HAHafiz Ali̇soy

Hafiz Ali̇soy

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hafiz Ali̇soy has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Electromagnetic and Thermal Analysis of Power Losses in Metal Sheaths of Unarmored and Armored Power Cables

    by Hafiz Alisoy, Hakan Çanta, Tufan Alpözgen

    In this study, active power losses occurring in the metallic sheaths of single-core unarmored and armored power cables utilized in high-voltage power transmission and distribution systems are rigorously investigated via analytical and electromagnetic approaches. Under alternating current (AC) operating conditions, the underlying physical mechanisms generating induced eddy and circulating currents on the sheath surface are mathematically derived based on Maxwell's equations and Faraday's Law of Induction. Skin and proximity effects, which introduce asymmetry into the current density distribution across the conductor cross-section, are explicitly modeled in compliance with the international standard IEC 60287. To quantitatively evaluate the impact of these theoretical formulations on practical engineering systems, a comprehensive full-step analytical scenario is established for a single-core 1×240 mm² XLPE-insulated steel-sheathed cable line under a solid-bonded configuration at both ends. The restrictive effects of the induced sheath losses on the cable's thermal budget and core ampacity are explicitly quantified and discussed

  • Kablo Mühendisliğinin Fiziksel Temellerine Giriş

    by Hafız ALİSOY, Hakan Çanta, Tufan Alpözgen

    Kablo mühendisliği, modern enerji iletim ve dağıtım şebekelerinin temel taşı olmasına rağmen, teorik temelleri ile endüstriyel uygulamaları arasındaki dengeyi kuran kapsamlı Türkçe kaynak ihtiyacı her geçen gün artmaktadır. "Kablo Mühendisliğinin Fiziksel Temellerine Giriş" başlığını taşıyan bu kitap “Namık Kemal Üniversitesi Çorlu Mühendislik Fakültesi Elektrik Elektronik Mühendisliği Bölümü ile Ünika Üniversal Kablo Sanayi ve Ticaret Anonim Şirketi arasında oluşturulan Üniversite-Sanayi İş birliği” kapsamında, bu boşluğu doldurmak amacıyla, iletken damarların tasarımından karmaşık termal hesaplamalara kadar geniş bir perspektifi akademik bir disiplinle sunmaktadır. Eserin temel odağı, iletken damarların geometrik tasarımı ve özellikle enerji yoğunluğu açısından kritik öneme sahip kablo özünün matematiksel ve fiziksel hesaplama yöntemlerini detaylandırmaktır. Kitap boyunca AC ve DC güç kablolarının çalışma prensipleri, elektromanyetik alan teorisi ışığında analiz edilmiş; iletim hatlarındaki elektriksel karakteristikler modern mühendislik yaklaşımlarıyla ele alınmıştır. Bir kablo sisteminin güvenilirliği ve ömrü, büyük ölçüde onun termal kararlılığına bağlıdır. Bu bağlamda kitapta; Ekran ve yalıtım tabakalarında meydana gelen dielektrik ve omik güç kayıpları, Toprak altına ve havaya döşenmiş kabloların ısı transfer mekanizmaları, Farklı ortam koşullarında değişkenlik gösteren termal direnç hesaplamaları, titizlikle incelenmiş ve mühendislik tasarım süreçlerine entegre edilecek formülasyonlarla sunulmuştur. Ayrıca, uluslararası standartlara uygun işaretlemeler ve çeşitli kablo tasarımlarının yapısal özellikleri, okuyucunun pratik sahada ihtiyaç duyacağı teknik verilerle desteklenmiştir.

  • Tunneling Conductivity of Disordered Dielectrics

    by Hafiz Alisoy, Arif Kivanc Ustun, Lütfi Ulusoy, Meltem Apaydın Üstün, Hakan Çanta

    Disordered dielectric materials, such as polymers, exhibit charge transport dominated by electron localization due to their structural inhomogeneity. Traditional percolation theory has been widely used to describe conductivity in these systems; however, it often overlooks the quantum mechanical processes at play. This study presents a tunneling conductivity model grounded in quantum principles, linking microscopic electron transfer between localized states to the observed macroscopic electrical behavior. The approach addresses longstanding discrepancies in doped semiconductor systems by accurately capturing the reduction in characteristic tunneling parameters at short inter-center distances, thus aligning theoretical predictions with experimental results. Experimental validation is achieved through oxygen ion implantation in polyethylene (PE) and polyvinylcarbazole (PVC), where the introduction of defects is shown to directly enhance tunneling-driven conductivity. Additional pressure-dependent measurements reveal a logarithmic relationship between resistance and the square root of applied pressure, supporting the model’s description of strain-modulated tunneling pathways. Comparative analysis with amorphous semiconductors and low-molecular-weight dielectrics further demonstrates the model’s broad applicability across various disordered systems. By moving beyond phenomenological descriptions, this work provides a quantum mechanical framework for understanding and predicting conductivity in disordered dielectrics, offering valuable insights for the design of advanced polymer-based insulating materials.

  • Evaluation of the Electric Field of a Single-Core Power Cable at the Inner Conductor Radius

    by Hafiz Alisoy, Reşat Mutlu, Rabia Korkmaz Tan, Hakan Çanta

    Dielectric strength is a very important parameter for cables. It can vary according to temperature and frequency. The complex electrical permittivity of the Cross-linked polyethylene (XLPE) and Copper Polyester/Mylar band layers of a cable determine the maximum electric field created inside the cable operating at sinusoidal voltage. The value of this electric field should be less than the dielectric strength of the materials used. The electrical characteristics of XLPE and Copper Polyester tape depend on frequency and temperature. In a power cable, the temperature depends on the radial position, which makes it difficult to calculate the cable’s electric field. In this study, it was shown how to calculate the electric field of the cable by using XLPE and Copper Polyester band data taken from the literature and numerical integration. It was found that the calculated value is less than the Dielectric strength value of XLPE material. It has been shown how the electric field of the power cable under investigation changes according to frequency and temperature.


