Jiaming Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiaming Liu has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Ming Liu
Xi’an Jiaotong University
6 shared publications - Zhongqiang Hu
Xi’an Jiaotong University
6 shared publications - Mengmeng Guan
State Key Laboratory for Manufacturing Systems Engineering, Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education, Engineering Research Center of Spin Quantum Sensor Chips, School of Electronic Science and Engineering, Xian Jiaotong University, Xian, China
5 shared publications - Wei Su
State Key Laboratory for Manufacturing Systems Engineering, Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education, Engineering Research Center of Spin Quantum Sensor Chips, Universities of Shaanxi Province, School of Electronic Science and Engineering, Xian Jiaotong University, Xian, China
5 shared publications - Zhiguang Wang
State Key Laboratory for Manufacturing Systems Engineering, Electronic Materials Research Laboratory, School of Electronic Science and Engineering, Xian Jiaotong University, Xian, China
4 shared publications - Zhuangde Jiang
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049, China
3 shared publications
Latest Publications
- 2 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Reduced Harmonic Errors by Geometrically Modulating the Demagnetizing Fields in Wave-Type Anisotropic Magnetoresistance Angle Sensors
Anisotropic Magnetoresistance (AMR) angle sensors are widely utilized in industrial applications owing to their non-contact operation, cost efficiency, and miniaturization potential. However, harmonic distortion inherent in AMR measurements fundamentally limits angle encoder accuracy. This work introduces a high-precision AMR sensor employing a wave-type topology that suppresses harmonic errors through geometric innovation, demonstrating significant performance enhancements versus conventional strip-type sensors: 64.3% reduction in maximum angular error (0.50° vs. 1.4°), 65.3% lower worst-case nonlinearity (0.2% vs. 0.576%), and minimal change in repeatability (0.14° vs. 0.137°). Systematic evaluation of dynamic responses under variable field angles through Stoner–Wohlfarth modeling and experimental validation exhibits excellent agreement, confirming curvature optimization effectively minimizes angular errors. Mechanistic analysis identifies demagnetizing fields and induced anisotropy as dominant error sources. Crucially, this architecture maintains fabrication simplicity, demonstrating exceptional cost-performance synergy for automotive, robotics, and industrial automation applications requiring sub-0.5° accuracy.
- 2 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Reduced Harmonic Errors by Geometrically Modulating the Demagnetizing Fields in Wave-Type Anisotropic Magnetoresistance Angle Sensors
Anisotropic Magnetoresistance (AMR) angle sensors are widely utilized in industrial applications owing to their non-contact operation, cost efficiency, and miniaturization potential. However, harmonic distortion inherent in AMR measurements fundamentally limits angle encoder accuracy. This work introduces a high-precision AMR sensor employing a wave-type topology that suppresses harmonic errors through geometric innovation, demonstrating significant performance enhancements versus conventional strip-type sensors: 64.3% reduction in maximum angular error (0.50° vs. 1.4°), 65.3% lower worst-case nonlinearity (0.2% vs. 0.576%), and minimal change in repeatability (0.14° vs. 0.137°). Systematic evaluation of dynamic responses under variable field angles through Stoner–Wohlfarth modeling and experimental validation exhibits excellent agreement, confirming curvature optimization effectively minimizes angular errors. Mechanistic analysis identifies demagnetizing fields and induced anisotropy as dominant error sources. Crucially, this architecture maintains fabrication simplicity, demonstrating exceptional cost-performance synergy for automotive, robotics, and industrial automation applications requiring sub-0.5° accuracy.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 5567-5575
Suppression of Temperature Drift in Tunneling Magnetoresistance Current Sensors by Digital-Analog Hybrid Compensation
Tunneling magnetoresistance (TMR) current sensors have been studied extensively in recent years due to their advantages of high sensitivity and low power consumption. However, temperature drift remains a critical factor limiting their detection accuracy and stability. Here, we propose a digital-analog hybrid compensation scheme for temperature drift suppression and demonstrate a high-precision TMR current sensor prototype. Experimental verification shows that after compensation, the sensor achieves a sensitivity temperature drift of 17.18 ppm/°C and a zero-point temperature drift of 9.86 ppm/°C within the temperature range of −40°C to +80°C. Simultaneously, the TMR sensor features a working bandwidth of dc-80 kHz, with a full-scale error not exceeding 0.5%FS within the measurement range of ±10 Ap, a minimum resolution of 2 mA, and a dynamic range as high as 80 dB. The proposed digital-analog hybrid compensation method provides an important guidance for the design and application of TMR sensors with suppressed temperature drift.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 5567-5575
Suppression of Temperature Drift in Tunneling Magnetoresistance Current Sensors by Digital-Analog Hybrid Compensation
