Chakrit Sirisinha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Chakrit Sirisinha has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
Pongdhorn Saeoui
MTEC, National Science and Technology Development Agency 114 Thailand Science Park, Paholyothin Rd, Klong 1 KlongLuang Pathumthani 12120 Thailand
13 shared publicationsPongdhorn Sae-Oui
MTEC, National Science and Technology Development Agency (NSTDA), 114 Thailand Science Park, Phahonyothin Road, Khlong Nueng, Khlong Luang, Pathum Thani 12120, Thailand
8 shared publicationsPongdhorn Sae‐Oui
MTEC National Science and Technology Development Agency Klong‐Luang Pathumthani Thailand
7 shared publications- Narongrit Sombatsompop
King Mongkut’s University of Technology Thonburi (KMUTT)
5 shared publications - Pongdhorn Sae-Oui
National Metal and Materials Technology Center (MTEC), National Science and Technology Development Agency (NSTDA), Khlong Nueng, Khlong Luang, Pathum Thani 12120, Thailand
4 shared publications Jantagarn Guaysomboon
Department of Chemistry, Faculty of Science, Mahidol University, Rama 6 Rd., Bangkok 10400, Thailand
3 shared publications
Latest Publications
- Open Access
- 25 May 2026
- Published by Elsevier in SSRN Electronic Journal
A sustainable natural rubber-based soft robotic finger with two-joint human-like flexion
Achieving human-like dexterity in soft robotic end-effectors remains a significant challenge, particularly in replicating the coordinated inter-joint motion of the human hand. This work presents a biomimetic two-joint soft robotic index finger that achieves anatomically inspired coupling between the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints through a simplified pneumatic architecture. The actuator is fabricated from vulcanized natural rubber (NR) latex via a gelling-assisted casting process, offering a sustainable and mechanically robust alternative to conventional silicone-based materials. By tailoring the pneumatic chamber geometry at each joint segment, the proposed design enables coordinated flexion and extension that mimics human finger kinematics. Experimental results reveal a consistent linear relationship between PIP and DIP flexion angles, with dominant bending at the PIP joint and an average distal coupling coefficient of 0.71, indicating strong inter-joint coordination. The influence of material stiffness on actuation performance is systematically investigated by varying crosslink density and chamber wall thickness. Softer configurations exhibit greater bending efficiency, sensitivity, and force output at lower actuation pressures, while stiffer configurations improve structural robustness and pressure tolerance. An optimized design achieves a balanced performance, delivering a maximum pressing force of 1.4 N and a lifting force of 6.27 N at 160 kPa. These results demonstrate that combining NR-based materials with geometrically encoded joint behavior provides an effective and scalable strategy for achieving biomimetic motion in soft robotic fingers, offering a sustainable solution for next-generation prosthetic, assistive, and human–robot interaction systems.
- 25 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA sustainable natural rubber-based soft robotic finger with two-joint human-like flexion
Achieving human-like dexterity in soft robotic end-effectors remains a significant challenge, particularly in replicating the coordinated inter-joint motion of the human hand. This work presents a biomimetic two-joint soft robotic index finger that achieves anatomically inspired coupling between the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints through a simplified pneumatic architecture. The actuator is fabricated from vulcanized natural rubber (NR) latex via a gelling-assisted casting process, offering a sustainable and mechanically robust alternative to conventional silicone-based materials. By tailoring the pneumatic chamber geometry at each joint segment, the proposed design enables coordinated flexion and extension that mimics human finger kinematics. Experimental results reveal a consistent linear relationship between PIP and DIP flexion angles, with dominant bending at the PIP joint and an average distal coupling coefficient of 0.71, indicating strong inter-joint coordination. The influence of material stiffness on actuation performance is systematically investigated by varying crosslink density and chamber wall thickness. Softer configurations exhibit greater bending efficiency, sensitivity, and force output at lower actuation pressures, while stiffer configurations improve structural robustness and pressure tolerance. An optimized design achieves a balanced performance, delivering a maximum pressing force of 1.4 N and a lifting force of 6.27 N at 160 kPa. These results demonstrate that combining NR-based materials with geometrically encoded joint behavior provides an effective and scalable strategy for achieving biomimetic motion in soft robotic fingers, offering a sustainable solution for next-generation prosthetic, assistive, and human–robot interaction systems.
