Qipeng Tang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qipeng Tang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Anwen Shen
National Key Laboratory of Science and Technology on Multispectral Information Processing and Key Laboratory of Image Processing and Intelligent Control, School of Artificial Intelligence and Automation, Huazhong University of Science and Technology, Wuhan, China
11 shared publications - Jinbang Xu
National Key Laboratory of Science and Technology on Multispectral Information Processing and Key Laboratory of Image Processing and Intelligent Control, School of Artificial Intelligence and Automation, Huazhong University of Science and Technology, Wuhan, China
9 shared publications - Xin Luo
School of Artificial Intelligence and Automation, National Key Laboratory of Science and Technology on Multispectral Information Processing and Key Laboratory of Image Processing and Intelligent Control, Huazhong University of Science and Technology (HUST), Wuhan, China
8 shared publications - Pan Luo
National Key Laboratory of Science and Technology on Multispectral Information Processing and Key Laboratory of Image Processing and Intelligent Control, School of Artificial Intelligence and Automation, Huazhong University of Science and Technology, Wuhan, China
6 shared publications Xin Luo
School of Artificial Intelligence and Automation, Key Laboratory of Image Processing and Intelligent Control, Huazhong University of Science and Technology, Wuhan, Peoples Republic of China
4 shared publicationsAnwen Shen
School of Artificial Intelligence and Automation, Key Laboratory of Image Processing and Intelligent Control, Huazhong University of Science and Technology, Wuhan, Peoples Republic of China
3 shared publications
Latest Publications
- 6 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Minimum-Delay Deadbeat Predictive Current Control Strategy with Model Mismatch Compensation for SPMSM Drives
Deadbeat predictive current control (DPCC) scheme has been widely applied in permanent magnet synchronous motor (PMSM) drive systems due to its superior dynamic response and current tracking performance. However, the control performance of conventional DPCC is susceptible to inherent one-step control delays and motor parameter mismatches. To address these challenges, a minimum-delay DPCC (MD-DPCC) strategy with model mismatch compensation is proposed in this paper. Differing from conventional method that relies on the average stator voltage equations of the motor, the proposed strategy constructs the transient current ripple prediction model by minimizing the delay between the sampling instant and system update instant. This prediction model ensures high performance and robustness even when affected by nonlinear disturbances such as model parameter mismatches. Furthermore, the mathematical expression of this transient model at various sampling instants is derived and discussed in detail. To further enhance steady-state accuracy, an improved feedback correction loop is introduced, which leverages the high-precision current prediction to effectively eliminate steady-state errors. Finally, experimental results conducted on a SPMSM drive platform based on STM32H742 validate that the proposed MD-DPCC strategy achieves fast and precise current tracking as well as strong robustness to model parameter variations.
- 6 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Minimum-Delay Deadbeat Predictive Current Control Strategy with Model Mismatch Compensation for SPMSM Drives
Deadbeat predictive current control (DPCC) scheme has been widely applied in permanent magnet synchronous motor (PMSM) drive systems due to its superior dynamic response and current tracking performance. However, the control performance of conventional DPCC is susceptible to inherent one-step control delays and motor parameter mismatches. To address these challenges, a minimum-delay DPCC (MD-DPCC) strategy with model mismatch compensation is proposed in this paper. Differing from conventional method that relies on the average stator voltage equations of the motor, the proposed strategy constructs the transient current ripple prediction model by minimizing the delay between the sampling instant and system update instant. This prediction model ensures high performance and robustness even when affected by nonlinear disturbances such as model parameter mismatches. Furthermore, the mathematical expression of this transient model at various sampling instants is derived and discussed in detail. To further enhance steady-state accuracy, an improved feedback correction loop is introduced, which leverages the high-precision current prediction to effectively eliminate steady-state errors. Finally, experimental results conducted on a SPMSM drive platform based on STM32H742 validate that the proposed MD-DPCC strategy achieves fast and precise current tracking as well as strong robustness to model parameter variations.
