JSJosef Schätz

Josef Schätz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Josef Schätz has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Pulsed DC Sputter Deposition of Stable Turbostratic Boron Nitride Thin Films

    by Josef Schätz, Michael Krenzer, Tim Schaffus, Martin Otto, Fabian Kühnel, Fabian Streb, Günther Benstetter, Georg S. Duesberg, Stephan Pindl, Max C. Lemme

    Boron nitride (BN) is considered for several applications in microelectronics, such as thermal management, optoelectronics, or as memristors. BN can be deposited with different deposition methods, but any integration in the back‐end‐of‐the‐line limits the deposition temperature to approximately 400°C. Further requirements include high crystal quality, sufficient film stability, and a high deposition rate to limit process costs. In particular, investigations into thin film stability and high deposition rates have rarely been conducted. Here, we propose reactive pulsed direct current sputtering at 250°C from a pure boron target and demonstrate the deposition process for stable nanocrystalline turbostratic BN. A substrate bias voltage between the plasma and sample reduces excess boron in the film and enhances its crystallinity. The process effectively prevents the formation of boric acid and ammonium borate hydrate. The stable BN films have a crystallite size of approximately 5 nm and an out‐of‐plane texture. Leakage current investigations demonstrate the insulating properties of the films. A high deposition rate of 81.6 nm min – 1 and the use of state‐of‐the‐art sputter hardware allow the immediate integration of sputtered BN into semiconductor device process lines.


  • Open Access

    Measuring the Adhesion of Graphene Flake Networks via Button Shear Tests

    by Jorge Eduardo Adatti Estévez, Josef Schätz, Jasper Ruhkopf, Aleksandr Baklanov, Annika Weber, David Tumpold, Alexander Zöpfl, Ulrich Krumbein, Max Christian Lemme

    Graphene flake-based dispersions are attractive materials for various applications in microelectronics because of their ease of fabrication and the potential to deposit them on diverse substrates. The integration of these materials into conductive networks and microdevices requires thorough knowledge of their mechanical material properties, including adhesion. This paper presents quantitative adhesion measurements of graphene flake networks on silicon dioxide (SiO2) via button shear testing (BST). In this method, shear forces are applied to prefabricated micrometric buttons until they delaminate, providing information about the shear strength of the underlying graphene. We applied BST to graphene flake networks with different flake structures and defect densities. Flat flakes, a flat network structure, and a high flake defect density improve adhesion. We further demonstrate that graphene flake networks have stronger adhesion than chemical vapor-deposited (CVD) monolayer graphene grown on copper and transferred to SiO2. Hexamethyldisilazane (HMDS) increases the total adhesion force by improving flake network formation. Finally, we provide flake-type-specific delamination patterns by combining BST, optical microscopy, and Raman spectroscopy. We establish BST as a quantitative technique for measuring the adhesion of graphene dispersions and show the crucial role of interflake junctions in the overall adhesion of graphene flake networks.


  • Open Access

    Button shear testing for adhesion measurements of 2D materials

    by Josef Schätz, Navin Nayi, Jonas Weber, Christoph Metzke, Sebastian Lukas, Jürgen Walter, Tim Schaffus, Fabian Streb, Eros Reato, Agata Piacentini, et al.

    Two-dimensional (2D) materials are considered for numerous applications in microelectronics, although several challenges remain when integrating them into functional devices. Weak adhesion is one of them, caused by their chemical inertness. Quantifying the adhesion of 2D materials on three-dimensional surfaces is, therefore, an essential step toward reliable 2D device integration. To this end, button shear testing is proposed and demonstrated as a method for evaluating the adhesion of 2D materials with the examples of graphene, hexagonal boron nitride (hBN), molybdenum disulfide, and tungsten diselenide on silicon dioxide and silicon nitride substrates. We propose a fabrication process flow for polymer buttons on the 2D materials and establish suitable button dimensions and testing shear speeds. We show with our quantitative data that low substrate roughness and oxygen plasma treatments on the substrates before 2D material transfer result in higher shear strengths. Thermal annealing increases the adhesion of hBN on silicon dioxide and correlates with the thermal interface resistance between these materials. This establishes button shear testing as a reliable and repeatable method for quantifying the adhesion of 2D materials.


