Di Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Di Zhang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Aobo Liu
The State Key Laboratory of Tribology, Tsinghua University, Beijing, People's Republic of China
1 shared publicationBangzhao Yin
The State Key Laboratory of Tribology, Tsinghua University, Beijing, People's Republic of China
1 shared publication- Bofang Zheng
School of Materials Science and Engineering, Tianjin University, Tianjin 300350, China
1 shared publication - Peng Wen
Department of Mechanical Engineering, Tsinghua University, Beijing, China
1 shared publication - Sansan Ao
School of Materials Science and Engineering, Tianjin University, Tianjin 300350, China
1 shared publication - Sunusi Marwana Manladan
School of Materials Science and Engineering, Tianjin University, Tianjin 300350, China
1 shared publication
Latest Publications
- 1 May 2023
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 28 (4) , 268-276
Microstructure, mechanical and electrochemical properties of wire-arc additively manufactured duplex stainless steel
Wire-arc additively manufactured (WAAM) super duplex stainless steels (DSS) 2594 walls were fabricated to investigate the microstructure of different regions, including top, body and root as well as the influence of microstructure on mechanical and electrochemical properties. The microstructure was composed of ferrite and austenite with a few nitride precipitates. The ferrite content decreased from top to root. The average hardness increased slightly from top to root. The ultimate tensile strength of different regions varied slightly, comparable to that of the hot-rolled plate. Compared with those in vertical direction, samples in the horizontal direction had higher strength and lower elongation. The corrosion resistance ranked as root ≈ body > hot-rolled > top.
- 1 May 2023
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 28 (4) , 268-276
Microstructure, mechanical and electrochemical properties of wire-arc additively manufactured duplex stainless steel
Wire-arc additively manufactured (WAAM) super duplex stainless steels (DSS) 2594 walls were fabricated to investigate the microstructure of different regions, including top, body and root as well as the influence of microstructure on mechanical and electrochemical properties. The microstructure was composed of ferrite and austenite with a few nitride precipitates. The ferrite content decreased from top to root. The average hardness increased slightly from top to root. The ultimate tensile strength of different regions varied slightly, comparable to that of the hot-rolled plate. Compared with those in vertical direction, samples in the horizontal direction had higher strength and lower elongation. The corrosion resistance ranked as root ≈ body > hot-rolled > top.
- Open Access
Narrow Gap Welding of X80 Steel Using Laser-CMT Hybrid Welding with Misaligned Laser and Arc
The feasibility of using laser-cold metal transfer (CMT) misaligned hybrid welding to join an X80 line-pipe steel in a narrow gap configuration was investigated. The laser beam interacted with the sidewall and its bottom at a small angle, while the CMT arc acted on the backside of the laser beam. The influence of the distance parameter between the laser spot and the tip of the welding wire on the formation and defects of the filled weld were investigated. Narrow gap bevel welds were performed, and the joints were tensile and had a satisfactory Charpy impact score. The tensile fracture is located in the base metal, and the impact fracture is a ductile fracture. Under this condition, the heat input could be efficiently reduced, preventing the formation of defects such as lack of fusion and reducing the number of pores. Additionally, welds with a narrow heat affect zone (HAZ) could be obtained. The results reveal that the hybrid process, as a low-heat input method, is suitable for narrow gap welding.
Open AccessNarrow Gap Welding of X80 Steel Using Laser-CMT Hybrid Welding with Misaligned Laser and Arc
The feasibility of using laser-cold metal transfer (CMT) misaligned hybrid welding to join an X80 line-pipe steel in a narrow gap configuration was investigated. The laser beam interacted with the sidewall and its bottom at a small angle, while the CMT arc acted on the backside of the laser beam. The influence of the distance parameter between the laser spot and the tip of the welding wire on the formation and defects of the filled weld were investigated. Narrow gap bevel welds were performed, and the joints were tensile and had a satisfactory Charpy impact score. The tensile fracture is located in the base metal, and the impact fracture is a ductile fracture. Under this condition, the heat input could be efficiently reduced, preventing the formation of defects such as lack of fusion and reducing the number of pores. Additionally, welds with a narrow heat affect zone (HAZ) could be obtained. The results reveal that the hybrid process, as a low-heat input method, is suitable for narrow gap welding.