Jose Manuel Lopez Lopez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jose Manuel Lopez Lopez has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Molpeceres
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
4 shared publications - David Muñoz Martín
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
4 shared publications - Gilberto Gómez Rosas
Department of Physics, University Centre for Exact Sciences and Engineering (CUCEI), University of Guadalajara, Blvd. Marcelino García Barragan #1421, Guadalajara 44430, Mexico
4 shared publications - Juan José Moreno-Labella
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
4 shared publications - Miguel Morales
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
4 shared publications - Carlos Rubio-González
Tecnológico de Monterrey
2 shared publications
Latest Publications
- Open Access
Effects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses
Laser shock processing (LSP) is a surface treatment technique used to enhance mechanical properties such as hardness, corrosion resistance, and wear resistance. This study investigates the effects of LSP on a 6061-T6 aluminium alloy using four treatment conditions: nanosecond (ns-LSP), picosecond (ps-LSP), and a combination of nanosecond–picosecond (nsps-LSP) and picosecond–nanosecond (psns-LSP) pulses. Two laser systems were employed: a Q-switched Nd:YAG laser (850 mJ/pulse, 6 ns, 1064 nm, 10 Hz), and an Ekspla Atlantic 355-60 laser (0.110 mJ/pulse, 13 ps, 1064 nm, 1 kHz). All treatments induced compressive residual stresses up to 1 mm in depth. Additionally, improvements in microhardness were observed, particularly at deeper layers in the combined nsps-LSP treatment. Surface roughness was measured and compared. Among all configurations, the nsps-LSP treatment produced the highest compressive residual stresses (−428 MPa) and greater microhardness at depth. These results suggest that the combined nsps-LSP treatment represents a promising approach to enhance the mechanical performance of metallic components.
Open AccessEffects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses
Laser shock processing (LSP) is a surface treatment technique used to enhance mechanical properties such as hardness, corrosion resistance, and wear resistance. This study investigates the effects of LSP on a 6061-T6 aluminium alloy using four treatment conditions: nanosecond (ns-LSP), picosecond (ps-LSP), and a combination of nanosecond–picosecond (nsps-LSP) and picosecond–nanosecond (psns-LSP) pulses. Two laser systems were employed: a Q-switched Nd:YAG laser (850 mJ/pulse, 6 ns, 1064 nm, 10 Hz), and an Ekspla Atlantic 355-60 laser (0.110 mJ/pulse, 13 ps, 1064 nm, 1 kHz). All treatments induced compressive residual stresses up to 1 mm in depth. Additionally, improvements in microhardness were observed, particularly at deeper layers in the combined nsps-LSP treatment. Surface roughness was measured and compared. Among all configurations, the nsps-LSP treatment produced the highest compressive residual stresses (−428 MPa) and greater microhardness at depth. These results suggest that the combined nsps-LSP treatment represents a promising approach to enhance the mechanical performance of metallic components.
- Open Access
- 16 September 2025
- Published by MDPI AG in Preprints.org
Effects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses
Laser shock processing (LSP) is a surface treatment technique used to enhance mechanical properties such as hardness, corrosion resistance, and wear resistance. This study investigates the effects of LSP on a 6061-T6 aluminium alloy using four treatment conditions: nanosecond (ns-LSP), picosecond (ps-LSP), and a combination of nanosecond-picosecond (nsps-LSP) and picosecond-nanosecond (psns-LSP) pulses. Two laser systems were employed: a Q-switched Nd:YAG laser (850 mJ/pulse, 6 ns, 1064 nm, 10 Hz), and an Ekspla Atlantic 355-60 laser (0.110 mJ/pulse, 13 ps, 1064 nm, 1 kHz). All treatments induced compressive residual stresses up to 1 mm in depth. Additionally, improvements in microhardness were observed, particularly at deeper layers in the combined nsps-LSP treatment. Surface roughness was measured and compared. Among all configurations, the nsps-LSP treatment produced the highest compressive residual stresses (428 MPa) and greater microhardness at depth. These results suggest that the combined nsps-LSP treatment represents a promising approach to enhance the mechanical performance of metallic components.
