Lan Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lan Yin has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Yunxin Wu
Light Alloy Research Institute, Central South University, Changsha, China
2 shared publications - Qiumin Xie
School of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China
1 shared publication - Shunli Peng
State Key Laboratory of Precision Manufacturing for Extreme Service Performance, Central South University, Changsha 410083, China
1 shared publication - Tao Zhang
Light Alloy Research Institute, Central South University, Changsha 410083, China
1 shared publication - Yunxin Wu
Light Alloy Research Institute, Central South University, Changsha 410083, People’s Republic of China
1 shared publication - Yutang Wu
School of Mechanical and Electrical Engineering, Central South University, Changsha, China
1 shared publication
Latest Publications
- 1 April 2023
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 59 (4) , 437-446
Enhancement of Rayleigh Wave Generated by Electromagnetic Acoustic Transducer Based on New Magnetic Configuration
Electromagnetic acoustic transducers (EMATs) are widely used to evaluate and detect metal. The ultrasonic signal may be masked by noise for the poor conversion efficiency, which is one of the main obstacles hindering the development of electromagnetic acoustic technique. A type of magnet configuration is utilized to enhance the conversion efficiency in this paper. The magnetic field generated by new EMAT is enhanced. Both the horizontal and vertical magnetic fields are improved. Compared with the conventional configuration EMAT, simulation results show that the amplitude of ultrasonic produced by new EMAT is increased significantly. To further enhance the amplitude of ultrasonic, the effect of magnet parameters on the magnetic field distribution is investigated. Increasing the magnet width and height, and decreasing the distance between the two magnets will improve the magnetic field. Decreasing the distance between magnets allows a stronger magnetic field to participate in the reaction, and the vertical magnetic flux density becomes larger as well. The effect of increasing the width and length of the magnet is similar. The vertical and horizontal magnetic flux density will increase at the same time. It is impossible to enhance the amplitude of the Rayleigh wave unlimitedly by optimizing the parameters. After considering the volume of electromagnetic acoustic transducer and manufacturing, the parameters are determined. Finally, the EMATs corresponding to the conventional and new parameters are used to carry out the experiments whose results indicate that the conversion efficiency is increased by 84% with the new EMAT.
- 1 April 2023
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 59 (4) , 437-446
Enhancement of Rayleigh Wave Generated by Electromagnetic Acoustic Transducer Based on New Magnetic Configuration
Electromagnetic acoustic transducers (EMATs) are widely used to evaluate and detect metal. The ultrasonic signal may be masked by noise for the poor conversion efficiency, which is one of the main obstacles hindering the development of electromagnetic acoustic technique. A type of magnet configuration is utilized to enhance the conversion efficiency in this paper. The magnetic field generated by new EMAT is enhanced. Both the horizontal and vertical magnetic fields are improved. Compared with the conventional configuration EMAT, simulation results show that the amplitude of ultrasonic produced by new EMAT is increased significantly. To further enhance the amplitude of ultrasonic, the effect of magnet parameters on the magnetic field distribution is investigated. Increasing the magnet width and height, and decreasing the distance between the two magnets will improve the magnetic field. Decreasing the distance between magnets allows a stronger magnetic field to participate in the reaction, and the vertical magnetic flux density becomes larger as well. The effect of increasing the width and length of the magnet is similar. The vertical and horizontal magnetic flux density will increase at the same time. It is impossible to enhance the amplitude of the Rayleigh wave unlimitedly by optimizing the parameters. After considering the volume of electromagnetic acoustic transducer and manufacturing, the parameters are determined. Finally, the EMATs corresponding to the conventional and new parameters are used to carry out the experiments whose results indicate that the conversion efficiency is increased by 84% with the new EMAT.
