Adnan Hosen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Adnan Hosen has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Sheikh Rashel Al Ahmed
4 shared publications- Sheikh Rashel Al Ahmed
Department of Electrical, Electronic and Communication Engineering, Pabna University of Science and Technology, Pabna 6600, Bangladesh
4 shared publications K.M. Sayem Bin Rahmotullah
2 shared publicationsBenjer Islam
Pabna University of Science and Technology,Department of Electrical, Electronic, and Communication Engineering,Pabna 6600,Bangladesh
1 shared publicationFerdous Rahman
1 shared publicationHabiba Khatun
Pabna University of Science and Technology,Department of Electrical, Electronic, and Communication Engineering,Pabna 6600,Bangladesh
1 shared publication
Latest Publications
- 16 September 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Design and simulation of a highly efficient CuBi2O4 thin-film solar cell with hole transport layer
- 16 September 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Design and simulation of a highly efficient CuBi2O4 thin-film solar cell with hole transport layer
- 2 January 2023
- Published by Wiley in Advanced Theory and Simulations
- Vol. 6 (2)
Improving the Performance of Lead‐Free FASnI3‐Based Perovskite Solar Cell with Nb2O5 as an Electron Transport Layer
In this work, the photovoltaic outputs of the lead‐free FASnI3‐based perovskite solar cells are discussed by using Solar Cell Capacitance Simulator in One Dimension. The device outputs estimated theoretically in this study are almost equal to the experimental results, thereby verifying accuracy of this simulation. To find the decent electron transport layer (ETL), herein, various ETLs are presented instead of C60/BCP in the experimental FASnI3‐based perovskite solar cell (PSC). The designed FASnI3 PSC utilizing niobium pentoxide (Nb2O5) as an ETL with an appropriate band alignment and a low lattice mismatch at FASnI3/ETL interface provides better efficiency by decreasing recombination at front side. The performances of the proposed PSC are also measured by altering the thickness and doping of ETL and absorber, interface defects, and series and shunt resistances. Furthermore, this paper reports the calculation of recombination coefficients at absorber/ETL interface, depletion region, and quasi‐neutral region. An improved efficiency of 22.24% is evaluated at optimized thicknesses of 100 nm for HTL, 500 nm for absorber, 50 nm for ETL, and 50 nm for ITO for the proposed inverted PSC of ITO/PEDOT:PSS/FASnI3/Nb2O5/Ag. These results suggest that chemically stable and less‐toxic Nb2O5 can be applied as a useful ETL in inverted PSCs for further improving the performances.
- 2 January 2023
- Published by Wiley in Advanced Theory and Simulations
- Vol. 6 (2)
Improving the Performance of Lead‐Free FASnI3‐Based Perovskite Solar Cell with Nb2O5 as an Electron Transport Layer
In this work, the photovoltaic outputs of the lead‐free FASnI3‐based perovskite solar cells are discussed by using Solar Cell Capacitance Simulator in One Dimension. The device outputs estimated theoretically in this study are almost equal to the experimental results, thereby verifying accuracy of this simulation. To find the decent electron transport layer (ETL), herein, various ETLs are presented instead of C60/BCP in the experimental FASnI3‐based perovskite solar cell (PSC). The designed FASnI3 PSC utilizing niobium pentoxide (Nb2O5) as an ETL with an appropriate band alignment and a low lattice mismatch at FASnI3/ETL interface provides better efficiency by decreasing recombination at front side. The performances of the proposed PSC are also measured by altering the thickness and doping of ETL and absorber, interface defects, and series and shunt resistances. Furthermore, this paper reports the calculation of recombination coefficients at absorber/ETL interface, depletion region, and quasi‐neutral region. An improved efficiency of 22.24% is evaluated at optimized thicknesses of 100 nm for HTL, 500 nm for absorber, 50 nm for ETL, and 50 nm for ITO for the proposed inverted PSC of ITO/PEDOT:PSS/FASnI3/Nb2O5/Ag. These results suggest that chemically stable and less‐toxic Nb2O5 can be applied as a useful ETL in inverted PSCs for further improving the performances.
- Open Access
- 17 May 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 19 (1) , 41
Impact of Hole Transport Layers in Inorganic Lead-Free B-γ-CsSnI3 Perovskite Solar Cells: A Numerical Analysis
Tin-based halide perovskite compounds have attracted enormous interest as effective replacements for the conventional lead halide perovskite solar cells (PCSs). However, achieving high efficiency for tin-based perovskite solar cells is still challenging. Herein, we introduced copper sulfide (CuS) as a hole transport material (HTM) in lead free tin-based B-γ-CsSnI3 PSCs to enhance the photovoltaic (PV) performances. The lead free tin-based CsSnI3 perovskite solar cell structure consisting of CuS/CsSnI3/TiO2/ITO was modeled and the output characteristics were investigated by using the one dimensional solar cell capacitance simulator (SCAPS-1D). The CuS hole transport layer (HTL) with proper band arrangement may notably minimize the recombination of the charge carrier at the back side of the perovskite absorber. Density functional theory (DFT)-extracted physical parameters including the band gap and absorption spectrum of CuS were used in the SCAPS-1D program to analyze the characteristics of the proposed PV device. The PV performance parameters of the proposed device were numerically evaluated by varying the absorber thickness and doping concentration. In this work, the variation of the functional temperature on the cell outputs was also studied. Furthermore, different HTMs were employed to investigate the PV characteristics of the proposed CsSnI3 PSC. The power conversion efficiency (PCE) of ~29% was achieved with open circuit voltage (Voc) of 0.99 V, a fill factor of ~87%, and short circuit current density (Jsc) of 33.5 mA/cm2 for the optimized device. This work addressed guidelines and introduced a convenient approach to design and fabricate highly efficient, inexpensive, and stable lead free tin-based perovskite solar cells.