Tunneling magnetoresistance (TMR) current sensors have been studied extensively in recent years due to their advantages of high sensitivity and low power consumption. However, temperature drift remains a critical factor limiting their detection accuracy and stability. Here, we propose a digital-analog hybrid compensation scheme for temperature drift suppression and demonstrate a high-precision TMR current sensor prototype. Experimental verification shows that after compensation, the sensor achieves a sensitivity temperature drift of 17.18 ppm/°C and a zero-point temperature drift of 9.86 ppm/°C within the temperature range of −40°C to +80°C. Simultaneously, the TMR sensor features a working bandwidth of dc-80 kHz, with a full-scale error not exceeding 0.5%FS within the measurement range of ±10 Ap, a minimum resolution of 2 mA, and a dynamic range as high as 80 dB. The proposed digital-analog hybrid compensation method provides an important guidance for the design and application of TMR sensors with suppressed temperature drift.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 12626-12633
Wideband Tunneling Magnetoresistance Current Sensor With Dual-Parallel Current Trace Utilizing the Skin Effect
In highly integrated switching circuits and power electronic converters, noncontact wideband current sensors are typically required for monitoring operational status. However, the magnetic field distribution of printed circuit board traces is influenced by the skin effect as the current frequency increases, which, in turn, affects the frequency characteristics of the sensor. In this study, we propose a dual-parallel current trace structure, which, through simulation analysis and experimental verification, utilizes the characteristics of the skin effect to enhance the equivalent magnetic induction detectable by the tunneling magnetoresistance (TMR) current sensor near 1 MHz, thereby improving its frequency response. Compared to traditional single-path current trace, the dual-parallel current trace structure demonstrates superior performance in terms of frequency bandwidth, current sensitivity, and resolution. Based on this novel current trace structure, we design and demonstrate a wideband TMR current sensor with a frequency range of dc-1.5 MHz, which provides a 50% improvement in bandwidth compared to traditional TMR sensor with single-path current trace. Furthermore, the sensor exhibits a full-scale error of no more than 0.4% within the 2.9 A rms range, a minimum resolution close to 5.4 mA, and excellent waveform tracking capability.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 12626-12633
Wideband Tunneling Magnetoresistance Current Sensor With Dual-Parallel Current Trace Utilizing the Skin Effect
In highly integrated switching circuits and power electronic converters, noncontact wideband current sensors are typically required for monitoring operational status. However, the magnetic field distribution of printed circuit board traces is influenced by the skin effect as the current frequency increases, which, in turn, affects the frequency characteristics of the sensor. In this study, we propose a dual-parallel current trace structure, which, through simulation analysis and experimental verification, utilizes the characteristics of the skin effect to enhance the equivalent magnetic induction detectable by the tunneling magnetoresistance (TMR) current sensor near 1 MHz, thereby improving its frequency response. Compared to traditional single-path current trace, the dual-parallel current trace structure demonstrates superior performance in terms of frequency bandwidth, current sensitivity, and resolution. Based on this novel current trace structure, we design and demonstrate a wideband TMR current sensor with a frequency range of dc-1.5 MHz, which provides a 50% improvement in bandwidth compared to traditional TMR sensor with single-path current trace. Furthermore, the sensor exhibits a full-scale error of no more than 0.4% within the 2.9 A rms range, a minimum resolution close to 5.4 mA, and excellent waveform tracking capability.
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (7) , 1289-1292
Low Hysteresis and High Stability in Tunneling Magnetoresistance Vortex Sensors With a Composite Free Layer
The linearity of tunneling magnetoresistance (TMR) sensors is challenging due to the intrinsic magnetic hysteresis of the ferromagnetic Co-Fe-B layer used as the free layer. In this work, by using a composite free layer of Co-Fe-B/Ta/Co-Fe-Si-B with optimized geometric, we demonstrate vortex magnetic states in TMR sensors with large magnetic tunneling junctions, leading to low hysteresis and high stability under external magnetic fields, with a sensitivity of 6 mV/V/Oe (0.6% Oe -1 ) and a nonlinearity below 0.5% FS within ±20 Oe. TMR vortex sensors with a composite free layer could be potentially useful in high precision current sensing in harsh environment.
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (7) , 1289-1292
Low Hysteresis and High Stability in Tunneling Magnetoresistance Vortex Sensors With a Composite Free Layer
The linearity of tunneling magnetoresistance (TMR) sensors is challenging due to the intrinsic magnetic hysteresis of the ferromagnetic Co-Fe-B layer used as the free layer. In this work, by using a composite free layer of Co-Fe-B/Ta/Co-Fe-Si-B with optimized geometric, we demonstrate vortex magnetic states in TMR sensors with large magnetic tunneling junctions, leading to low hysteresis and high stability under external magnetic fields, with a sensitivity of 6 mV/V/Oe (0.6% Oe -1 ) and a nonlinearity below 0.5% FS within ±20 Oe. TMR vortex sensors with a composite free layer could be potentially useful in high precision current sensing in harsh environment.
