Samet Kaya Dursun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Samet Kaya Dursun has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Muhammed Taşova
Faculty of Agriculture, Department of Biosystems Engineering, Tokat Gaziosmanpaşa University, Tokat, Turkey
18 shared publications - Burcu Aksüt
Tokat Gaziosmanpaşa University, Faculty of Agriculture, Department of Horticulture, Tokat
4 shared publications - Hakan Polatcı
Tokat Gaziosmanpaşa Üniversitesi
2 shared publications - Onur Saraçoğlu
Tokat Gaziosmanpaşa Üniversitesi
2 shared publications Burcu Aksüt
Tokat Gaziosmanpaşa University Agricultural Faculty Horticulture Department Sustainable Agriculture Program 60250 Tokat/ Türkiye
1 shared publication- Edanur Türk
Tokat Gaziosmanpaşa University, Faculty of Agriculture, Department of Biosystems Engineering, Tokat, Turkey
1 shared publication
Latest Publications
- 29 October 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (11)
Microwave‐Assisted Drying of Kiwifruit: Effects of Microwave Power on Functional Properties and Energy Consumption
This study investigated the effects of different microwave power levels (360, 540, 720, and 900 W) on the functional, physicochemical, and bioactive properties of kiwifruit powders, as well as energy consumption kinetics during drying. Power‐dependent color changes were observed: loss in greenness ( +a ) increased at 540 and 900 W, whereas +b and chroma values decreased at 900 W. HR values (1.10–1.22) indicated acceptable flowability across all treatments, with no significant differences in flow properties. Water activity (aw) reached its minimum at 720 W, while hygroscopicity peaked at this level. Water holding capacity (WHC) was highest at 720 W (5.52 g water/g), whereas oil holding capacity (OHC) (4.25 g oil/g) and water solubility index (WSI) (57.43%) peaked at 900 W. Total phenolic content (TPC) increased up to 720 W (1132.5 mg GAE/100 g) and remained statistically unchanged at 900 W. DPPH activity showed no significant difference between 720 and 900 W, while FRAP reached its maximum at 900 W (38.63 μmol TE/g). Energy analysis revealed that higher powers (720–900 W) produced elevated SMER values initially due to rapid moisture removal. However, SEC increased sharply in later drying stages, particularly at 900 W, reducing energy efficiency. Overall, 720 W favored several quality parameters, whereas 540 W offered a better energy‐efficiency profile. Since no single power level was superior across all parameters, balancing product quality and energy performance is essential for kiwifruit powder production.
- 29 October 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (11)
Microwave‐Assisted Drying of Kiwifruit: Effects of Microwave Power on Functional Properties and Energy Consumption
This study investigated the effects of different microwave power levels (360, 540, 720, and 900 W) on the functional, physicochemical, and bioactive properties of kiwifruit powders, as well as energy consumption kinetics during drying. Power‐dependent color changes were observed: loss in greenness ( +a ) increased at 540 and 900 W, whereas +b and chroma values decreased at 900 W. HR values (1.10–1.22) indicated acceptable flowability across all treatments, with no significant differences in flow properties. Water activity (aw) reached its minimum at 720 W, while hygroscopicity peaked at this level. Water holding capacity (WHC) was highest at 720 W (5.52 g water/g), whereas oil holding capacity (OHC) (4.25 g oil/g) and water solubility index (WSI) (57.43%) peaked at 900 W. Total phenolic content (TPC) increased up to 720 W (1132.5 mg GAE/100 g) and remained statistically unchanged at 900 W. DPPH activity showed no significant difference between 720 and 900 W, while FRAP reached its maximum at 900 W (38.63 μmol TE/g). Energy analysis revealed that higher powers (720–900 W) produced elevated SMER values initially due to rapid moisture removal. However, SEC increased sharply in later drying stages, particularly at 900 W, reducing energy efficiency. Overall, 720 W favored several quality parameters, whereas 540 W offered a better energy‐efficiency profile. Since no single power level was superior across all parameters, balancing product quality and energy performance is essential for kiwifruit powder production.