- Open Access
- 14 May 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (20) , 20875-20885
Properties and Potential of Green Natural Rubber Composites Filled with Biofillers from Cassia bakeriana Craib and Cassia fistula L. Pods
This study investigates Cassia bakeriana (PS) and Cassia fistula (GS) pod powders as sustainable biofillers for natural rubber (NR), aiming to offer eco-friendly alternatives to conventional fillers. The powders were characterized and incorporated into NR to evaluate their effects on bound rubber content, cure behavior, cross-link density, and mechanical and dynamic properties. Both fillers were rich in organic components; cellulose, hemicellulose, lignin, proteins, and fatty acids with minor calcium oxalate and surface hydroxyl groups that promoted rubber–filler interaction. Nitrogen-containing compounds in the powders contributed to cure acceleration. GS powder outperformed PS in terms of scorch and cure times, hardness, modulus, and reinforcement, indicating more effective filler–rubber interaction. However, both fillers exhibited lower reinforcing efficiency than carbon black (CB), mainly due to their larger particle sizes. Tensile strength peaked at 20 phr for PS (20 MPa), about 11 and 22% lower than GS and CB, respectively. GS-filled composites also showed higher storage modulus and lower tan δ, suggesting greater stiffness and reduced energy loss. These results confirm that PS and GS powders can function as renewable, partially reinforcing fillers in NR, with GS offering superior mechanical and dynamic performance. Their use also shortens cure time and supports sustainable waste utilization. Given their moderate reinforcement and environmental benefits, PS and GS powders are suitable for noncritical rubber products such as shoe soles, mats, gaskets, and general-purpose molded goods, where cost efficiency and sustainability are prioritized over high-performance requirements.
- 14 May 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (20) , 20875-20885
Open AccessProperties and Potential of Green Natural Rubber Composites Filled with Biofillers from Cassia bakeriana Craib and Cassia fistula L. Pods
This study investigates Cassia bakeriana (PS) and Cassia fistula (GS) pod powders as sustainable biofillers for natural rubber (NR), aiming to offer eco-friendly alternatives to conventional fillers. The powders were characterized and incorporated into NR to evaluate their effects on bound rubber content, cure behavior, cross-link density, and mechanical and dynamic properties. Both fillers were rich in organic components; cellulose, hemicellulose, lignin, proteins, and fatty acids with minor calcium oxalate and surface hydroxyl groups that promoted rubber–filler interaction. Nitrogen-containing compounds in the powders contributed to cure acceleration. GS powder outperformed PS in terms of scorch and cure times, hardness, modulus, and reinforcement, indicating more effective filler–rubber interaction. However, both fillers exhibited lower reinforcing efficiency than carbon black (CB), mainly due to their larger particle sizes. Tensile strength peaked at 20 phr for PS (20 MPa), about 11 and 22% lower than GS and CB, respectively. GS-filled composites also showed higher storage modulus and lower tan δ, suggesting greater stiffness and reduced energy loss. These results confirm that PS and GS powders can function as renewable, partially reinforcing fillers in NR, with GS offering superior mechanical and dynamic performance. Their use also shortens cure time and supports sustainable waste utilization. Given their moderate reinforcement and environmental benefits, PS and GS powders are suitable for noncritical rubber products such as shoe soles, mats, gaskets, and general-purpose molded goods, where cost efficiency and sustainability are prioritized over high-performance requirements.
- Open Access
Effect of Repeated Autoclave on Hardness and Tensile Strength of Polypropylene/Natural Rubber Developed for Rubber Dam Clamp
In this study, we aimed to explore the feasibility of utilizing polypropylene (PP) and natural rubber (NR) blends as alternative materials for rubber dam clamps in dentistry. The hardness of various PP/NR blend ratios was compared to the commercial product SoftClampTM. Selected blend ratios exhibiting hardness values resembling rigid plastic were further evaluated for hardness and tensile strength after undergoing 1, 5, and 10 autoclave cycles. One-way ANOVA test results found that the PP/NR blends exhibited significantly lower hardness (p < 0.001) than the commercial SoftClampTM. PP/NR ratios of 100/0, 90/10, and 80/20 exhibited hardness levels equivalent to 82%, 80%, and 75% of SoftClampTM, respectively. Two-way ANOVA revealed significant reductions in hardness (p < 0.001) and tensile strength (p < 0.001) with increasing NR content across all autoclave cycles. However, post-autoclave assessments at 1, 5, and 10 cycles demonstrated no statistically significant differences in tensile strength (p = 0.058) and hardness (p = 0.52) for PP/NR ratios of 100/0, 90/10, and 80/20 compared to their pre-autoclave states. The NR content within the PP/NR blends decreased hardness and tensile strength, while autoclaving did not significantly affect the hardness and tensile strength of the PP/NR blends.
