SLShigang Lu

Shigang Lu

*This is an algorithmically generated author record based on publicly available information.

Shigang Lu has a total of 85 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Interface stabilization of 1,1,2,2‐tetrafluoroethyl‐2,2,3,3‐tetrafluoropropyl ether to high‐voltage Li‐rich Mn‐based layered cathode materials

    by A‐Lin Li, Guo‐Hua Li, Shi‐Gang Lu, Zhi‐Min Ren, Jian‐Tao Wang, Hao‐Xiang Zhuo, Wei Quan, Gang‐Ning Zhang, Fu‐Juan Han, Yi‐Mian Xia, et al.

    Non‐aqueous electrolyte solvents play a pivotal role in improving the cycling performance of high‐voltage Li‐rich Mn‐based layered cathode materials. In this study, a fluoroether (1,1,2,2‐tetrafluoroethyl‐2,2,3,3‐tetrafluoropropyl ether, TFEPE) was added to 1.2 mol·L −1 LiPF 6 EC/EMC/DEC at different concentrations to synthesize a series of electrolytes for enhancing the cycling performance of high‐voltage Li 1.18 Mn 0.50 Ni 0.26 Co 0.06 O 2 (LMNC). Effects of TFEPE on the electrochemical performance of LMNC at 0.1C and 1.0C rates were investigated. Scanning electron microscopy was used to observe the surface morphology of LMNC before and after cycling. X‐ray photoelectron spectroscopy was conducted to analyze the surface compositions and chemical states, and transmission electron microscopy was performed to directly examine the changes in the structure of LMNC before and after cycling. Results suggested that TFEPE was preferentially oxidized and produced inorganic compounds (MeF and Li 2 CO 3 ) on the surface of LMNC, which effectively inhibited the side reactions between LMNC and the electrolyte. MeF and Li 2 CO 3 delayed the propagation of the phase transitions of LMNC primary particles from the surface to the bulk, thereby improving the cycling performance of LMNC.


  • Lithium‐ion cell inconsistency analysis based on three‐parameter Weibull probability model

    by Lin‐Shu Wang, Yan‐Yan Fang, Ting Zhao, Jian‐Tao Wang, Hang Zhang, Lin Wang, Shi‐Gang Lu

    The inconsistency of lithium‐ion cells degrades battery performance, lifetime and even safety. The complexity of the cell reaction mechanism causes an irregular asymmetrical distribution of various cell parameters, such as capacity and internal resistance, among others. In this study, the Newman electrochemical model was used to simulate the 1C discharge curves of 100 LiMn 2 O 4 pouch cells with parameter variations typically produced in manufacturing processes, and the three‐parameter Weibull probability model was used to analyze the dispersion and symmetry of the resulting discharge voltage distributions. The results showed that the dispersion of the voltage distribution was related to the rate of decrease in the discharge voltage, and the symmetry was related to the change in the rate of voltage decrease. The effect of the cells’ capacity dominated the voltage distribution thermodynamically during discharge, and the phase transformation process significantly skewed the voltage distribution. The effects of the ohmic drop and polarization voltage on the voltage distribution were primarily kinetic. The presence of current returned the right‐skewed voltage distribution caused by phase transformation to a more symmetrical distribution. Thus, the Weibull parameters elucidated the electrochemical behavior during the discharge process, and this method can guide the prediction and control of cell inconsistency, as well as detection and control strategies for cell management systems.


  • Open Access

    Principle understanding towards synthesizing Fe/N decorated carbon catalysts with pyridinic-N enriched and agglomeration-free features for lithium–oxygen batteries

    by Gangning Zhang, Li Zhang, Shangqian Zhao, Shigang Lu, Yan Lu, Haobo Sun, Lve Wang

    Metal-N-decorated carbon catalysts are cheap and effective alternatives for replacing the high-priced Pt-based ones in activating the reduction of oxygen for metal–air or fuel cells. The preparation of such heterogeneous catalysts often requires complex synthesis processes, including harsh acid treatment, secondary pyrolysis processes, etching, etc., to make the heteroatoms evenly dispersed in the carbon substrates to obtain enhanced activities. Through combined experimental characterizations, we found that by precise control of the precursors added, a Fe/N uniformly distributed, agglomeration-free Fe/N decorated Super-P carbon material (FNDSP) can be easily obtained by a one-pot synthesis process with distinctly higher pyridinic-N content and elevated catalytic activity. An insight into this phenomenon was carefully demonstrated and also verified in Li–O2 batteries, which delivered a high discharging platform of 2.85 V and can be fully discharged with a capacity of 5811.5 mA h gcarbon+catalyst −1 at the cut-off voltage of 2.5 V by the low-cost Super-P modified catalyst.


  • Li3PO4 modification on a primary particle surface for high performance Li-rich layered oxide Li1.18Mn0.52Co0.15Ni0.15O2via a synchronous route

    by Xianghuan Liu, Zhenyao Wang, Weidong Zhuang, Liqing Ban, Min Gao, Wenjin Li, Yanping Yin, Zhong Wang, Shigang Lu

    A Li-rich layered oxide, Li1.18Mn0.52Co0.15Ni0.15O2, with Li3PO4 modification on the surface of a primary particle, was synthesized by a facile synchronous method.


