MKMinki Kim

Minki Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Minki Kim has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Vision-Based Real-Time 3D Position Sensor for Spherical Actuators Using ICP Pose Estimation

    by Minoh Jeong, Junkyu Kim, Kyu-Sung Lee, Minki Kim

    This paper presents a vision-based real-time 3D position sensor for spherical actuators using Iterative Closest Point (ICP) pose estimation. Unlike conventional rotary motors with fixed axes, spherical actuators enable omnidirectional rotation, which makes traditional one-dimensional sensing methods, such as encoders, Hall sensors, and resolvers, unsuitable for accurate orientation measurement. To address this challenge, we propose a non-contact sensing approach that reconstructs three-dimensional surface point clouds from monocular camera images and estimates the full 3D orientation of the spherical rotor. Arbitrary and non-uniform visual patterns are applied to the rotor surface, and both intentional patterns and natural surface imperfections (e.g., scratches, dust, and wear) are exploited as geometric features for pose estimation. Edge features are extracted using Canny edge detection, reconstructed into 3D point clouds through a geometrically consistent mapping model, and aligned via ICP to estimate the spherical angles θ and ϕ. Experimental validation is conducted using a spherical rotor with a diameter of 15 cm. Under single-axis rotations, a minimum mean absolute error of 0.45° in θ is achieved after pixel-per-revolution calibration. Under dynamic multi-axis rotational motions, the estimated tangential azimuth direction ϕ exhibits compact zero-centered error distributions within approximately 0.2°– 0.9°, confirming consistent 3D directional estimation. Long-term stability analysis further shows that cumulative angular error accumulation remains approximately 0.15° per degree under appropriate sensing conditions. A computational architecture comparison demonstrates the feasibility of real-time operation. The complete processing pipeline, including image preprocessing, 3D reconstruction, and ICP-based pose estimation, achieves a total processing time below 32 ms per frame, satisfying real-time requirements at 30 fps. These results confirm that the proposed vision-based sensor provides a robust, non-contact, and practical solution for real-time 3D orientation sensing in spherical actuator systems.

  • Design and Control of a Permanent Magnet Spherical Wheel Motor With a Radially Segmented Belt and a Virtual Shaft

    by Minki Kim, Kyu-Sung Lee

    A novel design for a permanent magnet spherical wheel motor (SWM) is proposed to enable controlled rotation direction while ensuring stable and precise rotational control. The proposed motor features a belt-shaped stator, which is derived from conventional motor systems but employs a belt-shaped structure, enhancing scalability and modularity. To regulate the rotation direction effectively, a virtual shaft mechanism is introduced, in which additional permanent magnets are placed orthogonally to the primary rotational direction, enabling controlled axis stabilization. A prototype SWM was developed with a single-phase, four-belt configuration and six stators per belt, and its operation was successfully demonstrated using Hall sensors, an FPGA-based controller, and parallel inverters. Under a 12 V dc-link and no-load conditions, the motor speed was controlled from 50 to 500 rpm by adjusting the PWM duty cycle. One of the key challenges in evaluating the motor’s performance was the lack of an established method for accurately measuring rotation direction and speed. To address this, we proposed and implemented two measurement approaches: 1) image processing-based tracking; and 2) tachometer-based speed detection. Using these measurement techniques, we further analyzed the motor’s behavior under a friction load of approximately 10 mN $\cdot$ m. The results demonstrated continuous 360-degree directional switching at 45-degree intervals, while maintaining a speed of 300 rpm. This article introduces a novel method for designing and controlling a permanent magnet SWM with adjustable rotation direction, demonstrating its feasibility for future mobility applications.


  • Duty and Phase Control of a Self-Synchronized Class E Rectifier for High-Frequency Wireless Power Transfer System

    by Minki Kim, Jungwon Choi

    This article proposes a high-frequency (HF) wireless power transfer (WPT) system using duty and phase control of a self-synchronized class E rectifier considering the nonlinear internal capacitance of field-effect transistors (FETs). In HF WPT systems ($>$$ \text{13.56}\,\text{MHz}$), the self-synchronized class E rectifier provides a precise gate signal by compensating for the propagation delay. However, when controlling the output power of the HF WPT system, the nonlinear capacitance $C_{\text{oss}}$ of FETs distorts the shape of the drain-voltage waveform, which reduces the efficiency due to nonzero-voltage switching or partial diode operation. To mitigate this issue, we propose an $\alpha$ (=duty ratio) and $\beta$ (=phase delay) control method for a self-synchronized class E rectifier while considering the nonlinear $C_{\text{oss}}$ of FET. To achieve robust control and performance of the HF WPT system, we employed a regression method to estimate the value of $C_{\text{oss}}$ more accurately. Specifically, considering the impact of $C_{\text{oss}}$ on the performance of the HF WPT system, we selected two optimized control points $P_{\text{max}}$ and $P_{\text{min}}$ and developed a first–order polynomial equation representing the relationship between $\alpha$ and $\beta$. Following the determined $\alpha$$\beta$ relationship, the output power of the WPT was adjusted by hysteresis control while maintaining the highest efficiency. In the experimental validation, the proposed WPT system achieved a conversion efficiency of 82% to 76% in the 160–90 W output power range. Finally, the effectiveness of the proposed control method was also verified in closed-loop control during dynamic operation from 160 to $100\,\mathrm{W}$, with a minimal ripple (1.7%) in the output power.


