Xiaopeng Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaopeng Zhang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Yue Li
Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, State Key Laboratory of Space Network and Communications, Tsinghua University, Beijing, China
7 shared publications - Zhijun Zhang
Department of Electronic Engineering, Tsinghua University, Beijing, China
7 shared publications - Kunpeng Wei
Xiaomi Communications Company Ltd., Beijing, China
5 shared publications Dawei Zhou
Honor Device Company Ltd., Beijing, China
3 shared publications- Libin Sun
Shanghai Jiao Tong University
3 shared publications - Changjiang Deng
Beijing Key Laboratory of Millimeter Wave and Terahertz Technology, School of Integrated Circuits and Electronics, Beijing Institute of Technology, Beijing, China
1 shared publication
Latest Publications
- 8 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (8) , 2511-2515
A Circularly Polarized Antenna Based on Narrowed Crossed Dipole for Smartphone Satellite Communication
A circularly polarized (CP) antenna for satellite communication on smartphone is proposed in this article. The antenna is designed based on proposed narrowed crossed dipole, which has a significantly smaller size compared to the conventional one. Only one of the dipoles is excited directly, the other works as a parasitic element. By adjusting the lengths of the dipoles, CP radiation is realized. Finally, a matching circuit based on coupled microstrip line and balun chip for balanced feeding is introduced. A prototype of the proposed antenna was fabricated and tested to validate the concept. The measured bandwidth with S11 < -10 dB for the antenna is 2.47 – 2.51 GHz (covering the S band of the BeiDou Navigation Satellite System (BDS) of 2483.5 ∼ 2500 MHz). Besides, the measured 3 dB axial ratio (AR) bandwidth is about 1.4%. The maximum gain is 1.9 dBic and the efficiency is higher than 78% over the operating band. The proposed antenna shows great potential in the satellite communication application for smartphone.
- 8 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (8) , 2511-2515
A Circularly Polarized Antenna Based on Narrowed Crossed Dipole for Smartphone Satellite Communication
A circularly polarized (CP) antenna for satellite communication on smartphone is proposed in this article. The antenna is designed based on proposed narrowed crossed dipole, which has a significantly smaller size compared to the conventional one. Only one of the dipoles is excited directly, the other works as a parasitic element. By adjusting the lengths of the dipoles, CP radiation is realized. Finally, a matching circuit based on coupled microstrip line and balun chip for balanced feeding is introduced. A prototype of the proposed antenna was fabricated and tested to validate the concept. The measured bandwidth with S11 < -10 dB for the antenna is 2.47 – 2.51 GHz (covering the S band of the BeiDou Navigation Satellite System (BDS) of 2483.5 ∼ 2500 MHz). Besides, the measured 3 dB axial ratio (AR) bandwidth is about 1.4%. The maximum gain is 1.9 dBic and the efficiency is higher than 78% over the operating band. The proposed antenna shows great potential in the satellite communication application for smartphone.
- Open Access
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (3) , 612-619
Investigation of a Circularly Polarized Log-Periodic Dipole Antenna
In this letter, a circularly-polarized (CP) log-periodic dipole antenna (LPDA) is investigated. Eight crossed dipole cells with a logarithmically increased $\lambda $ /8 separation are employed to form the proposed CP LPDA. The dipoles with increased length and spacing are fed in series by an air-filled parallel line. The working mechanism of the generation of back-fire CP radiation is illustrated by an array analyzation. Besides, the LPDA design factors for both polarizations are analyzed in detail to realize an optimized CP performance. To validate the performance of the proposed eight-element CP LPDA, a prototype was fabricated and measured. The measured axial ratio (AR) bandwidth (0.8-2.5 GHz) is coincident with the impedance bandwidth (0.8-2.43 GHz), and it can be further increased with more elements. The overlapping bandwidth with VSWR < 2, AR < 3 dB, gain variation < 3 dB, and back-fire gain > 5 dBic is 0.94-2.43 GHz (2.6:1), and the radiation pattern is stable across the entire band.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (3) , 612-619
Open AccessInvestigation of a Circularly Polarized Log-Periodic Dipole Antenna
In this letter, a circularly-polarized (CP) log-periodic dipole antenna (LPDA) is investigated. Eight crossed dipole cells with a logarithmically increased $\lambda $ /8 separation are employed to form the proposed CP LPDA. The dipoles with increased length and spacing are fed in series by an air-filled parallel line. The working mechanism of the generation of back-fire CP radiation is illustrated by an array analyzation. Besides, the LPDA design factors for both polarizations are analyzed in detail to realize an optimized CP performance. To validate the performance of the proposed eight-element CP LPDA, a prototype was fabricated and measured. The measured axial ratio (AR) bandwidth (0.8-2.5 GHz) is coincident with the impedance bandwidth (0.8-2.43 GHz), and it can be further increased with more elements. The overlapping bandwidth with VSWR < 2, AR < 3 dB, gain variation < 3 dB, and back-fire gain > 5 dBic is 0.94-2.43 GHz (2.6:1), and the radiation pattern is stable across the entire band.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (12) , 9938-9943