- 16 September 2026
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 62 (10) , 147
Temperature-controlled microwave drying as a novel route to functional pomegranate peel: kinetic, energy consumption, quality
- 16 September 2026
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 62 (10) , 147
Temperature-controlled microwave drying as a novel route to functional pomegranate peel: kinetic, energy consumption, quality
- 20 August 2026
- Published by Gaziosmanpasa University in Journal of Agricultural Faculty of Gaziosmanpasa University
- Vol. 43 (2) , 116-122
Assessment of the effects of drying temperatures on effective moisture diffusion and quality properties of purple carrot slices dried by hot air method
This study examined the influence of hot-air drying temperature on the moisture ratio (MR), drying rate (DR), effective moisture diffusivity (Deff), color characteristics (L, a, b, C, and ΔE), and hardness (N) of purple carrot slices. A clear temperature-dependent response was observed for both the drying behavior and the quality attributes of the samples. Increasing the drying-air temperature resulted in a shorter drying period. The mean DR values obtained under the different drying conditions ranged from 0.0062 to 0.0201 g moisture/g dry matter·min. The calculated Deff values were within the range of 9.66 × 10⁻⁹ to 3.37 × 10⁻⁸ m²/s. Temperature also altered the color characteristics of the fresh purple carrot slices; specifically, the L and b values differed significantly from those of the fresh samples (p < 0.05). The α color values of fresh samples were preserved at 55 ºC and 65 ºC, the C color value at 55 ºC, and the ΔE color value at 55 ºC (p>0.05). The N values of fresh purple carrot slices are preserved at 75 ºC (p<0.05). Based on the findings, a temperature of 75 °C is recommended for the MR, DR, Deff, and N parameters, while a temperature of 55 °C is recommended for color characteristics.
- 20 August 2026
- Published by Gaziosmanpasa University in Journal of Agricultural Faculty of Gaziosmanpasa University
- Vol. 43 (2) , 116-122
Assessment of the effects of drying temperatures on effective moisture diffusion and quality properties of purple carrot slices dried by hot air method
This study examined the influence of hot-air drying temperature on the moisture ratio (MR), drying rate (DR), effective moisture diffusivity (Deff), color characteristics (L, a, b, C, and ΔE), and hardness (N) of purple carrot slices. A clear temperature-dependent response was observed for both the drying behavior and the quality attributes of the samples. Increasing the drying-air temperature resulted in a shorter drying period. The mean DR values obtained under the different drying conditions ranged from 0.0062 to 0.0201 g moisture/g dry matter·min. The calculated Deff values were within the range of 9.66 × 10⁻⁹ to 3.37 × 10⁻⁸ m²/s. Temperature also altered the color characteristics of the fresh purple carrot slices; specifically, the L and b values differed significantly from those of the fresh samples (p < 0.05). The α color values of fresh samples were preserved at 55 ºC and 65 ºC, the C color value at 55 ºC, and the ΔE color value at 55 ºC (p>0.05). The N values of fresh purple carrot slices are preserved at 75 ºC (p<0.05). Based on the findings, a temperature of 75 °C is recommended for the MR, DR, Deff, and N parameters, while a temperature of 55 °C is recommended for color characteristics.