- 17 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-9
Enhanced Limit-of-Detection of Current Sensor Based on Tunneling Magnetoresistive Effect With Multichips Differential Design
Accurately measuring weak electric currents in the order of mA in a non-invasive manner is crucial yet challenging for industrial electronics. In this work, we first fabricated low-noise magnetic field sensor chips based on the tunneling magnetoresistive (TMR) effect. A composite free layer and a three-step annealing process were used to improve performance, resulting in a sensitivity of 30 V/V/T (3 mV/V/Oe), non-linearity below 0.5%, and reduce the noise density from 1.4 μV/V/√Hz to 0.7 μV/V/√Hz at 1 Hz, in comparison with the traditional two-step annealing process. We then developed a weak-current sensing module with a differential design using two TMR sensor chips arranged antiparallelly. Equipped with a magnetic flux concentration structure and a low-noise signal processing circuit, we demonstrated transient measurement of weak current well below 1 mA with a wide bandwidth of DC-16 kHz, a dynamic range of ±150 mA (51 dB), and a rapid response time of ~30 μs. The limit-of-detection (LoD) of the sensing module for DC and AC current reached 800 μA and 300 μA (RMS), respectively, which is about 30% lower than the single-chip design. This weak-current sensor based on differential TMR has the potential to be useful for industrial applications in smart grids and green energy.
- 17 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-9
Enhanced Limit-of-Detection of Current Sensor Based on Tunneling Magnetoresistive Effect With Multichips Differential Design
Accurately measuring weak electric currents in the order of mA in a non-invasive manner is crucial yet challenging for industrial electronics. In this work, we first fabricated low-noise magnetic field sensor chips based on the tunneling magnetoresistive (TMR) effect. A composite free layer and a three-step annealing process were used to improve performance, resulting in a sensitivity of 30 V/V/T (3 mV/V/Oe), non-linearity below 0.5%, and reduce the noise density from 1.4 μV/V/√Hz to 0.7 μV/V/√Hz at 1 Hz, in comparison with the traditional two-step annealing process. We then developed a weak-current sensing module with a differential design using two TMR sensor chips arranged antiparallelly. Equipped with a magnetic flux concentration structure and a low-noise signal processing circuit, we demonstrated transient measurement of weak current well below 1 mA with a wide bandwidth of DC-16 kHz, a dynamic range of ±150 mA (51 dB), and a rapid response time of ~30 μs. The limit-of-detection (LoD) of the sensing module for DC and AC current reached 800 μA and 300 μA (RMS), respectively, which is about 30% lower than the single-chip design. This weak-current sensor based on differential TMR has the potential to be useful for industrial applications in smart grids and green energy.
- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-9
A Magnetic Field Imaging System Based on TMR Sensors for Banknote Recognition
The high sensitivity and MEMS-compatible process of tunneling magnetoresistance (TMR) sensors provide great opportunities to develop high-resolution magnetic field detection and imaging systems. In this work, we designed a magnetic field imaging (MFI) system based on TMR sensors to detect uniaxial magnetic field components of banknotes including U.S. dollars (USD) and Chinese Yuan (CNY), which clearly reveals the distribution of magnetic anti-counterfeiting markers inside the banknotes. Measurement results of the USD show that the magnetic ink signal is around $\mu \text{T}$ level, and the person portraits on banknotes can be revealed by sensor signals. The testing results of CNY banknotes indicate magnetic color-shifting ink images, as well as a clear magnetic anti-counterfeiting thread. Different from the traditional optical detection, magnetic detection provides unique signals and identification methods. With a satisfactory recognition rate, the proposed MFI system based on TMR sensors demonstrates its promising potential forgery detection and denomination identification of banknotes.
- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-9
A Magnetic Field Imaging System Based on TMR Sensors for Banknote Recognition
The high sensitivity and MEMS-compatible process of tunneling magnetoresistance (TMR) sensors provide great opportunities to develop high-resolution magnetic field detection and imaging systems. In this work, we designed a magnetic field imaging (MFI) system based on TMR sensors to detect uniaxial magnetic field components of banknotes including U.S. dollars (USD) and Chinese Yuan (CNY), which clearly reveals the distribution of magnetic anti-counterfeiting markers inside the banknotes. Measurement results of the USD show that the magnetic ink signal is around $\mu \text{T}$ level, and the person portraits on banknotes can be revealed by sensor signals. The testing results of CNY banknotes indicate magnetic color-shifting ink images, as well as a clear magnetic anti-counterfeiting thread. Different from the traditional optical detection, magnetic detection provides unique signals and identification methods. With a satisfactory recognition rate, the proposed MFI system based on TMR sensors demonstrates its promising potential forgery detection and denomination identification of banknotes.