A Polarization Reconfigurable Antenna for Satellite Communication in Foldable Smartphone
A polarization reconfigurable antenna based on dipoles is proposed for foldable smartphones in this article. Two dipoles, a driven dipole and a parasitic dipole, are placed on the top of the two parts of the foldable phone. The induced current on the parasitic dipole is similar in amplitude to the current on the driven dipole, with a phase difference of 90°. When the two parts of the phone are at 90°, the two dipoles are L-arranged orthogonally, realizing circularly polarized (CP) radiation. When the phone is in the fully unfolded or fully folded state, the proposed antenna can still work with linearly polarized (LP) radiation. Users can freely choose the folded state for satellite communication. A prototype for three different states was fabricated and tested to validate the concept. The measured bandwidth with S 11 < -10 dB for the antenna in each state can cover the target band 2.483 - 2.5 GHz. Besides, the measured 3 dB axial ratio (AR) bandwidth of the antenna in CP state is 2.464 - 2.516 GHz. The maximum gains of the three states are 3.9, 5.9 and 4.1 dBi over the operating band. The efficiencies are higher than 70%. The proposed antenna shows great potential in the satellite communication application for foldable smartphone.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (12) , 9938-9943
A Polarization Reconfigurable Antenna for Satellite Communication in Foldable Smartphone
A polarization reconfigurable antenna based on dipoles is proposed for foldable smartphones in this article. Two dipoles, a driven dipole and a parasitic dipole, are placed on the top of the two parts of the foldable phone. The induced current on the parasitic dipole is similar in amplitude to the current on the driven dipole, with a phase difference of 90°. When the two parts of the phone are at 90°, the two dipoles are L-arranged orthogonally, realizing circularly polarized (CP) radiation. When the phone is in the fully unfolded or fully folded state, the proposed antenna can still work with linearly polarized (LP) radiation. Users can freely choose the folded state for satellite communication. A prototype for three different states was fabricated and tested to validate the concept. The measured bandwidth with S 11 < -10 dB for the antenna in each state can cover the target band 2.483 - 2.5 GHz. Besides, the measured 3 dB axial ratio (AR) bandwidth of the antenna in CP state is 2.464 - 2.516 GHz. The maximum gains of the three states are 3.9, 5.9 and 4.1 dBi over the operating band. The efficiencies are higher than 70%. The proposed antenna shows great potential in the satellite communication application for foldable smartphone.
- 1 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (8) , 6941-6946
Pattern Reshaping of the Third Resonant Mode of Dipole and Slot Using Parasitic Elements
A simple approach for radiation pattern reshaping of the 3rd mode of dipole and slot antennas is proposed. Short parasitic strips or slots are added to both sides of the dipole or slot antenna. In the 3rd mode, the reversed current or E-field will destroy the omnidirectivity or bidirectivity of these two antennas. But, the induced current or E-field on the parasitic elements is opposite to that on the original antenna canceling the effect of the reversed current or E-field. As a result, the radiation patterns of the dipole and slot in the 3rd mode are reshaped to be omnidirectional or bidirectional, respectively. The effects of parasitic element length, spacing and position on radiation pattern have also been studied. Besides, it is proved that parasitic loops have the same effect. For simplifying impedance matching, a novel feeding method for slot antenna is designed specially without using lumped element. Two prototypes, dipole and slot antennas with parasitic elements, were fabricated and tested to validate the concept. The measured results are in good agreement with the simulated ones. The measured patterns of the 3rd mode are shaped with lower sidelobes and high realized gains. In both the 1st and 3rd modes, the dipole and slot antennas realize omnidirectional and bidirectional radiations, respectively.
- 1 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (8) , 6941-6946
Pattern Reshaping of the Third Resonant Mode of Dipole and Slot Using Parasitic Elements
A simple approach for radiation pattern reshaping of the 3rd mode of dipole and slot antennas is proposed. Short parasitic strips or slots are added to both sides of the dipole or slot antenna. In the 3rd mode, the reversed current or E-field will destroy the omnidirectivity or bidirectivity of these two antennas. But, the induced current or E-field on the parasitic elements is opposite to that on the original antenna canceling the effect of the reversed current or E-field. As a result, the radiation patterns of the dipole and slot in the 3rd mode are reshaped to be omnidirectional or bidirectional, respectively. The effects of parasitic element length, spacing and position on radiation pattern have also been studied. Besides, it is proved that parasitic loops have the same effect. For simplifying impedance matching, a novel feeding method for slot antenna is designed specially without using lumped element. Two prototypes, dipole and slot antennas with parasitic elements, were fabricated and tested to validate the concept. The measured results are in good agreement with the simulated ones. The measured patterns of the 3rd mode are shaped with lower sidelobes and high realized gains. In both the 1st and 3rd modes, the dipole and slot antennas realize omnidirectional and bidirectional radiations, respectively.
