NDNatalia Yu. Dudareva

Natalia Yu. Dudareva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Natalia Yu. Dudareva has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Influence of Aluminum-Alloy Composition on the Structure, Composition, and Thermophysical Properties of Coatings Formed by Microarc Oxidation

    by N. Yu. Dudareva

    The effect of silicon contained in aluminum alloys on the structure, phase composition, and thermophysical properties of coatings formed by microarc oxidation has been demonstrated. The studies have been performed using samples made of AK12pch eutectic alloy with a silicon content of ~12% of Si and foreign-produced M244 hypereutectic alloy with a silicon content of ~26% of Si. Microarc oxidation coatings have been formed on all samples in a capacitive setup in a silicate-alkaline electrolyte using the same process conditions for all samples. The structure of the alloys and the resulting coatings has been analyzed. The coating thickness, porosity, microhardness, phase composition, and heat capacity have been determined. It has been found that silicon in the aluminum alloy contributes to an increase in the coating thickness, porosity, and heat capacity. Silicon in the alloy also contributes to an increase in the fraction of the amorphous phase in the coating and the amount of silicon oxide.

  • Influence of the Piston Crown Ceramic Coating on the Thermal State of Engine Parts and Heat Flows Distribution in the Combustion Chamber

    by N. Yu. Dudareva

    The influence of the coating formed on the piston crown using the microarc oxidation technology on the thermal state of engine parts and on the heat flows

  • The Effect of Silicon in an Aluminum Alloy on the Composition and Structure of Coatings Formed by Microarc Oxidation

    by N. Yu. Dudareva, V. M. Sitdikov

    The paper considers the effect of silicon in aluminum alloys on the structure, phase composition, and properties of coatings obtained by microarc oxidation. The research was carried out on samples made of eutectic aluminum alloy AK12ph (∼12% Si) and foreign hypereutectic aluminum alloy M244 (∼26% Si). The coatings were formed by microarc oxidation in a silicate-alkali electrolyte on a capacitive installation in the same technological mode for all samples. The thickness, porosity, phase composition, and crystallite sizes were determined for the formed coatings. Experimental dataset showed that silicon in an aluminum alloy contributes to the formation of coatings with greater thickness and high porosity. The coating thickness on the M244 alloy is ∼273 μm, which is 1.43 times greater than that of the coating on the AK12ph alloy. The macroporosity of the coatings on the M244 alloy is also high (∼29%), which is 4.8 times higher than that of the coating on the AK12ph alloy. The proportion of nanoscale pores with a diameter of less than 100 nm was determined from the high-magnification photograph of coating sections. The coating on the M244 alloy has a sufficiently high nanoscale porosity of 15.3%, which is 2.6 times higher than on the AK12ph alloy. X-ray phase analysis showed that silicon in an aluminum alloy increases the proportion of aluminosilicates (mullite and sillimanite) in the coating, the amounts of which in the coating on the M244 alloy reaches 76%, which is 1.3 times more than that of the coating on the AK12ph alloy. Aluminosilicate phases contribute to reducing the microhardness of the coatings. The results of this study demonstrate the possibility of controlling the structure and properties of coatings by changing the chemical composition of aluminum alloys subjected to microarc oxidation.

  • НАНОСТРУКТУРНОЕ ПОКРЫТИЕ ДЛЯ СНИЖЕНИЯ ТОКСИЧНОСТИ ДВИГАТЕЛЕЙ ВНУТРЕННЕГО СГОРАНИЯ

    by В.м. Ситдиков, Н.ю. Дударева

    Исследовано влияние наноструктурного покрытия, сформированного методом микродугового оксидирования на поршнях двигателей внутреннего сгорания на токсичность отработавших газов. Выявлена роль наноразмерной пористости в механизме снижения токсичности.

  • Effect of Microarc Oxidation Coating on the Corrosion Resistance of a Nanostructured Eutectic Aluminum Alloy

    by N. Yu. Dudareva, S. K. Kiseleva, L. I. Zainullina, M. M. Abramova, A. V. Kolomeichenko

    The effect of the structure and corrosion-protective properties of the coatings formed by microarc oxidation (MAO) on a eutectic aluminum alloy with an ultrafine-grained (UFG) structure or an initial structure is studied. The UFG structure is found to increase the corrosion rate of samples by 15.3 times. The coating increases the corrosion rate of the coarse-grained alloy by 2.5 times and does not affect the corrosion rate of the sample with an UFG structure.