- 3 June 2026
- Published by Hatay Mustafa Kemal University in Mustafa Kemal Üniversitesi Tarım Bilimleri Dergisi
- Vol. 31 (2) , 259-270
Farklı kurutma yöntemi ve taşıyıcı ajan oranlarıyla üretilen kavun tozunun kinetik, enerji tüketimi ve renk değerleri açısından kıyaslanması
Kurutma, kısaca taze üründen fazla nemi uzaklaştırma işlemi olarak tanımlanabilir. Bu çalışmada, kavun püreleri tozu üretmek için konvektif ve sıcaklık kontrollü mikrodalga kurutucuda 70 ºC sıcaklıkta farklı oranlarda (%5 ve %10) taşıyıcı ajan (sorbitol) ekleyerek kurutulmuştur. Üretilen kavun tozlarının kuruma kinetiği, enerji analizleri ve renk parametleri araştırılmıştır. Kurutma işlemleri arasında en kısa kuruma süresi 38 dakika ile %10 oranında sorbitol eklenerek sıcaklık kontrollü mikrodalga kurutucuda kurutulan örneklerde tespit edilmiştir. Kavun kurutma işlemlerinin kuruma oranları 0.0142-0.1754 g nem g kuru madde-1.dakika arasında değiştiği belirlenmiştir. Efektif difüzyon değerleri 7.05×10-8 ile 7.12x10-7 m2 s-1 arasında değişken değerler aldığı tespit edilmiştir. Kurutma işlemlerine ait ortalama özgül nem çekme aranı ve özgül enerji tüketim değerleri sırasıyla 0.0048-0.0144 kg kWh-1 ve 69.55-210.19 kWh kg-1 aralıklarında değiştiği belirlenmiştir. Üretilen kavun tozlarının sarı/mavi (b) ve kroma (C) renk değerleri açısından istatistiksel olarak anlamlı (p
- 3 June 2026
- Published by Hatay Mustafa Kemal University in Mustafa Kemal Üniversitesi Tarım Bilimleri Dergisi
- Vol. 31 (2) , 259-270
Farklı kurutma yöntemi ve taşıyıcı ajan oranlarıyla üretilen kavun tozunun kinetik, enerji tüketimi ve renk değerleri açısından kıyaslanması
Kurutma, kısaca taze üründen fazla nemi uzaklaştırma işlemi olarak tanımlanabilir. Bu çalışmada, kavun püreleri tozu üretmek için konvektif ve sıcaklık kontrollü mikrodalga kurutucuda 70 ºC sıcaklıkta farklı oranlarda (%5 ve %10) taşıyıcı ajan (sorbitol) ekleyerek kurutulmuştur. Üretilen kavun tozlarının kuruma kinetiği, enerji analizleri ve renk parametleri araştırılmıştır. Kurutma işlemleri arasında en kısa kuruma süresi 38 dakika ile %10 oranında sorbitol eklenerek sıcaklık kontrollü mikrodalga kurutucuda kurutulan örneklerde tespit edilmiştir. Kavun kurutma işlemlerinin kuruma oranları 0.0142-0.1754 g nem g kuru madde-1.dakika arasında değiştiği belirlenmiştir. Efektif difüzyon değerleri 7.05×10-8 ile 7.12x10-7 m2 s-1 arasında değişken değerler aldığı tespit edilmiştir. Kurutma işlemlerine ait ortalama özgül nem çekme aranı ve özgül enerji tüketim değerleri sırasıyla 0.0048-0.0144 kg kWh-1 ve 69.55-210.19 kWh kg-1 aralıklarında değiştiği belirlenmiştir. Üretilen kavun tozlarının sarı/mavi (b) ve kroma (C) renk değerleri açısından istatistiksel olarak anlamlı (p
- Open Access
- 28 August 2025
- Published by Turkish Science and Technology Publishing (TURSTEP) in Turkish Journal of Agriculture - Food Science and Technology
- Vol. 13 (8) , 2187-2193
Assessment of Experimental Energy Consumption and Drying Kinetics Analyses of Processing Waste Pea (Pisum sativum) by Convective Drying
Shelled pea is an important product due to the nutritional values it contains, and it is not possible to consume for a long time due to its high moisture content. For this reason, it can be consumed out of season after drying. In this study, the effect of potassium carbonate and microwave pretreatment was investigated by drying in a cyclone type convective dryer at air flow rates of 287.50, 575.00 and 862.50 m3/h to produce dry peas. The moisture content, drying rate, effective moisture diffusion, specific moisture absorption rate (SMER), specific energy consumption (SEC) and color properties of the drying processes were investigated. Air flows and pretreatments affected the drying kinetics, color and energy analysis of the drying processes. Drying rate values for drying processes varied between 0.01190-0.0237 g moisture/g dry matter per minute. It was determined that the effective moisture diffusion values varied between 7.60×10-8-1.24×10-7 m2/s. Drying processes did not preserve the color values compared to fresh (p<0.05). It has been determined that the SMER values of the drying processes vary between 4.10-8.10×10-4 kg/kWh and the SEC values vary between 1230.59-2451.15 kWh/kg. According to the findings obtained within the scope of the study, it is recommended to dry the shelled peas at 862.50 m3/h air flow rate and after dipping into potassium carbonate solution.
