]. Despite their wide use, conventional light-angle sensors face multiple limitations. Several sun sensors require bulky, precisely aligned optical components. Geometric method-based sun sensors present a trade-off between angular resolution and field of view, while digital sensors frequently underuse the active area. Resonant filter-based systems are usually sensitive to certain wavelengths, which restricts their applicability to broadband light sources. Consequently, current designs often reveal trade-offs between accuracy, reliability, compactness, and cost. In this view, this work presents the analysis and development of a novel light-angle sensor that addresses the limitations of traditional sun sensors by exploiting the wave nature of light [9]. The angular dependence of the transmittance spectrum through an interferent optical layer is the basis of the proposed concept. This effect can be attained through engineered structures such as diffraction braggs, gratings, metasurfaces, or rugate filters [10-13]. This angularly modulated spectral response enables compact and high-resolution sensing without the need for external optics.Figure 1: Representation of the measurement principle: a) angle dependence of transmission band in an interference filter, b) Transmission spectra sampled through different sensing elements featuring different coloured filters (angle-independent), and c) Representation of a device sensible to both, elevation and azimuth angles. The device would use an array of elements combining different coloured and interference filters. Figure 1 provides a conceptual illustration of the sensor, which consists of two main components: the interference filter and coloured absorptive filters. When source light interacts with the interferent layer, a specific transmittance pattern is generated, which varies as the angle of incidence changes. This modulated light then passes through the coloured filters, each of which transmits a specific wavelength band to a corresponding photodetector. Depending on the received transmittance distribution, the photodetectors generate different signal levels and, by comparing these signals, the system can accurately determine the direction of the incoming light. Therefore, the interferent filter is the primary sensing component, as it translates the angle of incidence into a unique spectral pattern, while coloured filters isolate specific wavelength regions, allowing each photodetector to respond differently depending on the incidence angle, converting angular information into measurable spectral variations. Figure 2 illustrates this principle through a simulated unpolarised transmittance spectrum of a TiO2-Al2O3 bragg-based structure, which clearly shows angle-dependent spectral features, and two commercial colour-filtered photodetectors. In particular, Figure 2a shows the transmittance as a function of wavelength and incidence angle, overlaid with the spectral response curves of red and blue filters. Based on the interaction of the generated transmittance spectrum and the sensitivity of each filter, Figure 2b displays the resulting electrical signals of the photodetectors. Finally, Figure 2c exhibits sensing response of the proposed sun sensor. In particular, this figure shows the relative change between both signals across the angular range, which reveals a monotonic response. The obtained behaviour confirms that the chosen combination of the bragg-based structure and coloured filters enables accurate, continuous, and high-resolution light-angle detection, validating the viability of the proposed sensor concept. Figure 2: Interferential light-angle sensor response: a) Real coloured-filters response vs. Unpolarized transmittance spectrum of a particular interference filter structure, b) Response of photodetectors to the interaction between coloured filters and the incidence-angle-dependent spectrum of the interferent element, and c) Relative change revealed by the complete sensor.In conclusion, this work presents a first insight into a new light-direction sensing approach based on wave optics. By combining an angle-sensitive interferent filter with colour-selective detection, the proposed sensor offers a promising balance of compactness, accuracy, robustness, cost-effectiveness, integration potential, and angle estimation without the need for bulky optics or complex alignment. Simulations confirm the feasibility of the concept and its potential for integration into next-generation light-direction detectors. Future work will focus on experimental...

  • Open Access

    Evidence of an enhanced near-surface ozone layer at tropical latitudes on Mars

    by Daniel Viúdez-Moreiras, Michael D. Smith, Mike Wolff, Megan A. J. Brown, Frank Daerden, María-Paz Zorzano, Víctor Apestigue, Ignacio Arruego, Elisa García, Juan J. Jiménez, et al.

    Ozone plays a key role in both atmospheric and near-surface chemistry, as well as in UV absorption in planetary atmospheres. Here, we report observations of ozone from the surface of another planet, using the ozone detector included in the Mars Environmental Dynamics Analyzer (MEDA) Radiation and Dust Sensor (RDS) aboard NASA’s Mars 2020 mission, complementing previous space-based and ground-based observations from Earth. Measurements were acquired at Jezero Crater, Mars, at midday, retrieving an average ozone column abundance of 3.8 ± 2.3 μm-atm (1σ) around aphelion, which fell below uncertainties in northern summer. The retrieved column abundance is in reasonable agreement with previous space-based and ground-based observations from Earth. The measurements of total ozone column abundance around aphelion from Mars 2020 and other missions, together with vertical profile observations from orbit, indicate that ~90% of the observed ozone is confined below 20 km of altitude, the aphelion layer weakly contributing to the total column abundance. These ozone levels below 20 km are 3 to 4 times higher than those predicted by models, challenging current understanding of atmospheric chemistry and composition in the lower atmosphere of Mars. It may be possible that aerosols are reducing the destruction pathways of ozone and/or that unknown active chemistry in the near-surface atmosphere of Mars is at work. Both cases should strongly modify the oxidizing capacity in the lower atmosphere of Mars from current model predictions.


