Veer Vatsa
Veer Vatsa has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- John Kent Lin
University of Texas MD Anderson Cancer Center, Houston, TX
2 shared publications - Vandana Nanal
Tata Institute of Fundamental Research
2 shared publications A. Mazumdar
Indian Inst Technol Ropar, TIF AWaDH, Rupnagar 140001, Punjab, India
1 shared publication- A. Mazumdar
Department of Physics and Astronomy, University of North Carolina, Chapel Hill, North Carolina 27599, USA
1 shared publication - A. Shrivastava
Homi Bhabha National Institute
1 shared publication - Anand Upadhyay
Department of IT, Thakur College of Science and Commerce, Mumbai, India
1 shared publication
Latest Publications
- Open Access
- 1 July 2021
- Published by Elsevier in Scripta Materialia
- Vol. 199, 113858
Synchrotron x-ray diffraction studies of the α ⇌ β structural phase transition in Sn and Sn-Cu
- 1 July 2021
- Published by Elsevier in Scripta Materialia
- Vol. 199, 113858
Open AccessSynchrotron x-ray diffraction studies of the α ⇌ β structural phase transition in Sn and Sn-Cu
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
CFD and Experimental Data Comparisons for Conventional and AFC-Enabled CRM High-Lift Configurations (Invited)
Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of a representative conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface of the flap shoulder, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to produce the aerodynamic performance (lift) comparable to that of the CRM-HL configuration over a large angle of attack range encompassing maximum lift conditions. For comparison purposes, computations are also performed for the CRM-HL configuration. In the current paper, PowerFLOW, a CFD code based on the Lattice Boltzmann method (LBM), is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOW code that has been validated for high-speed flows is used to simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. This study is focused on the AFC systems and actuator arrangements that had emerged based on the parametric studies conducted previously at the nominal landing condition. Comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations over a broad angle of attack range. The numerical solutions predict the expected trends in aerodynamic forces with angle of attack variation.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
CFD and Experimental Data Comparisons for Conventional and AFC-Enabled CRM High-Lift Configurations (Invited)
Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of a representative conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface of the flap shoulder, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to produce the aerodynamic performance (lift) comparable to that of the CRM-HL configuration over a large angle of attack range encompassing maximum lift conditions. For comparison purposes, computations are also performed for the CRM-HL configuration. In the current paper, PowerFLOW, a CFD code based on the Lattice Boltzmann method (LBM), is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOW code that has been validated for high-speed flows is used to simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. This study is focused on the AFC systems and actuator arrangements that had emerged based on the parametric studies conducted previously at the nominal landing condition. Comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations over a broad angle of attack range. The numerical solutions predict the expected trends in aerodynamic forces with angle of attack variation.
- Open Access
- 13 June 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Numerical Simulation of a High-Lift Configuration with Embedded Fluidic Actuators
- 13 June 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Open AccessNumerical Simulation of a High-Lift Configuration with Embedded Fluidic Actuators
- Open Access
- 10 May 2004
- Published by American Institute of Aeronautics and Astronautics (AIAA)
A Model for Shear Layer Effects on Engine Noise Radiation
- 10 May 2004
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Open AccessA Model for Shear Layer Effects on Engine Noise Radiation
- 1 January 1991
- Published by Elsevier in Computers & Fluids
- Vol. 20 (3) , 313-320
Viscous flow solutions for slender bodies of revolution at incidence
- 1 January 1991
- Published by Elsevier in Computers & Fluids
- Vol. 20 (3) , 313-320
Viscous flow solutions for slender bodies of revolution at incidence