- 16 September 2025
- Published by MDPI AG in Preprints.org
Open AccessEffects of Laser Shock Processing on the Mechanical Properties of 6061-T6 Aluminium Alloy Using Nanosecond and Picosecond Laser Pulses
Laser shock processing (LSP) is a surface treatment technique used to enhance mechanical properties such as hardness, corrosion resistance, and wear resistance. This study investigates the effects of LSP on a 6061-T6 aluminium alloy using four treatment conditions: nanosecond (ns-LSP), picosecond (ps-LSP), and a combination of nanosecond-picosecond (nsps-LSP) and picosecond-nanosecond (psns-LSP) pulses. Two laser systems were employed: a Q-switched Nd:YAG laser (850 mJ/pulse, 6 ns, 1064 nm, 10 Hz), and an Ekspla Atlantic 355-60 laser (0.110 mJ/pulse, 13 ps, 1064 nm, 1 kHz). All treatments induced compressive residual stresses up to 1 mm in depth. Additionally, improvements in microhardness were observed, particularly at deeper layers in the combined nsps-LSP treatment. Surface roughness was measured and compared. Among all configurations, the nsps-LSP treatment produced the highest compressive residual stresses (428 MPa) and greater microhardness at depth. These results suggest that the combined nsps-LSP treatment represents a promising approach to enhance the mechanical performance of metallic components.
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12408, PC1240805-7
Picosecond laser shock micro-forming of stainless steel
A study of the of laser peen forming of thin stainless steel metal foils (50 μm thick) using a solid-state ps-pulsed laser, emitting at a wavelength of 1064 nm was conducted. The dependence of the bending angle and the radius of curvature on the energy per pulse, the treated area, the distance between lines, and the repetition rate of the treatment is presented. The study also shows that the bending effect is local, and it cannot be scaled by increasing the repetition rate, because the increase in temperature relaxes the superficial stresses previously induced.
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12408, PC1240805-7
Picosecond laser shock micro-forming of stainless steel
A study of the of laser peen forming of thin stainless steel metal foils (50 μm thick) using a solid-state ps-pulsed laser, emitting at a wavelength of 1064 nm was conducted. The dependence of the bending angle and the radius of curvature on the energy per pulse, the treated area, the distance between lines, and the repetition rate of the treatment is presented. The study also shows that the bending effect is local, and it cannot be scaled by increasing the repetition rate, because the increase in temperature relaxes the superficial stresses previously induced.
- Open Access
Picosecond Laser Shock Micro-Forming of Stainless Steel: Influence of High-Repetition Pulses on Thermal Effects
A study of the peen forming of thin stainless steel metal foils (50 thick) using a solid-state ps-pulsed laser, emitting at a wavelength of was conducted. The pitch distance between consecutive laser pulses was kept constant by tuning the laser repetition rate from 0.4 to 10 , and subsequently the scanning speed. The induced bending angle and the radius of curvature were used to measure the effect of the treatment. Their dependence on the pulse energy, the treated area, the distance between lines, and the laser repetition rate was studied. High repetition rates do not allow the sample to cool down, affecting the bending to the point of being negligible. An FEM simulation and experiments were carried out to prove that the increase in temperature due to high repetition rate can relax the stresses induced by laser peen treatment, thus preventing bending in the sample.Open AccessPicosecond Laser Shock Micro-Forming of Stainless Steel: Influence of High-Repetition Pulses on Thermal Effects
A study of the peen forming of thin stainless steel metal foils (50 thick) using a solid-state ps-pulsed laser, emitting at a wavelength of was conducted. The pitch distance between consecutive laser pulses was kept constant by tuning the laser repetition rate from 0.4 to 10 , and subsequently the scanning speed. The induced bending angle and the radius of curvature were used to measure the effect of the treatment. Their dependence on the pulse energy, the treated area, the distance between lines, and the laser repetition rate was studied. High repetition rates do not allow the sample to cool down, affecting the bending to the point of being negligible. An FEM simulation and experiments were carried out to prove that the increase in temperature due to high repetition rate can relax the stresses induced by laser peen treatment, thus preventing bending in the sample. - 1 January 2017
- Published by Elsevier
- p. 151-169
Droplet-Assisted Laser Cleaning of Contaminated Surfaces
- 1 January 2017
- Published by Elsevier
- p. 151-169
Droplet-Assisted Laser Cleaning of Contaminated Surfaces
- Open Access
- 1 September 2016
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 36 (11) , 2689-2694
Droplet assisted laser micromachining of hard ceramics
- 1 September 2016
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 36 (11) , 2689-2694
Open AccessDroplet assisted laser micromachining of hard ceramics