Open AccessEffect of Repeated Autoclave on Hardness and Tensile Strength of Polypropylene/Natural Rubber Developed for Rubber Dam Clamp
In this study, we aimed to explore the feasibility of utilizing polypropylene (PP) and natural rubber (NR) blends as alternative materials for rubber dam clamps in dentistry. The hardness of various PP/NR blend ratios was compared to the commercial product SoftClampTM. Selected blend ratios exhibiting hardness values resembling rigid plastic were further evaluated for hardness and tensile strength after undergoing 1, 5, and 10 autoclave cycles. One-way ANOVA test results found that the PP/NR blends exhibited significantly lower hardness (p < 0.001) than the commercial SoftClampTM. PP/NR ratios of 100/0, 90/10, and 80/20 exhibited hardness levels equivalent to 82%, 80%, and 75% of SoftClampTM, respectively. Two-way ANOVA revealed significant reductions in hardness (p < 0.001) and tensile strength (p < 0.001) with increasing NR content across all autoclave cycles. However, post-autoclave assessments at 1, 5, and 10 cycles demonstrated no statistically significant differences in tensile strength (p = 0.058) and hardness (p = 0.52) for PP/NR ratios of 100/0, 90/10, and 80/20 compared to their pre-autoclave states. The NR content within the PP/NR blends decreased hardness and tensile strength, while autoclaving did not significantly affect the hardness and tensile strength of the PP/NR blends.
- Open Access
- 13 November 2024
- Published by MDPI AG in Dentistry Journal
- Vol. 12 (11) , 361
The Flexural Strength and the Effect of the Autoclave Sterilization of Polypropylene/Natural Rubber Blended Materials
Background: Rubber dam clamps are used extensively in dentistry, especially during root canal treatment. However, existing rubber dam clamps have several drawbacks, including discomfort and potential damage to vital tissue in the oral cavity. To address these existing issues, a new rubber dam clamp should be developed. The aim of this study was to identify the optimum ratios of polypropylene and natural rubber (PP/NR) for a customized rubber dam clamp in dentistry. This study was focused on the flexural strength of PP/NR in various ratios. Moreover, the impact of autoclave sterilization was also considered. Methods: Six proportions of PP/NR blends (100/0, 90/10, 80/20, 70/30, 60/40 and 50/50) were prepared and assessed for flexural strength using a three-point bending test. After this test, the PP/NR blends with 100/0, 90/10 and 80/20 ratios were selected and underwent autoclave sterilization for 1, 5 and 10 cycles. Eventually, the flexural strength testing was repeated and investigated. An analysis of variance and Tukey’s test were used to evaluate the flexural strength of various PP/NR blends before autoclave sterilization at p < 0.05. An analysis of variance and Dunnett’s T3 test were used to evaluate the flexural strength of selected PP/NR blends before and after autoclave sterilization at p < 0.05. Results: The results revealed that the flexural strength of PP/NR blended materials showed a statistically significant difference in every group of this study. The autoclave sterilization test revealed that the flexural strength of the PP/NR 90/10 and 80/20 ratios was significantly increased after sterilization for 1, 5 and 10 cycles. In addition, the PP/NR 90/10 ratio was also comparable to the 100/0 ratio. The lower NR content in PP/NR blends resulted in significantly higher flexural strength, and autoclave sterilization had an effect on this property. Conclusions: This study suggested that the PP/NR blend with a 90/10 ratio might be considered as an alternative material for developing rubber dam clamps.