- 14 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 5214-5224
Dual-MRAS Sensorless Control of SPMSM Based on Model Predictive Current Control
In the sensorless control of surface-mounted permanent magnet synchronous motors (SPMSMs), the model reference adaptive system (MRAS) is known for its favorable dynamic performance. However, the conventional MRAS method, which estimates the rotor position by integrating the speed estimation results, inherently results in a relatively slow convergence rate of position errors during dynamic control. To address this issue, a dual MRAS sensorless control method based on model predictive current control (MPCC) is proposed in this article. A novel dual MRAS scheme for rotor speed and position error estimation is constructed, leveraging two components of the total electromotive force (EMF) in the synchronous rotating frame through distinct estimation and prediction models. Small-signal analysis reveals that the position error equation transitions from a second-order system in the traditional method to a zero-order system in the proposed method, thereby enabling faster response and reduced dynamic position estimation errors. Furthermore, by incorporating MPCC into the current loop, the proposed method achieves a closed-loop prediction, thereby enhancing estimation accuracy and the dynamic response performance. Comprehensive experimental validations are conducted to evaluate the performance of the proposed dual MRAS method based on MPCC (D-MRAS-MPCC) methodology. The results demonstrate that the proposed method exhibits superior dynamic control performance compared to the conventional MRAS method.
- 14 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 5214-5224
Dual-MRAS Sensorless Control of SPMSM Based on Model Predictive Current Control
In the sensorless control of surface-mounted permanent magnet synchronous motors (SPMSMs), the model reference adaptive system (MRAS) is known for its favorable dynamic performance. However, the conventional MRAS method, which estimates the rotor position by integrating the speed estimation results, inherently results in a relatively slow convergence rate of position errors during dynamic control. To address this issue, a dual MRAS sensorless control method based on model predictive current control (MPCC) is proposed in this article. A novel dual MRAS scheme for rotor speed and position error estimation is constructed, leveraging two components of the total electromotive force (EMF) in the synchronous rotating frame through distinct estimation and prediction models. Small-signal analysis reveals that the position error equation transitions from a second-order system in the traditional method to a zero-order system in the proposed method, thereby enabling faster response and reduced dynamic position estimation errors. Furthermore, by incorporating MPCC into the current loop, the proposed method achieves a closed-loop prediction, thereby enhancing estimation accuracy and the dynamic response performance. Comprehensive experimental validations are conducted to evaluate the performance of the proposed dual MRAS method based on MPCC (D-MRAS-MPCC) methodology. The results demonstrate that the proposed method exhibits superior dynamic control performance compared to the conventional MRAS method.
- 20 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4996-5008
SynRM Sensorless MTPA Integrated Control Strategy Based on PWM-Induced Transient Excitation Considering Cross-Saturation Effects
This article proposes a sensorless maximum-torque-per-ampere (MTPA) integrated control strategy to maximize the driving efficiency of synchronous reluctance motors (SynRM) having cross-saturation effects without any position sensors. Differing from the conventional method that the rotor position estimation and the MTPA tracking trajectory are two separate processes, the proposed strategy can achieve sensorless MTPA one-step direct control of the SynRM. With the proposed strategy, five independent equations are firstly constructed and extracted from the pulsewidth modulation (PWM) induced transient excitation currents. By solving these equations, the optimal MTPA current space vector angle can be calculated directly without any motor parameters, which not only greatly simplifies the whole implementation process, but also effectively eliminates the influences of the motor saturation and parameters uncertainties. Meanwhile, aiming at those inapplicable modulation areas where there are not enough suitable voltage vectors to satisfy minimum time demand for the slope sampling of response currents, such as ultralow or ultrahigh modulation, and sector-boundary region, the corresponding dimensionality reduction compensation scheme and modified PWM compensation solution are described in detail. Finally, experimental results indicate that the proposed direct control strategy can achieve the high-performance sensorless control with accurate MTPA self-tracking operation in the entire linear modulation region.