- 28 August 2025
- Published by Turkish Science and Technology Publishing (TURSTEP) in Turkish Journal of Agriculture - Food Science and Technology
- Vol. 13 (8) , 2187-2193
Open AccessAssessment of Experimental Energy Consumption and Drying Kinetics Analyses of Processing Waste Pea (Pisum sativum) by Convective Drying
Shelled pea is an important product due to the nutritional values it contains, and it is not possible to consume for a long time due to its high moisture content. For this reason, it can be consumed out of season after drying. In this study, the effect of potassium carbonate and microwave pretreatment was investigated by drying in a cyclone type convective dryer at air flow rates of 287.50, 575.00 and 862.50 m3/h to produce dry peas. The moisture content, drying rate, effective moisture diffusion, specific moisture absorption rate (SMER), specific energy consumption (SEC) and color properties of the drying processes were investigated. Air flows and pretreatments affected the drying kinetics, color and energy analysis of the drying processes. Drying rate values for drying processes varied between 0.01190-0.0237 g moisture/g dry matter per minute. It was determined that the effective moisture diffusion values varied between 7.60×10-8-1.24×10-7 m2/s. Drying processes did not preserve the color values compared to fresh (p<0.05). It has been determined that the SMER values of the drying processes vary between 4.10-8.10×10-4 kg/kWh and the SEC values vary between 1230.59-2451.15 kWh/kg. According to the findings obtained within the scope of the study, it is recommended to dry the shelled peas at 862.50 m3/h air flow rate and after dipping into potassium carbonate solution.
- Open Access
- 26 March 2025
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (16) , 22865-22875
Evaluation of the drying kinetics, energy consumption and physicochemical properties of Golden delicious apple powders by mixing carrier agents
In this study, the effects of carrier agents and their usage methods on the drying rate, moisture content, effective moisture diffusion, energy consumption, color, density, Carr (CI) and Hausner (HR) index values of Golden delicious variety apple powder produced by convective drying method at 60 °C and 80 °C were compared. The effects of maltodextrin (M), sorbitol (S) and lactose (L) carrier agents and their M + S, M + L, S + L and M + S + L usage methods in powder production were determined. In the drying processes, purees were dried from an average of 4.77 ± 0.30 g moisture/g dry matter to 0.005 ± 0.0001 moisture/dry matter. It was found that the average drying rates of the samples varied between 6.77 × 10−3 and 1.44 × 10−2 g moisture/g dry matter.min. The effective moisture diffusion values were determined to vary between 2.31 and 4.91 × 10−6 m2/s. The average specific moisture absorption ratio (SMER) values of the drying processes were determined to vary between 0.0027 and 0.0045 kg/kWh and the specific energy consumption (SEC) values were determined to vary between 220.89 and 393.22 kWh/kg. The tapped density values of the powder samples varied between 0.75 and 1.09 g/cm3 and the bulk density values between 0.67 and 0.82 g/cm3. The CI values of apple powders were determined between 1.35 and 38.96% and the HR values were determined between 1.01 and 1.69. The powder samples preserved the L, a and C color values of fresh significantly (p < 0.05). The powders produced under 60 °C-Sorbitol, 60 °C-Lactose and 80 °C-Maltose conditions preserved the b color value of freshness significantly (p < 0.05).
