YSYanhui Sun

Yanhui Sun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yanhui Sun has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simulation of Solidification Structure in the Vacuum Arc Remelting Process of Titanium Alloy TC4 Based on 3D CAFE Method

    by Zhenquan Jing, Rui Liu, Naitao Geng, Ying Wang, Yanhui Sun

    Vacuum arc remelting is the main production method of titanium alloy ingots at present. In order to obtain good quality ingots, it is of great significance to study the formation of the solidification structure of ingots via vacuum arc remelting. In order to select and optimize the nucleation parameters for the solidification microstructure simulation of an ingot, a 3D CAFE model for microstructure evolution during vacuum arc remelting was established, taking into account heat transfer, flow, and solute diffusion. The Gaussian distribution continuous nucleation model and extended KGT model were used to describe the grain nucleation and dendrite tip growth rates, respectively. The multi-point mass source and moving boundary method were used to simulate the ingot growth. The results show that there are three typical crystal regions in the solidification structure of vacuum arc remelting titanium alloy ingots, namely the surface fine crystal region, columnar crystal region, and central equiaxed crystal region. The proportion of the columnar crystal region in the solidification structure of an ingot increases gradually with the increase in the undercooling of the maximum bulk nucleation. With an increase in the maximum bulk nucleation density, the equiaxed grain zone gradually increases, and the grain size gradually decreases. The proportion of the columnar crystal region in the solidification structure of an ingot increases gradually with an increase in the undercooling of the maximum bulk nucleation. The maximum volume nucleation variance has no obvious effect on the change in the solidification structure. When the maximum volume nucleation undercooling is 5.5 K, the maximum volume nucleation standard deviation is 4 K, and the maximum volume nucleation density is 5 × 108. The solidification structure simulation results are in good agreement with the experimental results.


  • Open Access

    Numerical Simulation of Electromagnetic Field in Slab Electroslag Remelting Process with Double Electrode Series

    by Qi Li, Zhenquan Jing, Yanhui Sun

    In this paper, a mathematical model of an electromagnetic field during an electroslag remelting process of industrial-scale slab was established using a Maxwell 3D module in Ansys Electromagnetics Suite. The distribution characteristics of the magnetic field intensity, current density and Joule heat density during the electroslag remelting process were analyzed in detail. On this basis, the influence of the current frequency on the electroslag remelting process of an industrial scale is studied, and the influence of process parameters such as the slag pool depth, electrode insertion depth and ingot height on the electromagnetic field is also considered. The results show that the Joule heat generated in the slag pool is much greater than that of the electrode and the ingot. The maximum Joule heat is located at the contact between the electrode corner and the slag pool, and the Joule heat near the middle of the two electrodes is greater than the rest. With the increase in the current frequency, the current density distribution in the slag cell is basically unchanged. The current density inside the two electrodes increases obviously with the current frequency. When the current frequency increases from 10 Hz to 50 Hz, the maximum current density at the inner surface of the electrode increases by 14.7%. The current distribution at the lower side of the electrode in the slag pool is relatively uniform, and the current density in this region decreases with the increase in the height of the slag pool and the increase in the depth of the electrode inserted into the slag pool.


  • Open Access

    Effect of Rare Earth Cerium Content on Manganese Sulfide in U75V Heavy Rail Steel

    by Chao Zhuo, Rui Liu, Zirong Zhao, Yulei Zhang, Xiaoshuai Hao, Huajie Wu, Yanhui Sun

    To study the effect of Ce on the morphology of manganese sulfide, we added different contents of Ce into U75V heavy rail steel. The composition and morphology of sulfide in steel were analyzed. The inclusions’ number, size, and aspect ratio were analyzed by automatic scanning electron microscope ASPEX. The results show that the inclusions in heavy rail steel without Ce are elongated MnS and irregular Al-Si-Ca-O inclusions. With the increase of Ce from 52 ppm to 340 ppm, the composition of main inclusions changes along the route of Ce2O2S-MnS → Ce2O2S-MnS-Ce2S3 → Ce2O2S-Ce3S4-Ce2S3 → Ce2O2S-Ce3S4-CeS. Ce has a noticeable spheroidization effect on MnS, which can make inclusions finely dispersed. When Ce content is 139 ppm, the average size of inclusions is the smallest. The mechanism of Ce-modified MnS was discussed by combining experimental results with thermodynamic calculations. Finally, the effect of Ce treatment on inhibiting MnS deformation was verified by simulated rolling.