PAParviz Amiri

Parviz Amiri

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Parviz Amiri has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Low-Power, Low-Noise Recycling Folded-Cascode Operational Transconductance Amplifier for Neural Recording Applications

    by Amir Moosaei, Mohammad Hossein Maghami, Ali Nejati, Parviz Amiri, Mohamad Sawan

    We present in this paper a low-noise, low-power CMOS operational transconductance amplifier designed for the preconditioning stage of implantable neural recording microsystems. The proposed single-stage amplifier utilizes a combination of recently published techniques, including cross-coupled devices in a recycling folded-cascode topology with positive feedback, to achieve high DC voltage gain and unity-gain bandwidth while minimizing power consumption. A mixed N-type and P-type MOSFET input stage enhances input common-mode performance. Designed and implemented in a 0.18-µm CMOS process with a 1.8 V supply, post-layout simulations demonstrate an open-loop voltage gain of 97.23 dB, a 2.91 MHz unity-gain bandwidth (with a 1 pF load), and an input-referred noise of 4.75 μVrms. The total power dissipation, including bias circuitry, is 5.43 μW, and the amplifier occupies a chip area of 0.0055 mm2. Integrated into a conventional neural recording amplifier configuration, the proposed amplifier achieves a simulated input-referred noise of 5.73 µVrms over a 1 Hz to 10 kHz bandwidth with a power consumption of 5.6 µW. This performance makes it suitable for amplifying both action potential and local field potential signals. The amplifier provides an output voltage swing of 0.976 Vpp with a total harmonic distortion of −62.68 dB at 1 kHz.


  • Open Access

    Comparative Survey of Embedded System Implementations of Convolutional Neural Networks in Autonomous Cars Applications

    by Mohammad Cheshfar, Mohammad Hossein Maghami, Parviz Amiri, Hossein Gharaee Garakani, Luciano Lavagno

    In the rapidly evolving field of autonomous cars, advanced deep learning systems have ushered in a new era of innovation, enabling the integration of unique features into vehicles. These advancements span various areas, including pedestrian and vehicle detection, recognition of road signs and driving patterns, identification of drivable roads and scenes, and improved mapping and routing techniques. However, the high computational requirements of deep learning networks present a significant challenge, especially for embedded systems like FPGAs (Field-Programmable Gate Arrays) that have limited capacity. Addressing this challenge, this article presents a comprehensive survey of the methodologies employed in implementing Convolutional Neural Networks (CNNs) on resource-constrained processors, within the domain of self-driving car applications. Our survey encompasses a thorough review of the existing literature in the field of deep learning applied to autonomous cars, from perception to localization, with a specific emphasis on implementations utilizing embedded hardware such as FPGAs and embedded GPUs. Furthermore, we present and analyze results that elucidate the intricate trade-offs between latency, energy consumption, and the judicious selection of the underlying platform. These insights are crucial for researchers and practitioners in the field, as they provide a clear direction for optimizing the performance of deep learning networks on resource-constrained platforms, ultimately contributing to the advancement of self-driving car technologies.


  • Open Access

    A 13.56 MHz Low-Power, Single-Stage CMOS Voltage-Boosting Rectifier for Wirelessly Powered Biomedical Implants

    by Seyed Morteza Hosseini, Mohammad Hossein Maghami, Parviz Amiri, Mohamad Sawan

    In this paper, a low-power, single-stage, active rectifier based on a new charge-pump circuit is presented to be used in biomedical implants. The proposed circuit not only rectifies the AC input voltage to a DC voltage but also amplifies the DC output voltage to a higher level. Low-loss MOS switches are used in the structure of the designed circuit to provide high power conversion efficiency. In addition, by using two comparators, the reverse leakage current is somehow eliminated, resulting in a higher increase in the power efficiency. By tying the source and bulk terminals of the utilized transistors, the body effect problem has been solved, and by connecting the p-substrate to the ground, which is the lowest voltage in the circuit, the latch-up phenomenon is eliminated without any extra circuit. The proposed rectifier is implemented and post-layout simulated in a 0.18 µm standard CMOS technology. According to the simulation results, 1.205 V output DC voltage is achieved from an AC input signal with the peak-to-peak amplitude of 1 V at the operating frequency of 13.56 MHz with a 3 kΩ load resistance. The total active area of the designed circuit is 0.167 mm2 with a maximum power conversion efficiency of 98.2%, output power in the range of 0.5–1.5 mW, and voltage conversion ratio of 120%.