- 20 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4996-5008
SynRM Sensorless MTPA Integrated Control Strategy Based on PWM-Induced Transient Excitation Considering Cross-Saturation Effects
This article proposes a sensorless maximum-torque-per-ampere (MTPA) integrated control strategy to maximize the driving efficiency of synchronous reluctance motors (SynRM) having cross-saturation effects without any position sensors. Differing from the conventional method that the rotor position estimation and the MTPA tracking trajectory are two separate processes, the proposed strategy can achieve sensorless MTPA one-step direct control of the SynRM. With the proposed strategy, five independent equations are firstly constructed and extracted from the pulsewidth modulation (PWM) induced transient excitation currents. By solving these equations, the optimal MTPA current space vector angle can be calculated directly without any motor parameters, which not only greatly simplifies the whole implementation process, but also effectively eliminates the influences of the motor saturation and parameters uncertainties. Meanwhile, aiming at those inapplicable modulation areas where there are not enough suitable voltage vectors to satisfy minimum time demand for the slope sampling of response currents, such as ultralow or ultrahigh modulation, and sector-boundary region, the corresponding dimensionality reduction compensation scheme and modified PWM compensation solution are described in detail. Finally, experimental results indicate that the proposed direct control strategy can achieve the high-performance sensorless control with accurate MTPA self-tracking operation in the entire linear modulation region.
- 15 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4945-4957
Voltage-Vector Optimal Redistribution-Based Hybrid PWM Strategy for Current Ripple Reduction in Three-Phase Two-Level Inverter
This article aims to reduce the current ripple for the three-phase two-level inverter in a wide operation range. Based on the thought of voltage-vector optimal redistribution, a hybrid pulsewidth modulation (PWM) strategy is proposed. Differing from conventional space-vector PWM scheme that the duration of zero-voltage and active-voltage vectors are always equally divided, the proposed hybrid PWM strategy redistributes the dwelling time of zero-voltage vectors and active-voltage vectors according to the minimum current ripple peak value. With the proposed strategy, the optimal PWM switching sequence-I based on zero-voltage vector redistribution is first obtained by establishing and analyzing the mathematical relationship of the current ripple peak value and the redistribution coefficient of the two zero-voltage vectors’ duration. Then, by splitting the dwelling time of maximum active-voltage vector based on the minimum current ripple peak value, meanwhile merging zero-voltage vectors according to the centrosymmetric modulation, the optimal PWM switching sequence-II and sequence-III are generated effectively and conveniently. With the comprehensive integration of three optimal PWM switching sequences, the proposed strategy not only reduces three-phase current ripples cooperatively and effectively, but also does not increase the total switching power loss. Finally, experimental results are provided to validate the effectiveness and feasibility of the proposed hybrid strategy.
- 15 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4945-4957
Voltage-Vector Optimal Redistribution-Based Hybrid PWM Strategy for Current Ripple Reduction in Three-Phase Two-Level Inverter
This article aims to reduce the current ripple for the three-phase two-level inverter in a wide operation range. Based on the thought of voltage-vector optimal redistribution, a hybrid pulsewidth modulation (PWM) strategy is proposed. Differing from conventional space-vector PWM scheme that the duration of zero-voltage and active-voltage vectors are always equally divided, the proposed hybrid PWM strategy redistributes the dwelling time of zero-voltage vectors and active-voltage vectors according to the minimum current ripple peak value. With the proposed strategy, the optimal PWM switching sequence-I based on zero-voltage vector redistribution is first obtained by establishing and analyzing the mathematical relationship of the current ripple peak value and the redistribution coefficient of the two zero-voltage vectors’ duration. Then, by splitting the dwelling time of maximum active-voltage vector based on the minimum current ripple peak value, meanwhile merging zero-voltage vectors according to the centrosymmetric modulation, the optimal PWM switching sequence-II and sequence-III are generated effectively and conveniently. With the comprehensive integration of three optimal PWM switching sequences, the proposed strategy not only reduces three-phase current ripples cooperatively and effectively, but also does not increase the total switching power loss. Finally, experimental results are provided to validate the effectiveness and feasibility of the proposed hybrid strategy.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (12) , 14722-14733
Model Predictive Control for Dual-Motor Driving System With Unknown Backlash Nonlinearity
The unmeasurable gear backlash nonlinearity caused by mechanical wear in multimotor driving systems (MDSs) is inevitable, imposing challenges for the modeling and controller design. As a remedy, this work proposes a model predictive controller (MPC) to handle the unmeasurable backlash often encountered in dual-motor driving systems (DDSs). First, a control-oriented model with an observer is established to estimate the backlash torque. Accordingly, a constrained MPC is developed to minimize both the tracking error and vibrations. Therein, delay compensation is leveraged to decrease prediction lag. PI feedback is introduced to compensate for the steady-state error caused by the offset of the external observer. Based on the output of the proposed MPC, which is the sum of the torques for two motors, a time-varying-bias-torque (TVBT) scheme to save energy consumption is designed to compute the torque for each motor. Finally, experiments are conducted on DDSs to verify the effectiveness and superiority of the present MPC-TVBT.