  • Design of a Spiral Coil for High-Frequency Wireless Power Transfer Systems Using Machine Learning

    by Minki Kim, Minoh Jeong, Martina Cardone, Jungwon Choi

    This paper presents a novel design method based on machine learning (ML) for a spiral coil in a wireless power transfer (WPT) system operating at high frequencies. While a MHz frequency operation provides high power density for battery-powered applications, optimizing the spiral coil design becomes challenging due to the complex electromagnetic analysis, such as skin and proximity effects. Even though a three-dimensional (3D) electromagnetic simulator provides a practical analysis of different coil structures, it cannot quickly optimize the coil design due to its computing time. Therefore, an ML-based method is first proposed to estimate the $Q$ factor of a spiral coil, a critical parameter to determine the efficiency of a WPT system. Towards this end, a feed-forward neural network is trained using around $20 \cdot 10^{3}$ data samples collected by using a 3D quasi-static electromagnetic field simulator. It is shown that this method is effective; that is, it ensures an accuracy of up to 96%. Then, a spiral coil design method leveraging the designed ML-based $Q$ factor estimation is proposed. This method offers high performance (the intersection over union metric takes values up to 70%) and significant computation time savings (at least five orders of magnitude), compared to commonly adopted software simulators. Finally, the effectiveness of the proposed method is verified by the actual fabrication of several spiral coils.


  • Open Access

    Wireless dielectrophoresis trapping and remote impedance sensing via resonant wireless power transfer

    by Christopher T. Ertsgaard, Minki Kim, Jungwon Choi, Sang-Hyun Oh

    Nearly all biosensing platforms can be described using two fundamental steps—collection and detection. Target analytes must be delivered to a sensing element, which can then relay the transduced signal. For point-of-care technologies, where operation is to be kept simple, typically the collection step is passive diffusion driven—which can be slow or limiting under low concentrations. This work demonstrates an integration of both active collection and detection by using resonant wireless power transfer coupled to a nanogap capacitor. Nanoparticles suspended in deionized water are actively trapped using wireless dielectrophoresis and positioned within the most sensitive fringe field regions for wireless impedance-based detection. Trapping of 40 nm particles and larger is demonstrated using a 3.5 VRMS, 1 MHz radiofrequency signal delivered over a distance greater than 8 cm from the nanogap capacitor. Wireless trapping and release of 1 µm polystyrene beads is simultaneously detected in real-time over a distance of 2.5 cm from the nanogap capacitor. Herein, geometric scaling strategies coupled with optimal circuit design is presented to motivate combined collection and detection biosensing platforms amenable to wireless and/or smartphone operation.


  • Self-Synchronized Class E Resonant Rectifier by Compensating Propagation Delay for Multi-MHz Switching Applications

    by Minki Kim, Jungwon Choi

    In this article, a self-synchronized, high-frequency class E resonant rectifier is proposed to compensate for the synchronization signal mismatch due to the propagation delay. The synchronous rectification helps the power conversion system increase its efficiency by using active devices such as mosfets instead of diodes. Even with the mosfets , it is still challenging to generate an accurate synchronous signal from the input source in the multi-MHz wireless power transfer (WPT) systems due to the propagation delay from the integrated circuit (IC) components and the gate driver. In general, the propagation delay is more than 10 ns, a significant period in the multi-MHz operation. To mitigate the propagation delay, we present the self-synchronized rectifier, sensing the signal in the $C_{s}$ - $L_{s}$ network. The proposed design creates a proper gate signal to the active device in the rectifier by measuring the voltage of the node between $C_{s}$ - $L_{s}$ resonant filter. In the experiments, we tested the driving method in the class E rectifier at an output power of 228 W and a switching frequency of 13.56 MHz. While the total propagation delay was 8 ns, including the gate-driver and comparator, the leading phase of the sensing voltage successfully offsets the driver’s propagation delay.


  • Design of Robust Capacitive Power Transfer Systems Using High-Frequency Resonant Inverters

    by Minki Kim, Jungwon Choi

    This article presents a novel approach using a resonant inverter operating at 6.78 MHz for a robust capacitive power transfer (CPT) system with a small air gap. The flexible design process of a class $\Phi _2$ inverter to select the capacitance in the load network allows us to maintain high efficiency without a compensation inductor to mitigate misalignments between coupling plates. The capacitor in the class $\Phi _2$ inverter can be any value above 3 nF at megahertzs frequencies because it is not in resonance but provides dc blocking. If the capacitance value varies in the range above 3 nF, it does not affect the performance of the inverter and the CPT system. We design a push–pull class $\Phi _2$ inverter to provide isolation between the transmitting and receiving sides by nature and easily increase the output power twice. In addition, compared with the previous CPT system, the proposed inverter can increase the output power, while the misalignment between coupling plates increases because of the nonresonant load network. The designed coupling capacitor with a Kapton film has a capacitance value above 4.6 nF, even with a 15-cm misalignment. We also simulate the design in Ansys Maxwell HFSS to examine the electric fields. We present simulated and experimental measurements of the push–pull class $\Phi _2$ inverter with the designed coupling capacitor. The system’s nominal output power was 277 W with a 86.65% efficiency at an input voltage of 50 V. With the misalignments up to 15 cm, the efficiency is almost constant, 87% (80% at dc-to-dc CPT system), while the capacitance of the coupling plates varies from 8.82 to 4.62 nF.