- 1 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (8) , 1997-2001
A Simple ±45° Polarized Patch Antenna Array Based on Single-Sided PCB for Wi-Fi 6/6E Application
A high gain, broadband, and ±45° polarized patch antenna array with a quite simple configuration for Wi-Fi 6/6E application is proposed in this article. The antenna consists of a substrate board and a metal layer. All the patches and feeding circuits are printed on the bottom surface of the board. The patches are excited by T-shaped dipoles which are driven by parallel dual-lines. The parameters of the dipoles and parallel dual-lines are specially designed to achieve a broadband covering both 5 GHz and 6 GHz bands of Wi-Fi 6/6E. A prototype was fabricated and tested to validate the concept. In agreement with the simulated results, the measured bandwidth with S 11 < -10 dB for two ports are both 5.00 - 7.50 GHz, with the isolation higher than 22 dB. Besides, the measured gains for two ports are higher than 9.80 and 9.38 dBi over the operating band. Compared with other unidirectional antennas, the proposed antenna shows great advantages in high gain, low cost, and easy processing.
- 1 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (8) , 1997-2001
A Simple ±45° Polarized Patch Antenna Array Based on Single-Sided PCB for Wi-Fi 6/6E Application
A high gain, broadband, and ±45° polarized patch antenna array with a quite simple configuration for Wi-Fi 6/6E application is proposed in this article. The antenna consists of a substrate board and a metal layer. All the patches and feeding circuits are printed on the bottom surface of the board. The patches are excited by T-shaped dipoles which are driven by parallel dual-lines. The parameters of the dipoles and parallel dual-lines are specially designed to achieve a broadband covering both 5 GHz and 6 GHz bands of Wi-Fi 6/6E. A prototype was fabricated and tested to validate the concept. In agreement with the simulated results, the measured bandwidth with S 11 < -10 dB for two ports are both 5.00 - 7.50 GHz, with the isolation higher than 22 dB. Besides, the measured gains for two ports are higher than 9.80 and 9.38 dBi over the operating band. Compared with other unidirectional antennas, the proposed antenna shows great advantages in high gain, low cost, and easy processing.
- 12 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (11) , 11143-11148
A Simple Dual-Polarized Patch Antenna Array for Wi-Fi 6/6E Application
A simple, high gain and dual-polarized patch antenna array for Wi-Fi 6/6E application is proposed in this article. Different from the conventional feeding method, the patches are driven by coupling dipoles which are printed on the same board. The dipoles are specially designed to be T-shaped to adjust the impedance matching. Broadband covering both 5 GHz and 6 GHz bands of Wi-Fi 6/6E is achieved. The feeding circuit is easily integrated on the board with only parallel dual-line utilized. A prototype is fabricated and tested to validate the concept. The measured and simulated results are in good agreement. The measured bandwidth with S11 < - 10 dB for two ports are 5.12 – 7.50 GHz and 5.15 – 7.50 GHz respectively, with the isolation higher than 30 dB. Moreover, the measured gains are higher than 9.76 and 9.61 dBi for two ports over the operating band with a peak value of 12.05 dBi. The proposed antenna array shows great potential in the application of Wi-Fi mesh.
- 12 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (11) , 11143-11148
A Simple Dual-Polarized Patch Antenna Array for Wi-Fi 6/6E Application
A simple, high gain and dual-polarized patch antenna array for Wi-Fi 6/6E application is proposed in this article. Different from the conventional feeding method, the patches are driven by coupling dipoles which are printed on the same board. The dipoles are specially designed to be T-shaped to adjust the impedance matching. Broadband covering both 5 GHz and 6 GHz bands of Wi-Fi 6/6E is achieved. The feeding circuit is easily integrated on the board with only parallel dual-line utilized. A prototype is fabricated and tested to validate the concept. The measured and simulated results are in good agreement. The measured bandwidth with S11 < - 10 dB for two ports are 5.12 – 7.50 GHz and 5.15 – 7.50 GHz respectively, with the isolation higher than 30 dB. Moreover, the measured gains are higher than 9.76 and 9.61 dBi for two ports over the operating band with a peak value of 12.05 dBi. The proposed antenna array shows great potential in the application of Wi-Fi mesh.
