Yuewen Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yuewen Huang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Bo Feng
Huazhong University of Science and Technology
2 shared publications - Jikai Zhang
National Center for Dam Safety Engineering Technology Research, Changjiang River Scientific Research Institute, Wuhan, China
2 shared publications - Yihua Kang
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
2 shared publications - Cheng Liang
Institute of Science and Technology, China Three Gorges Corporation
1 shared publication - Fangfang Zhou
National Center for Dam Safety Engineering Technology Research, Changjiang River Scientific Research Institute, Wuhan 430010, China
1 shared publication - Jian Tang
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
1 shared publication
Latest Publications
- Open Access
Inspection of Cracks in the Piston Rod of a Hydraulic Cylinder Using Injected Alternating Current-Field Measurement
This paper proposes a method of injected alternating current-field measurement (IAC-FM) for detecting orthogonal cracks in the piston rod of a hydraulic cylinder in a gate hoist. Using this method, both longitudinal and transverse cracks can be detected at the same time. An alternating magnetic field is produced inside the steel rod by axially injecting an alternating current into the rod. The longitudinal crack perturbs the circumferential magnetic field, whereas the transverse crack perturbs the current in the axial direction. Analyses of the behaviors of the magnetic field in the vicinity of the cracks were proposed, using a three-dimensional finite element software. An experimental setup was built and validation experiments were performed. The effects of the operating frequency and scan path were also studied. The results verified the feasibility of the IAC-FM method and showed great potential for the inspection of in-service hydraulic cylinders of gate hoists.
Open AccessInspection of Cracks in the Piston Rod of a Hydraulic Cylinder Using Injected Alternating Current-Field Measurement
This paper proposes a method of injected alternating current-field measurement (IAC-FM) for detecting orthogonal cracks in the piston rod of a hydraulic cylinder in a gate hoist. Using this method, both longitudinal and transverse cracks can be detected at the same time. An alternating magnetic field is produced inside the steel rod by axially injecting an alternating current into the rod. The longitudinal crack perturbs the circumferential magnetic field, whereas the transverse crack perturbs the current in the axial direction. Analyses of the behaviors of the magnetic field in the vicinity of the cracks were proposed, using a three-dimensional finite element software. An experimental setup was built and validation experiments were performed. The effects of the operating frequency and scan path were also studied. The results verified the feasibility of the IAC-FM method and showed great potential for the inspection of in-service hydraulic cylinders of gate hoists.
- Open Access
A Displacement Sensing Method Based on Permanent Magnet and Magnetic Flux Measurement
This paper proposes a displacement sensing method based on magnetic flux measurement. A bridge-structured magnetic circuit, formed by permanent magnets and two ferromagnetic cores, is designed and discussed. The analyses of the equivalent magnetic circuit and three-dimensional finite element simulations showed that the magnetic flux density changes linearly with the reciprocal of the sum of a constant and the displacement. A prototype sensor of the bridge structure is developed that consists of four permanent magnets as excitation, a Hall sensor as reception, and two ferromagnetic cores as the connection. Experiments have validated the feasibility of this method. The measured results show a good linearity between the sensor’s output and the reciprocal of the sum of a constant and the displacement, with a correlation coefficient greater than 0.9995 across different measurement ranges. Additionally, the measured results significantly indicate that the proposed sensor is compatible with different ferromagnetic materials with a worst-case error of less than 5%. The proposed sensor has the advantages of low cost and good linearity; however, the test object is limited to ferromagnetic materials.
Open AccessA Displacement Sensing Method Based on Permanent Magnet and Magnetic Flux Measurement
This paper proposes a displacement sensing method based on magnetic flux measurement. A bridge-structured magnetic circuit, formed by permanent magnets and two ferromagnetic cores, is designed and discussed. The analyses of the equivalent magnetic circuit and three-dimensional finite element simulations showed that the magnetic flux density changes linearly with the reciprocal of the sum of a constant and the displacement. A prototype sensor of the bridge structure is developed that consists of four permanent magnets as excitation, a Hall sensor as reception, and two ferromagnetic cores as the connection. Experiments have validated the feasibility of this method. The measured results show a good linearity between the sensor’s output and the reciprocal of the sum of a constant and the displacement, with a correlation coefficient greater than 0.9995 across different measurement ranges. Additionally, the measured results significantly indicate that the proposed sensor is compatible with different ferromagnetic materials with a worst-case error of less than 5%. The proposed sensor has the advantages of low cost and good linearity; however, the test object is limited to ferromagnetic materials.