Nikolay Bukharin
Research Subjects
Nikolay Bukharin has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Aleksey I. Ukolov
Kerch State Maritime Technological University
1 shared publication - Anatoliy A. Monakhov
Institute of Mechanics, Moscow State University, Moscow, Russia
1 shared publication - Irina Pakhlyan
Armavir Institute of Mechanics and Technology, Kuban State Technological University, Armavir 352905, Russia
1 shared publication - Maxim Omelyanyuk
Armavir Institute of Mechanics and Technology, Kuban State Technological University, Armavir 352905, Russia
1 shared publication - Mouhammad El Hassan
Mechanical Engineering Department, Prince Mohammad Bin Fahd University, Al Khobar 34754, Saudi Arabia
1 shared publication
Latest Publications
- Open Access
- 29 November 2023
- Published by Tsinghua University Press in Friction
- Vol. 12 (2) , 356-362
Saffman–Taylor instability in eccentric cylinders at gaseous cavitation
A flow of silicon fluid in the gap between eccentric cylinders was studied experimentally. The condition of gaseous cavitation inception during the rotation of internal cylinder was considered. It was shown that at reduction of the gap between cylinders Saffman–Taylor instability appeared on surface of the internal cylinder and then gaseous cavitation was observed. Possibility of one uniform gas formation appearance under this type of instability was demonstrated.
- 29 November 2023
- Published by Tsinghua University Press in Friction
- Vol. 12 (2) , 356-362
Open AccessSaffman–Taylor instability in eccentric cylinders at gaseous cavitation
A flow of silicon fluid in the gap between eccentric cylinders was studied experimentally. The condition of gaseous cavitation inception during the rotation of internal cylinder was considered. It was shown that at reduction of the gap between cylinders Saffman–Taylor instability appeared on surface of the internal cylinder and then gaseous cavitation was observed. Possibility of one uniform gas formation appearance under this type of instability was demonstrated.
- Open Access
Experimental and Numerical Study of Cavitation Number Limitations for Hydrodynamic Cavitation Inception Prediction
Hydrodynamic cavitation is the formation, growth and subsequent collapse of vapor bubbles in a moving liquid. It is extremely important to determine conditions of cavitation inception and when it starts damaging industrial equipment. In some cases, such as hydrodynamic cleaning it is important to understand how to improve the cavitation phenomenon in order to enhance cleaning properties. The cavitation number is a parameter used to predict cavitation and its potential effects. In this paper we discuss limitations of this parameter and demonstrate that it cannot be considered sufficient to predict cavitation inception and development in the fluid flow. The experimental setup was designed and built to study cavitation inception in various nozzles. RANS SST k–ω turbulence model was used in this study to model turbulent flow in ANSYS Fluent. CFD calculations were compared to experimental results. It was shown that cavitation inception was sensitive to change in nozzle geometry and, since geometrical parameters are not included in cavitation number formula, scenarios of cavitation inception can be different at the same cavitation number.
Open AccessExperimental and Numerical Study of Cavitation Number Limitations for Hydrodynamic Cavitation Inception Prediction
Hydrodynamic cavitation is the formation, growth and subsequent collapse of vapor bubbles in a moving liquid. It is extremely important to determine conditions of cavitation inception and when it starts damaging industrial equipment. In some cases, such as hydrodynamic cleaning it is important to understand how to improve the cavitation phenomenon in order to enhance cleaning properties. The cavitation number is a parameter used to predict cavitation and its potential effects. In this paper we discuss limitations of this parameter and demonstrate that it cannot be considered sufficient to predict cavitation inception and development in the fluid flow. The experimental setup was designed and built to study cavitation inception in various nozzles. RANS SST k–ω turbulence model was used in this study to model turbulent flow in ANSYS Fluent. CFD calculations were compared to experimental results. It was shown that cavitation inception was sensitive to change in nozzle geometry and, since geometrical parameters are not included in cavitation number formula, scenarios of cavitation inception can be different at the same cavitation number.