- 29 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (12) , 14722-14733
Model Predictive Control for Dual-Motor Driving System With Unknown Backlash Nonlinearity
The unmeasurable gear backlash nonlinearity caused by mechanical wear in multimotor driving systems (MDSs) is inevitable, imposing challenges for the modeling and controller design. As a remedy, this work proposes a model predictive controller (MPC) to handle the unmeasurable backlash often encountered in dual-motor driving systems (DDSs). First, a control-oriented model with an observer is established to estimate the backlash torque. Accordingly, a constrained MPC is developed to minimize both the tracking error and vibrations. Therein, delay compensation is leveraged to decrease prediction lag. PI feedback is introduced to compensate for the steady-state error caused by the offset of the external observer. Based on the output of the proposed MPC, which is the sum of the torques for two motors, a time-varying-bias-torque (TVBT) scheme to save energy consumption is designed to compute the torque for each motor. Finally, experiments are conducted on DDSs to verify the effectiveness and superiority of the present MPC-TVBT.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 10804-10815
Surface-PMSM Sensorless Control Strategy Based on Reduced-Order Linear Kalman Filter Cooperating With Prediction Error Rolling Compensation
Kalman filter (KF) is increasingly attracted for sensorless control of surface permanent magnet synchronous motors due to its strong robustness against measurement and system noise. However, the conventional method suffers from poor position and speed estimation accuracy under dynamic conditions and high computational cost. In order to solve these problems, an enhanced sensorless control strategy based on reduced-order linear Kalman filter (RLKF) cooperating with prediction error rolling compensation is introduced in this article. Differing from conventional methods, a reduced-order linear state equation encompassing rotor position, speed, and torque disturbance is constructed. Then, by obtaining the prediction error of system output using the motor current equation in the predictive reference frame, the optimal estimation of rotor position and speed in the KF algorithm is achieved based on the reduced-order model. This not only simplifies the calculation process but also enhances the position and speed estimation accuracy under dynamic conditions. Meanwhile, a prediction error rolling compensation algorithm is developed to minimize the estimation deviations caused by motor parameter variations. In addition, the system's dynamic performance is further improved with an adopted speed controller based on torque disturbance feedforward and acceleration feedback. Finally, experimental results verify the effectiveness and feasibility of the proposed strategy.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 10804-10815
Surface-PMSM Sensorless Control Strategy Based on Reduced-Order Linear Kalman Filter Cooperating With Prediction Error Rolling Compensation
Kalman filter (KF) is increasingly attracted for sensorless control of surface permanent magnet synchronous motors due to its strong robustness against measurement and system noise. However, the conventional method suffers from poor position and speed estimation accuracy under dynamic conditions and high computational cost. In order to solve these problems, an enhanced sensorless control strategy based on reduced-order linear Kalman filter (RLKF) cooperating with prediction error rolling compensation is introduced in this article. Differing from conventional methods, a reduced-order linear state equation encompassing rotor position, speed, and torque disturbance is constructed. Then, by obtaining the prediction error of system output using the motor current equation in the predictive reference frame, the optimal estimation of rotor position and speed in the KF algorithm is achieved based on the reduced-order model. This not only simplifies the calculation process but also enhances the position and speed estimation accuracy under dynamic conditions. Meanwhile, a prediction error rolling compensation algorithm is developed to minimize the estimation deviations caused by motor parameter variations. In addition, the system's dynamic performance is further improved with an adopted speed controller based on torque disturbance feedforward and acceleration feedback. Finally, experimental results verify the effectiveness and feasibility of the proposed strategy.