  • Effect of Dual‐Salt Concentrated Electrolytes on the Electrochemical Performance of Silicon Nanoparticles

    by Zeng‐Hua Chang, Xiang Li, Feng‐Ling Yun, Ze‐Chao Shao, Zhao‐Hui Wu, Jian‐Tao Wang, Shi‐Gang Lu

    As a promising anode material, silicon has attracted extensive attention. The instability of the electrode/electrolyte interphase due to the inherent volume variation upon (de)lithiation is one of the major factors limiting the commercialization of silicon anode materials. Here, we report a concentrated electrolyte with lithium bis(fluorosulfonyl)imide (LiFSI) and lithium difluoro (oxalate) borate (LiDFOB) dual salt to enhance the control of the species constituting the solid electrolyte interphase (SEI) on the surface of the silicon material. The silicon nanoparticle (SiNP) electrode with the dual‐salt LiFSI0.7LiDFOB0.3‐(PC)4 concentrated electrolyte delivers a relatively high average coulombic efficiency of 97.68 % and a remarkably improved cycling performance with an initial capacity of approximately 3300 mAh g−1 and a capacity retention around 2000 mAh g−1 after 100 cycles. It is found that the polarity of the B−F bond of LiDFOB decreases when the molar ratio of LiDFOB to LiFSI is greater than 0.3 : 0.7. Therefore, the reduction of LiDFOB through a ring‐opening reaction coupled with a ring‐opening reaction of PC becomes dominant. The SEI layer rich in the corresponding products Li(BF2O)n polymer could suppress the rupture of the Si particles and excessive growth of the SEI layer, thus could further mitigate the decrease of coulombic efficiency.


  • Tuning surface conductivity and stability for high-performance Li- and Mn-rich cathode materials

    by Zhao Li, Qiang Li, Anbang Zhang, Wen Wen, Lin Wang, Zhenyao Wang, Jiantao Wang, Shigang Lu, Xiaolong Li, Zhong Wang

    Li- and Mn-rich (LMR) layered materials with large specific capacities are one of the most promising cathodes for high-energy Li-ion batteries. However, the oxygen redox reaction induced by the activation of the Li2MnO3 component leads to lattice oxygen release and transition metal migration from the surface, which result in a large irreversible capacity loss, poor rate capability and inferior cycle stability compared with other cathodes. In this study, an integrated surface modification of combining a coating and chemical treatment is proposed to achieve modified LMR cathode materials with graphene wrapping layers and surface spinel phases. The graphene layer promotes electron transfer, and the spinel phase interlayer accelerates Li+ diffusion. Simultaneously, the combination of the two components increases the structural stability of LMR materials. As a result, the surface-modified LMR cathode exhibits a high rate capability of 154.3 mA h g−1 at 5C and an excellent cycle stability with a capacity retention of 84.2% after 200 cycles at 1C. In addition, the structural evolution of the surface-modified LMR cathode material was studied by in situ synchrotron X-ray diffraction analysis during the charge–discharge process, which illustrates that the surface modification has a significant effect on mitigating oxygen release by enhancing the surface structural stability.


  • Electrochemical properties of high‐loading sulfur–carbon materials prepared by in situ generation method

    by Can Jiao, Chun‐Rong Zhao, Li Zhang, Shang‐Qian Zhao, Guo‐Yao Pang, Hao‐Bo Sun, Shi‐Gang Lu

    A high sulfur content sulfur–carbon composite was synthesized via in situ generation method in aqueous solution. When the sulfur loading is up to 90%, the electrode still exhibits good cycling performance with a reversible capacity of about 623 mAh·g −1 after 100 cycles. To further commercialize the Li–S battery, understanding the capacity degradation mechanism is very essential, especially with a high sulfur loading electrode. To achieve this goal, the electrochemical performance of the high sulfur loading electrode was studied, and the structure change of the electrode after cycling was also examined by ex situ scanning electron microscopy (SEM) and other techniques. The result shows that the Li 2 S 2 and Li 2 S inhomogeneous precipitation contributes to the majority capacity fading of the high sulfur loading Li–S cells.


  • A high‐performance lithium anode based on N‐doped composite graphene

    by Can Jiao, Hao‐Bo Sun, Li Zhang, Shang‐Qian Zhao, Guo‐Yao Pang, Chun‐Rong Zhao, Shi‐Gang Lu

    Lithium (Li) metal is the most promising electrode for next‐generation rechargeable batteries. In order to push the commercialization of the lithium metal batteries, a kind of nitrogen(N)‐doped composite graphene (NCG) adopted as the Li plating host was prepared to regulate Li metal nucleation and suppress dendrite growth. Furthermore, a new kind of sandwich‐type composite lithium metal (STCL) electrode was developed to improve its application. The STCL electrode can be used as convenient as a piece of Li foil but no dendrite growth. In a symmetric battery, the STCL electrode cycled for more than 4500 h with the overpotential of less than 40 mV. And due to the creative design, the STCL promises the Li–S battery with a prolonged cycling lifespan.