- 13 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (6) , 4250-4258
A Broadband Dual-Antenna Pair Based on Half-Open Cavity With Horizontally Polarized Radiation for Wi-Fi 6/6E Application
A broadband and omnidirectional coverage dual-antenna pair with horizontally polarized (HP) radiation for Wi-Fi 6/6E application is presented in this article. The dual-antenna pair is composed of two open cavity antennas (OCA) with the apertures partially sealed. By sealing the aperture partially, the dimension of the proposed half-OCA (HOCA) is reduced dramatically without changing the matching bandwidth and the radiation performance. Compared with other OCAs with the omnidirectional radiation, the proposed dual-antenna pair realizes omnidirectional coverage in azimuth plane by the back-to-back combination of two unidirectional OCAs, which also makes the antenna have multiple-input multiple-output (MIMO) performance. Besides, a broadband covering both 5 and 6 GHz bands of Wi-Fi 6/6E is also achieved. A prototype was fabricated and tested to validate the concept. In well agreement with the simulated results, the measured bandwidth with $S_{11} < -10$ dB for two ports are 5.03–7.35 GHz and 5.09–7.53 GHz, respectively, with the isolation higher than 22.67 dB. Besides, the measured gain > 5 dBi and ECC < 0.05 are achieved over the operating band. The proposed antenna shows great potential in the Wi-Fi 6/6E application.
- 13 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (6) , 4250-4258
A Broadband Dual-Antenna Pair Based on Half-Open Cavity With Horizontally Polarized Radiation for Wi-Fi 6/6E Application
A broadband and omnidirectional coverage dual-antenna pair with horizontally polarized (HP) radiation for Wi-Fi 6/6E application is presented in this article. The dual-antenna pair is composed of two open cavity antennas (OCA) with the apertures partially sealed. By sealing the aperture partially, the dimension of the proposed half-OCA (HOCA) is reduced dramatically without changing the matching bandwidth and the radiation performance. Compared with other OCAs with the omnidirectional radiation, the proposed dual-antenna pair realizes omnidirectional coverage in azimuth plane by the back-to-back combination of two unidirectional OCAs, which also makes the antenna have multiple-input multiple-output (MIMO) performance. Besides, a broadband covering both 5 and 6 GHz bands of Wi-Fi 6/6E is also achieved. A prototype was fabricated and tested to validate the concept. In well agreement with the simulated results, the measured bandwidth with $S_{11} < -10$ dB for two ports are 5.03–7.35 GHz and 5.09–7.53 GHz, respectively, with the isolation higher than 22.67 dB. Besides, the measured gain > 5 dBi and ECC < 0.05 are achieved over the operating band. The proposed antenna shows great potential in the Wi-Fi 6/6E application.
- 25 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (12) , 8229-8236
A Grooved Half-Mode Waveguide Leaky-Wave Antenna for Vertically-Polarized Endfire Radiation
A high-gain low-profile leaky-wave antenna (LWA) for vertically-polarized (VP) fixed-beam endfire radiation is proposed in this article. The LWA is composed of two back-to-back half-mode waveguides with grooves etched at the margins of both radiation edges. By etching grooves, the phase velocity of the traveling wave can be tailored to slower than the wave velocity in free space for fitting the Hansen–Woodyard condition. Compared with periodic LWAs, the proposed antenna continuously radiates at two symmetric apertures, contributing to a high endfire gain. A prototype is fabricated and tested to validate the concept. The measured and simulated results are in good agreement. A simulated gain of 14.29 dBi and a measured gain of 13.37 dBi are achieved within an antenna length of $3.05\lambda _{0}$ . Moreover, a measured overlapping bandwidth of 2.74–3.17 GHz (14.3%) is realized with $S_{11} < - 10$ dB and gain variation less than 3 dB. To the best of the authors’ knowledge, the proposed VP endfire LWA realizes the highest aperture efficiency and shows great advantages in high gain, low profile, and wide bandwidth.
- 25 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (12) , 8229-8236
A Grooved Half-Mode Waveguide Leaky-Wave Antenna for Vertically-Polarized Endfire Radiation
A high-gain low-profile leaky-wave antenna (LWA) for vertically-polarized (VP) fixed-beam endfire radiation is proposed in this article. The LWA is composed of two back-to-back half-mode waveguides with grooves etched at the margins of both radiation edges. By etching grooves, the phase velocity of the traveling wave can be tailored to slower than the wave velocity in free space for fitting the Hansen–Woodyard condition. Compared with periodic LWAs, the proposed antenna continuously radiates at two symmetric apertures, contributing to a high endfire gain. A prototype is fabricated and tested to validate the concept. The measured and simulated results are in good agreement. A simulated gain of 14.29 dBi and a measured gain of 13.37 dBi are achieved within an antenna length of $3.05\lambda _{0}$ . Moreover, a measured overlapping bandwidth of 2.74–3.17 GHz (14.3%) is realized with $S_{11} < - 10$ dB and gain variation less than 3 dB. To the best of the authors’ knowledge, the proposed VP endfire LWA realizes the highest aperture efficiency and shows great advantages in high gain, low profile, and wide bandwidth.