  • The Frequency Response of the Butterworth Filter Approximation

    by Hafiz Ali̇sOy, Hasan Demi̇r, Shahriyar Ahmedov1

    This study creates the design of a 10th order Butterworth bandpass filter based on an operational amplifier. It also provides the analysis of the results obtained in this context. Higher order filters are constructed using a combination of second and third order filters. Four parameters need to be specified in order to design a Butterworth bandpass filter, namely Ap (passband attenuation in dB), As (stopband attenuation in dB), fp (frequency at which Ap occurs), and fs (frequency at which As occurs). The design procedure involves two steps: one is to find the required filter order, and the other is to find the scaling factor which is to be applied to the formatted parameter values. The Butterworth bandpass filter is a combination of a low-pass filter and a high-pass filter. For a Butterworth low-pass filter, the resistance is approximately of 100 kΩ and the capacitor value is found by inverse scaling with the frequency and the chosen resistance value. For a Butterworth high pass filter, the used capacitor value is approximately of 0.05 µF and the resistor value is found by inverse scaling with the frequency and the chosen resistance value.

  • Open Access

    Analysis of the Formation of Material Structures with Axial Symmetry by Strong Electric Field

    by Gülizar Alisoy, Hasan Demir, Hafiz Alisoy

    To solve various technical problems, technologies are needed that allow creating new types of functionally graded anisotropic composite materials with directional properties. The formation of such structures based on additive technologies continues to retain its relevance every day. In this context, this paper proposes a new approach to creating a structure with axial symmetry and electrical or mechanical properties. In this case, the possibility of controlling the movement and direction of particles using strong electric fields is used. Taking into account the presence of a strong electric field in a condensed medium located in the interelectrode space, a mathematical model for the formation of a structure with axial symmetry is proposed, based on the analysis of the forces acting on the particles in the medium. For this model, as a result of some simplifications, analytical solutions were found. According to the results obtained, it is believed that a strong electric field also allows forming certain structures of materials and products with certain properties from microparticles, similar to polymer chemistry.

  • Open Access

    Dynamics of Charging of Dielectric Liquid Drops in a Corona Discharge Field

    by Hafiz Alisoy, Hasan Demir, Gülizar Alisoy

    The development of innovative electrojet technologies based on the formation of sequential flows of monodisperse droplets in the working environment remains among the current problems today. In this study, it has been determined that in the “needle-plane” electrode system where corona discharge occurs. The charging kinetics of spherical particles are investigated in this system. These particles were created under equal conditions for various dielectric liquids. The spherical particles had different radii and different relative dielectric permittivities. The study determined that the charging kinetics of these particles differ. This difference depends on the polarity of the small radius electrode. In particular, the effective ionization coefficient in an electronegative gas environment (e.g. in air) where corona discharge occurs, it has been shown that when the needle electrode has a negative polarity, the amount of charge accumulated on the spherical particle is higher compared to the positive polarity case.

  • Open Access

    The Role Of Air Flow Optimization For Battery Life And Performance In Cordless Stick Vacuum Cleaners

    by Onur Hamdi Uzun, İzen Elmaslı, Mohammadreza Masoumisoureh, Mahir Yaşar, Selcen Çalışkan, Gizem Büşra Gök, Hafız Alisoy

    As technology develops, so does the demand for products that make our lives easier. Cordless stick vacuum cleaners are one of these products and have become increasingly popular in recent years particularly for the convenience of being cordless. However, there are many factors affecting battery life and vacuum performance of cordless stick cleaners, the most important of these factors is the heating of the battery. One solution to this problem is a design that aims to reduce the battery temperature and increase the vacuum performance of the cleaner by directing some of the outlet air from the motor to the battery pack. Tests were carried out with the air flow path closed and the air flow path open. As a result of the tests, it was observed that the battery performance and usage performance increased by approximately 30% when the air flow path was open.

  • Open Access

    Silindir-Düzlem Korona Elektrot Sisteminin Koşulsuz Optimizasyonu

    by Gülizar Ali̇soy, Necati Özbey, Lütfi Ulusoy, Hafiz Ali̇soy

    In this study, based on the Newton-Raphson method, the unconditional optimization of the “thin cylinder-plane” corona electrode system of high-voltage devices with a non-uniform or weakly uniform electric field, widely used in various technological processes of electron-ion technology, is analyzed. For this purpose, the condition of a self-sustaining electric discharge was used for the electrode system under consideration.

  • Open Access

    A Variational Problem for the Power Factor in Capacitance Charging Process

    by Hafiz Ali̇soy, Gülizar Ali̇soy, Mahir Yasar, Selcen Akinci, Gizem Büşra Gök, Mohammadreza Masoumi̇soureh

    In this study, the solution of a variational problem that allows determining the input voltage form that provides the maximum power factor of the battery charging process in the RLC circuit and the change character of the charging current for constant R, L, C and charging time has been examined. The defined problem is obtained and solved in the form of a linear integro-differential equation. A quadratic voltage criterion is proposed to analyze the convergence of the power factor to its maximum value for various modes of charging the battery.