- 17 May 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 19 (1) , 41
Open AccessImpact of Hole Transport Layers in Inorganic Lead-Free B-γ-CsSnI3 Perovskite Solar Cells: A Numerical Analysis
Tin-based halide perovskite compounds have attracted enormous interest as effective replacements for the conventional lead halide perovskite solar cells (PCSs). However, achieving high efficiency for tin-based perovskite solar cells is still challenging. Herein, we introduced copper sulfide (CuS) as a hole transport material (HTM) in lead free tin-based B-γ-CsSnI3 PSCs to enhance the photovoltaic (PV) performances. The lead free tin-based CsSnI3 perovskite solar cell structure consisting of CuS/CsSnI3/TiO2/ITO was modeled and the output characteristics were investigated by using the one dimensional solar cell capacitance simulator (SCAPS-1D). The CuS hole transport layer (HTL) with proper band arrangement may notably minimize the recombination of the charge carrier at the back side of the perovskite absorber. Density functional theory (DFT)-extracted physical parameters including the band gap and absorption spectrum of CuS were used in the SCAPS-1D program to analyze the characteristics of the proposed PV device. The PV performance parameters of the proposed device were numerically evaluated by varying the absorber thickness and doping concentration. In this work, the variation of the functional temperature on the cell outputs was also studied. Furthermore, different HTMs were employed to investigate the PV characteristics of the proposed CsSnI3 PSC. The power conversion efficiency (PCE) of ~29% was achieved with open circuit voltage (Voc) of 0.99 V, a fill factor of ~87%, and short circuit current density (Jsc) of 33.5 mA/cm2 for the optimized device. This work addressed guidelines and introduced a convenient approach to design and fabricate highly efficient, inexpensive, and stable lead free tin-based perovskite solar cells.
- 22 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Enhanching memory performance in silicon nitride-based charge trapping memory device with Al2O3 blocking oxide and TiO2 capping layers
In this paper, we propose a novel charge trapping memory (CTM) device structure consisting of Si/TiO 2 /Al 2 O 3 /Si 3 N 4 /SiO 2 /Si (STANOS), where Al 2 O 3 as blocking oxide and TiO 2 as capping layers have been employed. The SILVACO Technology Computer-Aided Design (TCAD) simulation software is used to model and study the performance of the proposed CTM device. A comparative investigation of the memory performances amid the conventional silicon-oxide-nitride-oxide-silicon (SONOS) and the proposed STANOS is provided. It is found that the STANOS structure with Al 2 O 3 blocking oxide and TiO 2 capping layers shows faster programming and erasing speeds than the conventional SONOS structure. Al 2 O 3 having higher barrier height impacts on better blocking efficiency with enhancing programming speed and TiO 2 capping layer with modest dielectric constant suppresses electron injection during erasing operation. In addition, blocking layer with capping minimizes the electron emission during charge retention. These results will be useful to develop low-cost and low power consumption nitride-based CTM devices with better programming and erasing speeds.
- 22 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Enhanching memory performance in silicon nitride-based charge trapping memory device with Al2O3 blocking oxide and TiO2 capping layers
In this paper, we propose a novel charge trapping memory (CTM) device structure consisting of Si/TiO 2 /Al 2 O 3 /Si 3 N 4 /SiO 2 /Si (STANOS), where Al 2 O 3 as blocking oxide and TiO 2 as capping layers have been employed. The SILVACO Technology Computer-Aided Design (TCAD) simulation software is used to model and study the performance of the proposed CTM device. A comparative investigation of the memory performances amid the conventional silicon-oxide-nitride-oxide-silicon (SONOS) and the proposed STANOS is provided. It is found that the STANOS structure with Al 2 O 3 blocking oxide and TiO 2 capping layers shows faster programming and erasing speeds than the conventional SONOS structure. Al 2 O 3 having higher barrier height impacts on better blocking efficiency with enhancing programming speed and TiO 2 capping layer with modest dielectric constant suppresses electron injection during erasing operation. In addition, blocking layer with capping minimizes the electron emission during charge retention. These results will be useful to develop low-cost and low power consumption nitride-based CTM devices with better programming and erasing speeds.