  • Reducing the Toxicity of the Exhaust Gases from the Internal Combustion Engine by Using a Ceramic Coating on Components of the Combustion Chamber

    by N. Yu. Dudareva, V. M. Sitdikov

    —One of the most pressing problems in piston engine engineering is the toxicity of the exhaust gases from internal combustion engines. Recently, the possibilities of using catalytic converters directly in the engine combustion chamber have been considered. Such converters can be created by applying special coatings to the surfaces of components of the combustion chamber. The most promising method is microarc oxidation, which allows the formation of ceramic coatings with high adhesive strength on aluminum alloy parts. Many experimental studies have demonstrated that such coatings can reduce the amounts of some components of exhaust gases in the combustion chamber. Since theoretical justifications for the use of such coatings to reduce the toxicity of exhaust gases have not been developed, the purpose of this work was the theoretical justification, development, and verification of a mathematical model of neutralizing exhaust gas components by coating combustion chamber parts by the microarc oxidation method. The developed mathematical model of reducing the amount of individual exhaust gas components in the engine combustion chamber takes into account many factors: geometric parameters and performance characteristics of the engine, as well as coating properties and exhaust gas composition. Based on previously obtained experimental data on an RMZ-551i engine, the developed mathematical model was verified over a wide range of speeds (2000–6000 min–1) and throttle opening values (25–100%). Verification by CO showed that the mathematical model allows calculations to be carried out with a sufficiently high convergence, at the level of an order of magnitude, and that it can be used for a preliminary assessment of the influence of various factors on the amounts of toxic components in engine exhaust gases.

  • Corrosion resistance of ceramic coatings formed by microarc oxidation on aluminium alloy AK4-1

    by N. Yu. Dudareva, A. V. Kolomeichenko, V. B. Deev

    This paper describes a study that looked at the effect of the structure of coatings produced by microarc oxidation (MAO) on wrought aluminium alloy AK4-1 on the corrosion resistance of specimens. Different processing modes were applied that were determined by three factors: the capacity of the unit and the concentration of caustic potash and sodium metasilicate in the electrolyte. The coating thickness, coating porosity and corrosion rate of the specimens were used as output parameters. A complete factorial experiment of type 23 was designed and conducted. Images of microsections obtained with a scanning electron microscope were used for studying the coating structure, determined by its porosity and thickness. The porosity was analyzed based on images of the specimens with the help of ImageJ programme. For the corrosion resistance study, the specimens were immersed in a corrosive solution and their corrosion rate was determined. Regression and correlation analyses of the obtained data were carried out in the MS Excel programme. The correlation analysis showed that the corrosion rate strongly depends on the coating thickness. An increase in the coating thickness leads to an increase in the corrosion rate. It is assumed that the coating material does not corrode, and corrosion is the result of the aggressive solution penetrating through cracks to the substrate material, which is what basically corrodes. An increased thickness of the coating is associated with a greater number of cracks in it, which leads to an increased corrosion rate. It was also found that a greater capacity of the unit contributes to the coating thickness on the AK4-1 alloy. Regression equations were also obtained that relate the corrosion rate to the porosity and thickness of the coating, as well as the corrosion rate, porosity and thickness of the coating to the microarc oxidation modes.Support for this research was provided by the Ministry of Science and Higher Education of the Russian Federation under Governmental Assignment No. FEUE-2023-0007 (UUST).

  • Open Access

    The efficiency of thermal protection of ICE pistons with the micro-arc oxidation

    by Natalia Yu. Dudareva, Alexander V. Kolomeichenko, Yury E. Kisel, Коломейченко Александр Викторович

