Bhargab Madhab Barua
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bhargab Madhab Barua has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Maneswar Rahang
National Institute of Technology Meghalaya
2 shared publications Dhinakaran Veeman
Chennai Institute of Technology
1 shared publicationManeswar Rahang
Department of Mechanical Engineering, National Institute of Technology, Meghalaya
1 shared publication- Rashed Mustafa Mazarbhuiya
Centre for Additive Manufacturing, Chennai Institute of Technology, Chennai 600069, Tamil Nadu, India
1 shared publication
Latest Publications
- 12 February 2026
- Published by SAGE Publications in Surface Engineering
- Vol. 42 (3) , 297-307
Tungsten-copper coating development on superalloy substrates using Taguchi method
The current study investigated the deposition behaviour of the tool particles made from powder metallurgical (PM) green compact tool of W-Cu for coatings on Inconel 800 superalloy substrate using the electric discharge alloying (EDA) process. The effect of process variables such as compact load (CL), voltage (V) and duty factor (DF) is systematically analysed over the output responses, i.e., material deposition rate (MDR), tool wear rate (TWR) and surface roughness (Ra). The results indicated a maximum TWR of 225.325 mg/min, a maximum MDR of 47.250 mg/min and a minimum Ra of 3.5 µm. The alloyed layer is further characterized by FESEM analysis. The weight and atomic percentage of the migrated particles are determined by EDS analysis. The elemental mapping further confirmed the enrichment of tool particles and other base material constituents within the alloyed surface. The XRD analysis further showed the existence of tool elements and the development of new compounds in the alloyed layer. The alloyed layer exhibited an average layer thickness of 11.354 µm.
- 12 February 2026
- Published by SAGE Publications in Surface Engineering
- Vol. 42 (3) , 297-307
Tungsten-copper coating development on superalloy substrates using Taguchi method
The current study investigated the deposition behaviour of the tool particles made from powder metallurgical (PM) green compact tool of W-Cu for coatings on Inconel 800 superalloy substrate using the electric discharge alloying (EDA) process. The effect of process variables such as compact load (CL), voltage (V) and duty factor (DF) is systematically analysed over the output responses, i.e., material deposition rate (MDR), tool wear rate (TWR) and surface roughness (Ra). The results indicated a maximum TWR of 225.325 mg/min, a maximum MDR of 47.250 mg/min and a minimum Ra of 3.5 µm. The alloyed layer is further characterized by FESEM analysis. The weight and atomic percentage of the migrated particles are determined by EDS analysis. The elemental mapping further confirmed the enrichment of tool particles and other base material constituents within the alloyed surface. The XRD analysis further showed the existence of tool elements and the development of new compounds in the alloyed layer. The alloyed layer exhibited an average layer thickness of 11.354 µm.
- 24 March 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (20) , 23503-23517
Experimental Investigation on the Integrity of Surfaces Prepared using Copper/Multi-walled Carbon Nanotube Green Compact Tool in Electric Discharge Coating Process
- 24 March 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (20) , 23503-23517
Experimental Investigation on the Integrity of Surfaces Prepared using Copper/Multi-walled Carbon Nanotube Green Compact Tool in Electric Discharge Coating Process
- 4 March 2022
- Published by SAGE Publications in Surface Engineering
- Vol. 38 (3) , 261-270
Surface modification of Al-7075 using Cu-CNT green tool in EDM
Now-a-days carbon nanotube (CNT) is widely used because of its inimitable properties such as high electrical and thermal conductivities, high tensile strength, etc. In this work, an attempt has been made to modify the surface of Al-7075 alloy using Cu-MWCNT powder metallurgy green compact tool in the electric discharge machining process. The effects of contributing parameters i.e. peak current (Ip), voltage and compact load (CL) have been investigated with respect to performance measures such as, Material Deposition Rate (MDR), Tool Wear Rate (TWR) and Surface Roughness (Ra). The modified surface has been assessed by optical microscopy, FESEM, XRD and EDS analyses. Highest MDR of 0.15 mg min–1, lowest TWR of 2.05 mg min–1 and lowest Ra of 2.57 µm have been attained. The deposition of tool materials has improved the microhardness up to 2.6 times than that of base material.
- 4 March 2022
- Published by SAGE Publications in Surface Engineering
- Vol. 38 (3) , 261-270
Surface modification of Al-7075 using Cu-CNT green tool in EDM
Now-a-days carbon nanotube (CNT) is widely used because of its inimitable properties such as high electrical and thermal conductivities, high tensile strength, etc. In this work, an attempt has been made to modify the surface of Al-7075 alloy using Cu-MWCNT powder metallurgy green compact tool in the electric discharge machining process. The effects of contributing parameters i.e. peak current (Ip), voltage and compact load (CL) have been investigated with respect to performance measures such as, Material Deposition Rate (MDR), Tool Wear Rate (TWR) and Surface Roughness (Ra). The modified surface has been assessed by optical microscopy, FESEM, XRD and EDS analyses. Highest MDR of 0.15 mg min–1, lowest TWR of 2.05 mg min–1 and lowest Ra of 2.57 µm have been attained. The deposition of tool materials has improved the microhardness up to 2.6 times than that of base material.