  • Open Access

    Lunar In-situ Navigation and Communication Node - LUNINA

    by Antti Kestilä, Harri Haukka, Ignacio Arruego, Ari-Matti Harri, Maria Genzer, Victor Apéstigue, Maria Hieta, Carmen Camañes, Cristina Ortega, Jarmo Kivekäs, et al.

    LUNINA is an in-situ navigation and communication node. The proposed platform is designed to be a compact, independent, cost effective, robust, and location independent navigation beacon and communication relay on the Moon that can operate 24/7. The design draws from the European Space Agency (ESA)-funded MiniPINS LINS platform [1], developed for long-term deployment in the Schrödinger crater but adaptable to other lunar environments with sufficient sunlight. Each LINS unit incorporates a Radioactive Heating Unit (RHU) to maintain functionality during the cold lunar night and uses solar panels and batteries for continuous power.LUNINA serves two primary purposes: navigation and communication. As a navigation aid, each node emits signals that support line-of-sight users on the surface and orbiting spacecraft, providing critical assistance for tasks such as landing and launch operations. When deployed at elevated locations, the nodes enhance surface navigation by offering precise positioning. For communication, LUNINA functions as a relay for data transfer between ground and orbit-based users. The elevated placement of nodes allows them to cover larger surface areas and relay messages through a network configuration. This capability supports both localized communication near lunar bases and broader applications across the Moon's surface.Figure 1: LUNINA nodes (in red dots) in Schrödinger crater around the Lunar Base (green dot).The platform functions as a durable communication and navigation network for lunar missions. The default payload for LUNINA is a communication system, which facilitates seamless integration into lunar infrastructure. Designed as a "drop and forget" solution, the system offers long-term reliability for safe and flexible lunar exploration.Figure 2: Different applications of the LUNINA node.The inclusion of an RHU would allow the thermalization of the in-situ LUNINA unit during the Lunar night, where energy storage need may lead to unaffordable battery volumes. Radioisotope power systems utilising americium-241 as a heat source fuel have been under development in Europe since 2009 as part of a European Space Agency funded programme [2].The LUNINA platform will support different navigation methods. Utilizing signals from multiple nodes enhances navigational accuracy for landing and launch operations. As part of the broader Lunar Communications and Navigation Services (LCNS) initiative, the system’s modular design allows for future upgrades to maintain compatibility with evolving infrastructure.Key Features:1. Compactness: Derived from the MiniPINS LINS platform.2. Independence: Capable of continuous 24/7 operation.3. Cost-Effectiveness: Using the heritage LINS, standardized parts and systems, the costs of development is minimized. Once node is developed, the node can be mass produced, bringing down its cost.4. Robustness and Modularity: Supports standardized interfaces and updatable software.5. Durability: Designed for long-term operation with upgradable software.6. Location Independence: Deployable anywhere on the Moon.References:[1] Genzer M., et al. "MiniPINS - Miniature Planetary In-situ Sensors," EGU General Assembly 2021, https://doi.org/10.5194/egusphere-egu21-11282.[2] Ambrosi et al., "European Radioisotope Thermoelectric Generators (RTGs) and Radioisotope Heater Units (RHUs) for Space Science and Exploration," Space Sci Rev 215, 55 (2019), https://doi.org/10.1007/s11214-019-0623-9.

  • Open Access

    The Uranus Multi-Experiment Radiometer for Haze and Clouds Characterization: development status

    by Víctor Apéstigue, Daniel Toledo, Ignacio Arruego, Umr Team

    The understanding of Uranus' atmosphere remains incomplete, primarily derived from ground-based observations, space telescope data, and the Voyager 2 flyby nearly three decades ago. The latest Decadal Survey [1] has highlighted a mission to Uranus as a top scientific priority, emphasizing the need for dedicated instruments to study its atmospheric composition, thermal structure, and cloud dynamics.The Uranus Multi-Experiment Radiometer (UMR) [2] is a lightweight, high-performance instrument designed for integration into the descent probe of this future mission [3]. Its primary objective is to investigate the vertical distribution of aerosols, including hazes and clouds, and their microphysical and scattering properties. These aerosols critically impact Uranus' energy balance, modulating solar radiation absorption and reflection.Despite the UMR building upon heritage from previous Mars exploration [4-6] missions, a dedicated technology readiness program has been launched to qualify all instrument technologies for the harsh environment they will endure during the mission. In this contribution, we will present the current status and advancements of this program, along with the detailed design of the instrument.