  • Design a novel digital sliding mode predictive control for buck converter

    by Mahnaz Janipoor Deylamani, Parviz Amiri, Mohammad Hossein Refan

    In this paper, a new discrete-time sliding mode predictive control (DSMPC) strategy with a PID sliding function is proposed for synchronous dc-dc buck converter, and its stability analysis is reported. The model predictive control, along with digital sliding mode control (DSMC), is able to further reducing the chattering phenomenon, steady-state error, overshoot, and undershoot. The proposed control method implementation only requires output error voltage evaluation. The effectiveness of the proposed DSMPC is proved through simulation results executed by the MATLAB/SIMULINK software. These results demonstrate its superior performance to DSMC. In other words, it represents a significant reduction of the chattering, overshoot, and undershoots of output voltage response by an optimized control law during load and line variations. The proposed DSMPC almost overcomes the steady-state error (0.02%) and decreases the ripple value to about 0.2%. The overshoot and undershoot are 1.5% and 1%, respectively. Moreover, when the input voltage is changed by 26%, there is approximately no overshoot and undershoot. Also, some experimental results are presented to further illustrate the effectiveness of the proposed system. Experimental studies have been performed using a Spartan-6 field programmable gate array (FPGA) platform by Xilinx for the implementation of the digital control and relevant logic.


  • Open Access

    An Ultra-Low-Power Area-Efficient Non-Coherent Binary Phase-Shift Keying Demodulator for Implantable Biomedical Microsystems

    by Milad Ghazi, Mohammad Hossein Maghami, Parviz Amiri, Sotoudeh Hamedi-Hagh

    A novel non-coherent, low-power, area-efficient binary phase-shift keying demodulator for wireless implantable biomedical microsystems is proposed. The received data and synchronized clock signal are detected using a delayed digitized format of the input signal. The proposed technique does not require any kind of oscillator circuit, and due to the synchronization of all circuit signals, the proposed demodulator can work in a wide range of biomedical data telemetry common frequencies in different process/temperature corners. The presented circuit has been designed and post-layout-simulated in a standard 0.18 μm CMOS technology and occupies 17 × 27 μm2 of active area. Post-layout simulation results indicate that with a 1.8 V power supply, power consumption of the designed circuit is 8.5 μW at a data rate of 20 Mbps. The presented demodulation scheme was also implemented on a proof-of-concept circuit board for verifying its functionality.


  • Open Access

    A Sub-Threshold Differential CMOS Schmitt Trigger with Adjustable Hysteresis Based on Body Bias Technique

    by Sara Radfar, Ali Nejati, Yasin Bastan, Parviz Amiri, Mohammad Hossein Maghami, Mehdi Nasrollahpour, Sotoudeh Hamedi-Hagh

    This paper presents a sub-threshold differential CMOS Schmitt trigger with tunable hysteresis, which can be used to enhance the noise immunity of low-power electronic systems. By exploiting the body bias technique to the positive feedback transistors, the hysteresis of the proposed Schmitt trigger is generated, and it can be adjusted by the applied bias voltage to the bulk terminal of the utilized PMOS transistors. The principle of operation and the main formulas of the proposed circuit are discussed. The circuit is designed in a 0.18-μm standard CMOS process with a 0.6 V power supply. Post-layout simulation results show that the hysteresis width of the Schmitt trigger can be adjusted from 45.5 mV to 162 mV where the ratio of the hysteresis width variation to supply voltage is 19.4%. This circuit consumes 10.52 × 7.91 μm2 of silicon area, and its power consumption is only 1.38 µW, which makes it a suitable candidate for low-power applications such as portable electronic, biomedical, and bio-implantable systems.