- Open Access
Dynamic Constitutive Relationship of Mg–Gd–Y–Zr–Ag Alloy during High Temperature Deformation Process
The thermal deformation behavior of the Mg–Gd–Y–Zr–Ag alloy was studied by isothermal hot compression tests at high temperatures. The flow stress increased with increased strain rates and decreased temperatures, first increasing and finally remaining stable with increased strain. A hot processing map was built. Using the processing map and microstructural analysis, the temperature should remain at 673–773 K for this alloy to ensure the deformation quality. The primary softening mechanism is discontinuous dynamic recrystallization (DDRX). Rising temperatures and declining strain rates facilitated the emergence and growth of Dynamic recrystallization (DRX) grains. An original JC (O–JC) model and a modified JC (M–JC) model were established. The M–JC model indicated a better prediction than the O–JC model. Still, it was deficient in predicting flow stresses with insufficient coupling effects. Hence, based on the M–JC model, a newly modified JC (NM–JC) model, which further enhances the interaction between strain and strain rate as well as strain and temperature, is proposed. Its projected values can better align with the tested values.
Open AccessDynamic Constitutive Relationship of Mg–Gd–Y–Zr–Ag Alloy during High Temperature Deformation Process
The thermal deformation behavior of the Mg–Gd–Y–Zr–Ag alloy was studied by isothermal hot compression tests at high temperatures. The flow stress increased with increased strain rates and decreased temperatures, first increasing and finally remaining stable with increased strain. A hot processing map was built. Using the processing map and microstructural analysis, the temperature should remain at 673–773 K for this alloy to ensure the deformation quality. The primary softening mechanism is discontinuous dynamic recrystallization (DDRX). Rising temperatures and declining strain rates facilitated the emergence and growth of Dynamic recrystallization (DRX) grains. An original JC (O–JC) model and a modified JC (M–JC) model were established. The M–JC model indicated a better prediction than the O–JC model. Still, it was deficient in predicting flow stresses with insufficient coupling effects. Hence, based on the M–JC model, a newly modified JC (NM–JC) model, which further enhances the interaction between strain and strain rate as well as strain and temperature, is proposed. Its projected values can better align with the tested values.
- Open Access
Comparison of Constitutive Models and Microstructure Evolution of GW103K Magnesium Alloy during Hot Deformation
The characteristics of constitutive behavior and microstructure evolution of GW103K magnesium alloy were investigated via hot compression tests at a strain rate of 0.001–1 s−1 and a temperature of 623–773 K. The rheological stress of GW103K alloy decreased with increasing temperature or decreasing strain rate during hot deformation. Three models including the Johnson Cook (JC) model, the strain-compensated Arrhenius (SCA) model and back-propagation neural networks (BPNN) were applied to describe the constitutive relationships. Subsequently, the predictability and precision of the models were compared by evaluating the correlation coefficient (R), root mean square errors (RMSE), and relative errors (RE). Compared with the JC and SCA models, the BPNN model was more efficient and had higher prediction accuracy in describing flow stress behavior. Furthermore, EBSD maps confirmed that magnesium alloy easily causes dynamic recrystallization (DRX) during hot deformation. The volume fraction and size of DRX grains increased with decreasing strain rate and/or increasing temperature.
Open AccessComparison of Constitutive Models and Microstructure Evolution of GW103K Magnesium Alloy during Hot Deformation
The characteristics of constitutive behavior and microstructure evolution of GW103K magnesium alloy were investigated via hot compression tests at a strain rate of 0.001–1 s−1 and a temperature of 623–773 K. The rheological stress of GW103K alloy decreased with increasing temperature or decreasing strain rate during hot deformation. Three models including the Johnson Cook (JC) model, the strain-compensated Arrhenius (SCA) model and back-propagation neural networks (BPNN) were applied to describe the constitutive relationships. Subsequently, the predictability and precision of the models were compared by evaluating the correlation coefficient (R), root mean square errors (RMSE), and relative errors (RE). Compared with the JC and SCA models, the BPNN model was more efficient and had higher prediction accuracy in describing flow stress behavior. Furthermore, EBSD maps confirmed that magnesium alloy easily causes dynamic recrystallization (DRX) during hot deformation. The volume fraction and size of DRX grains increased with decreasing strain rate and/or increasing temperature.