- 22 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Device simulation of a highly efficient CZTS solar cell with CuS as hole transport layer
Earth abundant and economical chalcogenide Cu 2 ZnSnS 4 (CZTS) is an encouraging active material for kesterite thin-film solar cell (TFSC) applications. However, the CZTS solar cell has drawback in performances compared to CIGS photovoltaic (PV) device due to insufficient current density and improper design. In the present work, the Solar Cell Capacitance Simulator in One Dimension (SCAPS-1D) is used to model a novel heterojunction CZTS solar cell and the PV performance parameters are also evaluated numerically. Herein, we have proposed the CuS material as a hole transport layer (HTL) at the back of CZTS absorber layer, the CdS as buffer layer, and the ITO as window layer, respectively. The simulation work is performed by investigating the effects of absorber thickness, carrier concentration, and defects on cell performances. The effect of temperature on device performances is also studied. With the heterojunction structure consisting of CuS/CZTS/CdS/ITO, the best conversion efficiency of 26.53% is achieved with open circuit voltage of 1.10 V, fill-factor of 87.28%, and short-circuit current density of 27.74 mA/cm 2 . The overall simulated results reveal that the CuS can be utilized as a prominent HTL to obtain the high efficiency in the CZTS TFSC with low-cost and reliable fabrication.
- 22 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Device simulation of a highly efficient CZTS solar cell with CuS as hole transport layer
Earth abundant and economical chalcogenide Cu 2 ZnSnS 4 (CZTS) is an encouraging active material for kesterite thin-film solar cell (TFSC) applications. However, the CZTS solar cell has drawback in performances compared to CIGS photovoltaic (PV) device due to insufficient current density and improper design. In the present work, the Solar Cell Capacitance Simulator in One Dimension (SCAPS-1D) is used to model a novel heterojunction CZTS solar cell and the PV performance parameters are also evaluated numerically. Herein, we have proposed the CuS material as a hole transport layer (HTL) at the back of CZTS absorber layer, the CdS as buffer layer, and the ITO as window layer, respectively. The simulation work is performed by investigating the effects of absorber thickness, carrier concentration, and defects on cell performances. The effect of temperature on device performances is also studied. With the heterojunction structure consisting of CuS/CZTS/CdS/ITO, the best conversion efficiency of 26.53% is achieved with open circuit voltage of 1.10 V, fill-factor of 87.28%, and short-circuit current density of 27.74 mA/cm 2 . The overall simulated results reveal that the CuS can be utilized as a prominent HTL to obtain the high efficiency in the CZTS TFSC with low-cost and reliable fabrication.
- Open Access
- 9 April 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (5) , 1-13
Simulating the performance of a highly efficient CuBi2O4-based thin-film solar cell
In this study, copper bismuth oxide (CuBi2O4) absorber-based thin film heterojunction solar cell structure consisting of Al/FTO/CdS/CuBi2O4/Ni has been proposed. The proposed solar cell device structure has been modeled and analyzed by using the solar cell capacitance simulator in one dimension (SCAPS-1D) software program. The performance of the proposed photovoltaic device is evaluated numerically by varying thickness, doping concentrations, defect density, operating temperature, back metal contact work function, series and shunt resistances. The current density–voltage behaviors at dark and under illumination are investigated. To realize the high efficiency CuBi2O4-based solar cell, the thickness, acceptor and donor densities, defect densities of different layers have been optimized. The present work reveals that the power conversion efficiency can be enhanced by increasing the absorber layer thickness. The efficiency of 26.0% with open-circuit voltage of 0.97 V, short-circuit current density of 31.61 mA/cm2, and fill-factor of 84.58% is achieved for the proposed solar cell at the optimum 2.0-μm-thick CuBi2O4 absorber layer. It is suggested that the p-type CuBi2O4 material proposed in the present study can be employed as a promising absorber layer for applications in the low cost and high efficiency thin-film solar cells.
- 9 April 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (5) , 1-13
Open AccessSimulating the performance of a highly efficient CuBi2O4-based thin-film solar cell
In this study, copper bismuth oxide (CuBi2O4) absorber-based thin film heterojunction solar cell structure consisting of Al/FTO/CdS/CuBi2O4/Ni has been proposed. The proposed solar cell device structure has been modeled and analyzed by using the solar cell capacitance simulator in one dimension (SCAPS-1D) software program. The performance of the proposed photovoltaic device is evaluated numerically by varying thickness, doping concentrations, defect density, operating temperature, back metal contact work function, series and shunt resistances. The current density–voltage behaviors at dark and under illumination are investigated. To realize the high efficiency CuBi2O4-based solar cell, the thickness, acceptor and donor densities, defect densities of different layers have been optimized. The present work reveals that the power conversion efficiency can be enhanced by increasing the absorber layer thickness. The efficiency of 26.0% with open-circuit voltage of 0.97 V, short-circuit current density of 31.61 mA/cm2, and fill-factor of 84.58% is achieved for the proposed solar cell at the optimum 2.0-μm-thick CuBi2O4 absorber layer. It is suggested that the p-type CuBi2O4 material proposed in the present study can be employed as a promising absorber layer for applications in the low cost and high efficiency thin-film solar cells.