    BACKGROUND: In order to protect pistons of internal combustion engines (ICE) from burnout and increase their durability, it is reasonable to use ceramic coatings formed on the piston head with micro-arc oxidation (MAO). Many scientific papers have been devoted to the study of the efficiency of these coatings. However, most of these studies were carried out at laboratory facilities simulating the engine operation, generally, not taking into account the real thermophysical parameters of the MAO coating. Therefore, the thermal protection efficiency of these coatings is difficult to assess. AIM: Study of efficiency of the thermal protection of pistons using a ceramic coating formed by micro-arc oxidation on the piston head with numerical simulation. METHODS: The study was conducted in the SolidWorks Simulation software. Two piston aluminum alloys were used as the piston material: AK12d (with a silicon content of 12%) and AK4-1 (with a silicon content of 0.35%). Temperature loads corresponding to the operation of a real engine were applied to the surfaces of the model piston. At the first stage of the study, the thermal state of pistons made of different uncoated alloys was simulated. At the second and third stages of the study, the effect of the coating thickness on the piston thermal state was simulated. The piston material of the second study stage was the AK4-1 alloy. The piston material of the third study stage was the AK12d alloy. Ceramics, which properties correspond to the coatings properties formed with the micro-arc oxidation method on these alloys, were used as the coating material. The coating thickness varied in the range from 50 to 350 µm in increments of 100 µm. The probing method was used to determine the temperature in various areas of the piston, such as at the piston head surface at the MAO coating and under it, in the area of piston grooves, at a piston skirt and the piston head from the side of a crankcase. RESULTS: With the simulation, it was found that: The micro-arc coating of the piston head reduces the thermal tension of the piston regardless of the aluminum alloy chemical composition. The efficiency of the piston’s thermal protection increases with an increase in the ceramic coating thickness and a decrease in its thermal conductivity coefficient. The greatest heat-protecting effect is achieved by the piston made of the AK12d eutectic alloy. CONCLUSIONS: It is found that the MAO coating at the piston head is an effective way to reduce the thermal tension of the ICE pistons. Increasing the ceramic coating thickness and a decrease in its thermal conductivity coefficient increases the efficiency of the pistons thermal protection. Reducing the thermal conductivity of the MAO coating and increasing the MAO coating thickness increases the temperature on the coating surface.

  • Effect of microarc oxide coating on corrosion resistance of nanostructured eutectic aluminum alloy

    by Ufa University of Science and Technology, N.YU. Dudareva, S.K. Kiseleva, L.I. Zaynullina, M.M. Abramova, A.V. Kolomeychenko, Central Scientific Research Automobile and Automotive Engines Institute «NAMI»

    Исследовано влияние структуры и коррозионно-защитных свойств покрытий, сформированных методом микродугового оксидирования (МДО) на эвтектическом алюминиевом сплаве с ультрамелкозернистой структурой (УМЗ), а также с исходной структурой. Установлено, что УМЗ-структура увеличивает скорость коррозии образцов в 15,3 раза. Покрытие увеличивает скорость коррозии на образце из крупнозернистого сплава в 2,5 раза и не влияет на скорость коррозии на образце с УМЗ-структурой.

  • Effect of mao ceramic coating on the stress-strain state of internal combustion engine pistons

    by N. Yu. Dudareva, A. V. Kolomeychenko, V. B. Deev

    The authors of this paper used numerical modelling technique to look at the effect of ceramic coating formed on the surface of internal combustion engine piston crown on the level of stresses and strains in the piston material. The modelling was performed in SolidWorks Simulation. The following materials were used: for piston – hypereutectic aluminium piston alloy, for coating – ceramics. The properties of such ceramics were similar to the ones of micro-arc oxidation coatings. The surfaces of the model piston were subjected to mechanical and thermal loads corresponding to the ones experienced by the model engine. The effect of the coating thickness on the stress-strain state of the studied part was examined. The coating thickness was varied at 50 μm increments in the range of 50 to 300 μm. The modelling showed that the coating helped to significantly lower the level of stresses and strains in the most loaded points located in the centre of the piston crown. Thus, due to the coating the stress is decreased 8.6 times and the equivalent strain — 15.8 times. In the point located in the centre of the piston crown surface on the crankcase side, the stress is decreased 5.3 times and the strain — 6.1 times. Less distinguished changes were noted on the edge of the piston crown surface: due to the coating the stress there is 1.1 times lower and the strain — 1.6 times lower. This study helped understand that the coating thickness produces no considerable effect on the strains or stresses in the piston material. A 50 μm thick coating is sufficient to achieve the required effect.This research was carried out as part of Governmental Assignment No. FEUE-2023-0007 (Ufa University of Science and Technology), with the funding provided by the Ministry of Science and Higher Education of the Russian Federation.