- 13 November 2024
- Published by MDPI AG in Dentistry Journal
- Vol. 12 (11) , 361
Open AccessThe Flexural Strength and the Effect of the Autoclave Sterilization of Polypropylene/Natural Rubber Blended Materials
Background: Rubber dam clamps are used extensively in dentistry, especially during root canal treatment. However, existing rubber dam clamps have several drawbacks, including discomfort and potential damage to vital tissue in the oral cavity. To address these existing issues, a new rubber dam clamp should be developed. The aim of this study was to identify the optimum ratios of polypropylene and natural rubber (PP/NR) for a customized rubber dam clamp in dentistry. This study was focused on the flexural strength of PP/NR in various ratios. Moreover, the impact of autoclave sterilization was also considered. Methods: Six proportions of PP/NR blends (100/0, 90/10, 80/20, 70/30, 60/40 and 50/50) were prepared and assessed for flexural strength using a three-point bending test. After this test, the PP/NR blends with 100/0, 90/10 and 80/20 ratios were selected and underwent autoclave sterilization for 1, 5 and 10 cycles. Eventually, the flexural strength testing was repeated and investigated. An analysis of variance and Tukey’s test were used to evaluate the flexural strength of various PP/NR blends before autoclave sterilization at p < 0.05. An analysis of variance and Dunnett’s T3 test were used to evaluate the flexural strength of selected PP/NR blends before and after autoclave sterilization at p < 0.05. Results: The results revealed that the flexural strength of PP/NR blended materials showed a statistically significant difference in every group of this study. The autoclave sterilization test revealed that the flexural strength of the PP/NR 90/10 and 80/20 ratios was significantly increased after sterilization for 1, 5 and 10 cycles. In addition, the PP/NR 90/10 ratio was also comparable to the 100/0 ratio. The lower NR content in PP/NR blends resulted in significantly higher flexural strength, and autoclave sterilization had an effect on this property. Conclusions: This study suggested that the PP/NR blend with a 90/10 ratio might be considered as an alternative material for developing rubber dam clamps.
- Open Access
Optimizing Processing Parameters for NR/EBC Thermoplastic Vulcanizates: A Comprehensive Full Factorial Design of Experiments (DOE) Strategy
This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene–butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance their mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and, thus, the success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tan δ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.
Open AccessOptimizing Processing Parameters for NR/EBC Thermoplastic Vulcanizates: A Comprehensive Full Factorial Design of Experiments (DOE) Strategy
This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene–butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance their mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and, thus, the success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tan δ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.
- Open Access
- 12 June 2024
- Published by MDPI AG in Preprints.org
Optimizing Processing Parameters for NR/EBC Thermoplastic Vulcanizates: A Comprehensive Full Factorial Design of Experiments (DOE) Strategy
This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene-butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance the mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and thus a success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tanδ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.
- 12 June 2024
- Published by MDPI AG in Preprints.org
Open AccessOptimizing Processing Parameters for NR/EBC Thermoplastic Vulcanizates: A Comprehensive Full Factorial Design of Experiments (DOE) Strategy
This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene-butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance the mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and thus a success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tanδ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.
- Open Access
- 20 March 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 2155-2168
Improvement of mechanical and dynamic properties of high silica filled epoxide functionalized natural rubber
- 20 March 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 2155-2168
Open AccessImprovement of mechanical and dynamic properties of high silica filled epoxide functionalized natural rubber
- Open Access
One-Pot Reactive Melt Recycling of PLA Post-Consumer Waste for the Production of Block Copolymer Nanocomposites of High Strength and Ductility
Post-consumer waste recycling is a crucial issue for building a sustainable society. However, mechanical recycling of poly(lactic acid) (PLA) often reduces the performance of the recycled material because PLA has a strong tendency to degrade during reprocessing. Therefore, it is of great interest to develop an effective recycling method to improve the mechanical performance of this material. This paper presents a one-pot melt process for turning PLA waste into a biodegradable block copolymer and its high strength and ductility composite. The process was conducted in a melt-mixer through a transesterification of PLA with poly(ethylene glycol) (PEG) or poly(propylene glycol) (PPG) as a soft component and clay as reinforcement. Effects of soft component content and sequence of clay addition on the mechanical performance of the prepared materials were focused. The results showed the successful preparation of PLA-based multiblock copolymers of high molecular weights (~100 kDa). Both virgin PLA and recycled source could serve as the starting material. PEG was more efficient than PPG in providing an intense improvement of PLA ductility. The nanocomposite of intercalated structure yielded nearly 100 times higher elongation at break (Eb = 506%) than the starting PLA (Eb = 5.6%) with high strength of 39.5 MPa and modulus of 1.4 GPa, considering the advantages of clay addition. Furthermore, the products with a broadened range of properties can be designed based on the ratio of PLA and soft component, as well as the organization and spatial distribution of clay in the copolymer matrices.