- 26 March 2025
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (16) , 22865-22875
Open AccessEvaluation of the drying kinetics, energy consumption and physicochemical properties of Golden delicious apple powders by mixing carrier agents
In this study, the effects of carrier agents and their usage methods on the drying rate, moisture content, effective moisture diffusion, energy consumption, color, density, Carr (CI) and Hausner (HR) index values of Golden delicious variety apple powder produced by convective drying method at 60 °C and 80 °C were compared. The effects of maltodextrin (M), sorbitol (S) and lactose (L) carrier agents and their M + S, M + L, S + L and M + S + L usage methods in powder production were determined. In the drying processes, purees were dried from an average of 4.77 ± 0.30 g moisture/g dry matter to 0.005 ± 0.0001 moisture/dry matter. It was found that the average drying rates of the samples varied between 6.77 × 10−3 and 1.44 × 10−2 g moisture/g dry matter.min. The effective moisture diffusion values were determined to vary between 2.31 and 4.91 × 10−6 m2/s. The average specific moisture absorption ratio (SMER) values of the drying processes were determined to vary between 0.0027 and 0.0045 kg/kWh and the specific energy consumption (SEC) values were determined to vary between 220.89 and 393.22 kWh/kg. The tapped density values of the powder samples varied between 0.75 and 1.09 g/cm3 and the bulk density values between 0.67 and 0.82 g/cm3. The CI values of apple powders were determined between 1.35 and 38.96% and the HR values were determined between 1.01 and 1.69. The powder samples preserved the L, a and C color values of fresh significantly (p < 0.05). The powders produced under 60 °C-Sorbitol, 60 °C-Lactose and 80 °C-Maltose conditions preserved the b color value of freshness significantly (p < 0.05).
- Open Access
- 29 January 2025
- Published by Tekirdag Ziraat Fakultesi Dergisi in Tekirdağ Ziraat Fakültesi Dergisi
- Vol. 22 (1) , 257-267
Mikrodalga Kurutma Yöntemiyle Üretilen Karpuz Cipslerinde Güç değerlerinin Kuruma Kinetikleri, Enerji Tüketimi ve Renk Kriterleri Özelliklerine Etkisi
Karpuz birçok besin değerini bünyesinde barındıran ve bol sulu kabakgillerden olan tarımsal bir üründür. Karpuz cipsi üretiminin gelişmesi hem ülke olarak hem de küresel boyutta taze ürünlere alternatif fonksiyonel bir gıda olması açısından önemlidir. Bu çalışmada, karpuz cipsi üretimi için mikrodalga tekniği kullanılarak 180, 360 ve 540 W güç değerlerinde taze karpuz dilimleri kurutulmuştur. Çalışmanın amacı, karpuz cipsi üretiminde kinetik, kalite özellikleri ve enerji tüketim parametreleri açısından en uygun mikrodalga güç seviyesini tespit etmektir. Kurutma işlemlerinde için kuruma süresi, kuruma oranı, nem oranı, renk parametreleri, efektif nem difüzyonu, özgül nem çekme oranı (SMER) ve özgül enerji tüketimi (SEC) değerleri belirlenmiştir. Karpuz cipsi üretiminde en kısa kuruma süresi 540 W güçte kurutulan örneklerde 11 dakika olarak belirlenmiştir. En uzun kuruma süresi ise 180 W güçte 48.50 dakika olarak belirlenmiştir. Kurutma işlemlerinde 180, 360 ve 540 W mikrodalga güç değerleri için tespit edilen kuruma oranları sırayla 0.200, 0.530 ve 0.939 g nem g kuru madde.dakika-1 olarak tespit edilmiştir. Taze karpuz dilimlerin L, a ve b değerleri sırasıyla 43.17, 31.32 ve 20.59 olarak belirlenmiştir. Taze dilimlere en yakın renk değerleri 360 W güç değerinde kurutulan örneklerde belirlenmiştir. Mikrodalgada 360 W güç değerinde kurutulan örneklerin L, a ve b değerleri sırasıyla 41.35, 16.56 ve 12.07 olarak tespit edilmiştir. Kurutma işlemlerinin efektif nem difüzyon değerlerinin 3.74x10-11-2.27.10-10 m2.s-1 arasında değiştiği tespit edilmiştir. En yüksek özgül nem çekme oranı (SMER) 540 W güçte kurutulan örneklerde ortalama 0.0662 kg.kWh-1 olarak belirlenmiştir. En düşük özgül enerji tüketim (SEC) değeri 540 W güçte kurutulan örneklerde 14.52 kW.kg-1 olarak hesaplanmıştır. Bu çalışmada kuruma süresi, efektif nem difüzyonu ve enerji parametreleri açısından karpuz dilimlerinin mikrodalgada 540 W güç değerinde kurutulması önerilmektedir. Renk değerleri açısından karpuz cipsi üretiminde 360 W mikrodalga güç değerinde kurutulması önerilmektedir.