  • Current-Limited Conductive Atomic Force Microscopy

    by Jonas Weber, Yue Yuan, Sebastian Pazos, Fabian Kühnel, Christoph Metzke, Josef Schätz, Werner Frammelsberger, Günther Benstetter, Mario Lanza

    Conductive atomic force microscopy (CAFM) has become the preferred tool of many companies and academics to analyze the electronic properties of materials and devices at the nanoscale. This technique scans the surface of a sample using an ultrasharp conductive nanoprobe so that the contact area between them is very small (<100 nm(2)) and it can measure the properties of the sample with a very high lateral resolution. However, measuring relatively low currents (similar to 1 nA) in such small areas produces high current densities (similar to 1000 A/cm(2)), which almost always results in fast nanoprobe degradation. That is not only expensive but also endangers the reliability of the data collected because detecting which data sets are affected by tip degradation can be complex. Here, we show an inexpensive long-sought solution for this problem by using a current limitation system. We test its performance by measuring the tunneling current across a reference ultrathin dielectric when applying ramped voltage stresses at hundreds of randomly selected locations of its surface, and we conclude that the use of a current limitation system increases the lifetime of the tips by a factor of similar to 50. Our work contributes to significantly enhance the reliability of one of the most important characterization techniques in the field of nanoelectronics.


  • Open Access

    Solid Platinum Nanoprobes for Highly Reliable Conductive Atomic Force Microscopy

    by Jonas Weber, Yue Yuan, Fabian Kühnel, Christoph Metzke, Josef Schätz, Werner Frammelsberger, Günther Benstetter, Mario Lanza

    Conductive atomic force microscopy (CAFM) is a powerful technique to investigate electrical and mechanical properties of materials and devices at the nanoscale. However, its main challenge is the reliability of the probe tips and their interaction with the samples. The most common probe tips used in CAFM studies are made of Si coated with a thin (∼20 nm) film of Pt or Pt-rich alloys (such as Pt/Ir), but this can degrade fast due to high current densities (>102A/cm2) and mechanical frictions. Si tips coated with doped diamond and solid doped diamond tips are more durable, but they are significantly more expensive and their high stiffness often damages the surface of most samples. One growing alternative is to use solid Pt tips, which have an intermediate price and are expected to be more durable than metal-coated silicon tips. However, a thorough characterization of the performance of solid Pt probes for CAFM research has never been reported. In this article, we characterize the performance of solid Pt probes for nanoelectronics research by performing various types of experiments and compare them to Pt/Ir-coated Si probes. Our results indicate that solid Pt probes exhibit a lateral resolution that is very similar to that of Pt/Ir-coated Si probes but with the big advantage of a much longer lifetime. Moreover, the probe-to-probe deviation of the electrical data collected is small. The use of solid Pt probes can help researchers to enhance the reliability of their CAFM experiments.


  • Open Access

    Investigation of Heater Structures for Thermal Conductivity Measurements of SiO2 and Al2O3 Thin Films Using the 3-Omega Method

    by Fabian Kühnel, Christoph Metzke, Jonas Weber, Josef Schätz, Georg S. Duesberg, Günther Benstetter

    A well-known method for measuring thermal conductivity is the 3-Omega (3ω) method. A prerequisite for it is the deposition of a metal heater on top of the sample surface. The known design rules for the heater geometry, however, are not yet sufficient. In this work, heaters with different lengths and widths within the known restrictions were investigated. The measurements were carried out on SiO2 thin films with different film thicknesses as a reference. There was a significant difference between theoretical deposited heater width and real heater width, which could lead to errors of up to 50% for the determined thermal conductivity. Heaters with lengths between 11 and 13 mm and widths of 6.5 µm or more proved to deliver the most trustworthy results. To verify the performance of these newfound heaters, additional investigations on Al2O3 thin films were carried out, proving our conclusions to be correct and delivering thermal conductivity values of 0.81 Wm−1 K−1 and 0.93 Wm−1 K−1 for unannealed and annealed samples, respectively. Furthermore, the effect of annealing on Al2O3 was studied, revealing a significant shrinking in film thickness of approximately 11% and an increase in thermal conductivity of 15%. The presented results on well-defined geometries will help to produce optimized heater structures for the 3ω method.