Open AccessOne-Pot Reactive Melt Recycling of PLA Post-Consumer Waste for the Production of Block Copolymer Nanocomposites of High Strength and Ductility
Post-consumer waste recycling is a crucial issue for building a sustainable society. However, mechanical recycling of poly(lactic acid) (PLA) often reduces the performance of the recycled material because PLA has a strong tendency to degrade during reprocessing. Therefore, it is of great interest to develop an effective recycling method to improve the mechanical performance of this material. This paper presents a one-pot melt process for turning PLA waste into a biodegradable block copolymer and its high strength and ductility composite. The process was conducted in a melt-mixer through a transesterification of PLA with poly(ethylene glycol) (PEG) or poly(propylene glycol) (PPG) as a soft component and clay as reinforcement. Effects of soft component content and sequence of clay addition on the mechanical performance of the prepared materials were focused. The results showed the successful preparation of PLA-based multiblock copolymers of high molecular weights (~100 kDa). Both virgin PLA and recycled source could serve as the starting material. PEG was more efficient than PPG in providing an intense improvement of PLA ductility. The nanocomposite of intercalated structure yielded nearly 100 times higher elongation at break (Eb = 506%) than the starting PLA (Eb = 5.6%) with high strength of 39.5 MPa and modulus of 1.4 GPa, considering the advantages of clay addition. Furthermore, the products with a broadened range of properties can be designed based on the ratio of PLA and soft component, as well as the organization and spatial distribution of clay in the copolymer matrices.
- 26 May 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (29)
Optimization of highly dispersible silica/carbon black hybrid filler ratio for tire tread based on solution‐ andemulsion‐styrenebutadiene rubber
In this study, the effects of hybrid filler ratio and styrene‐butadiene rubber (SBR) type on tire tread performance that is, wet grip (WG), fuel‐saving efficiency (FSE), and abrasion resistance, were focused. Two types of SBR that is solution‐SBR (S‐SBR) and emulsion‐SBR (E‐SBR) were selected and reinforced by various ratios of highly dispersible silica (HDSi) to carbon black (CB). Although increasing the CB ratio had negative effects on WG, FSE, heat build‐up, and dynamic set, it improved abrasion resistance. Results revealed a good balance of tire performance at a CB ratio of 40 wt%. Clearly, S‐SBR provided better overall tire performance than E‐SBR, particularly in the silica‐filled system. This is possibly due to the higher glass transition temperature (Tg) and the greater magnitudes of rubber‐filler interaction and crosslink density of S‐SBR. Surprisingly, the HDSi/CB hybrid ratio and the SBR type had little influence on the degree of filler dispersion, probably because of the sufficiently long mixing time employed in this experiment.
- 26 May 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (29)
Optimization of highly dispersible silica/carbon black hybrid filler ratio for tire tread based on solution‐ andemulsion‐styrenebutadiene rubber
In this study, the effects of hybrid filler ratio and styrene‐butadiene rubber (SBR) type on tire tread performance that is, wet grip (WG), fuel‐saving efficiency (FSE), and abrasion resistance, were focused. Two types of SBR that is solution‐SBR (S‐SBR) and emulsion‐SBR (E‐SBR) were selected and reinforced by various ratios of highly dispersible silica (HDSi) to carbon black (CB). Although increasing the CB ratio had negative effects on WG, FSE, heat build‐up, and dynamic set, it improved abrasion resistance. Results revealed a good balance of tire performance at a CB ratio of 40 wt%. Clearly, S‐SBR provided better overall tire performance than E‐SBR, particularly in the silica‐filled system. This is possibly due to the higher glass transition temperature (Tg) and the greater magnitudes of rubber‐filler interaction and crosslink density of S‐SBR. Surprisingly, the HDSi/CB hybrid ratio and the SBR type had little influence on the degree of filler dispersion, probably because of the sufficiently long mixing time employed in this experiment.