- 29 January 2025
- Published by Tekirdag Ziraat Fakultesi Dergisi in Tekirdağ Ziraat Fakültesi Dergisi
- Vol. 22 (1) , 257-267
Open AccessMikrodalga Kurutma Yöntemiyle Üretilen Karpuz Cipslerinde Güç değerlerinin Kuruma Kinetikleri, Enerji Tüketimi ve Renk Kriterleri Özelliklerine Etkisi
Karpuz birçok besin değerini bünyesinde barındıran ve bol sulu kabakgillerden olan tarımsal bir üründür. Karpuz cipsi üretiminin gelişmesi hem ülke olarak hem de küresel boyutta taze ürünlere alternatif fonksiyonel bir gıda olması açısından önemlidir. Bu çalışmada, karpuz cipsi üretimi için mikrodalga tekniği kullanılarak 180, 360 ve 540 W güç değerlerinde taze karpuz dilimleri kurutulmuştur. Çalışmanın amacı, karpuz cipsi üretiminde kinetik, kalite özellikleri ve enerji tüketim parametreleri açısından en uygun mikrodalga güç seviyesini tespit etmektir. Kurutma işlemlerinde için kuruma süresi, kuruma oranı, nem oranı, renk parametreleri, efektif nem difüzyonu, özgül nem çekme oranı (SMER) ve özgül enerji tüketimi (SEC) değerleri belirlenmiştir. Karpuz cipsi üretiminde en kısa kuruma süresi 540 W güçte kurutulan örneklerde 11 dakika olarak belirlenmiştir. En uzun kuruma süresi ise 180 W güçte 48.50 dakika olarak belirlenmiştir. Kurutma işlemlerinde 180, 360 ve 540 W mikrodalga güç değerleri için tespit edilen kuruma oranları sırayla 0.200, 0.530 ve 0.939 g nem g kuru madde.dakika-1 olarak tespit edilmiştir. Taze karpuz dilimlerin L, a ve b değerleri sırasıyla 43.17, 31.32 ve 20.59 olarak belirlenmiştir. Taze dilimlere en yakın renk değerleri 360 W güç değerinde kurutulan örneklerde belirlenmiştir. Mikrodalgada 360 W güç değerinde kurutulan örneklerin L, a ve b değerleri sırasıyla 41.35, 16.56 ve 12.07 olarak tespit edilmiştir. Kurutma işlemlerinin efektif nem difüzyon değerlerinin 3.74x10-11-2.27.10-10 m2.s-1 arasında değiştiği tespit edilmiştir. En yüksek özgül nem çekme oranı (SMER) 540 W güçte kurutulan örneklerde ortalama 0.0662 kg.kWh-1 olarak belirlenmiştir. En düşük özgül enerji tüketim (SEC) değeri 540 W güçte kurutulan örneklerde 14.52 kW.kg-1 olarak hesaplanmıştır. Bu çalışmada kuruma süresi, efektif nem difüzyonu ve enerji parametreleri açısından karpuz dilimlerinin mikrodalgada 540 W güç değerinde kurutulması önerilmektedir. Renk değerleri açısından karpuz cipsi üretiminde 360 W mikrodalga güç değerinde kurutulması önerilmektedir.