- Open Access
- 11 October 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (15) , 2439-2450
Dynamic overmodulation strategy based on torque and flux optimal tracking for DTC‐SVM of surface‐mounted PMSM drives
Direct torque control with space vector modulation has been increasingly attracting emphasis for permanent‐magnet synchronous machine control, benefiting from a high dynamic response and low torque ripple. However, the rapid tracking performance of torque and stator flux linkage is gradually deteriorating as the machine enters the overmodulation region because of the output‐voltage limitation of the inverter. Therefore, to enhance the system tracking performance in the overmodulation region, an innovative overmodulation method based on torque and flux optimal tracking is proposed. In contrast to the conventional overmodulation method where only one of the torque and stator flux linkage tracking is considered, the proposed strategy first constructs the weightless cost function to achieve a trade‐off control between the torque and stator flux linkage. Then, by using an equivalent geometric path to intuitively express the weightless cost function, the minimum cost function can be easily solved and the optimal output voltage vector can be determined correspondingly, to achieve the fast‐tracking of both the torque and stator flux linkage. Additionally, the voltage utilization of different overmodulation schemes is also analysed. Finally, the experimental results demonstrate the efficiency and practicality of the proposed strategy.
- 11 October 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (15) , 2439-2450
Open AccessDynamic overmodulation strategy based on torque and flux optimal tracking for DTC‐SVM of surface‐mounted PMSM drives
Direct torque control with space vector modulation has been increasingly attracting emphasis for permanent‐magnet synchronous machine control, benefiting from a high dynamic response and low torque ripple. However, the rapid tracking performance of torque and stator flux linkage is gradually deteriorating as the machine enters the overmodulation region because of the output‐voltage limitation of the inverter. Therefore, to enhance the system tracking performance in the overmodulation region, an innovative overmodulation method based on torque and flux optimal tracking is proposed. In contrast to the conventional overmodulation method where only one of the torque and stator flux linkage tracking is considered, the proposed strategy first constructs the weightless cost function to achieve a trade‐off control between the torque and stator flux linkage. Then, by using an equivalent geometric path to intuitively express the weightless cost function, the minimum cost function can be easily solved and the optimal output voltage vector can be determined correspondingly, to achieve the fast‐tracking of both the torque and stator flux linkage. Additionally, the voltage utilization of different overmodulation schemes is also analysed. Finally, the experimental results demonstrate the efficiency and practicality of the proposed strategy.
- 9 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (4) , 2202-2215
A Novel Flux-Torque Decoupling Based Direct Torque Control Strategy for Surface Permanent Magnet Synchronous Motor Drives
Direct torque control (DTC) is increasingly attracted for high performance control of surface permanent magnet synchronous motors (SPMSMs) due to its easy implementation and fast dynamic response. However, the conventional switching-table-based method inevitably produces large torque and stator flux ripples because the selection of inverter's active-voltage vector is depending on the sign of torque and flux errors through hysteresis comparators regardless of their amplitude errors. To resolve these problems, a novel DTC strategy based on flux-torque decoupling is proposed in this paper. With the proposed method, two desired voltage vectors are firstly constructed to achieve the decoupling control of stator flux and torque by analyzing the relationships between applied voltage and torque and stator flux derivative. Afterwards, by applying vector synthesis to analyze the generation of two desired voltage vectors, the corresponding inverter's active-voltage vectors and their duty ratios are determined, so as to achieve the precise regulation of stator flux and torque with little ripples. Furthermore, in order to minimize the influence of machine parameters variations, a simple and real-time identification method for the ratio between permanent magnet flux linkage and stator inductance is presented. Finally, the experimental results indicate the effectiveness and feasibility of the proposed strategy
- 9 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (4) , 2202-2215
A Novel Flux-Torque Decoupling Based Direct Torque Control Strategy for Surface Permanent Magnet Synchronous Motor Drives
Direct torque control (DTC) is increasingly attracted for high performance control of surface permanent magnet synchronous motors (SPMSMs) due to its easy implementation and fast dynamic response. However, the conventional switching-table-based method inevitably produces large torque and stator flux ripples because the selection of inverter's active-voltage vector is depending on the sign of torque and flux errors through hysteresis comparators regardless of their amplitude errors. To resolve these problems, a novel DTC strategy based on flux-torque decoupling is proposed in this paper. With the proposed method, two desired voltage vectors are firstly constructed to achieve the decoupling control of stator flux and torque by analyzing the relationships between applied voltage and torque and stator flux derivative. Afterwards, by applying vector synthesis to analyze the generation of two desired voltage vectors, the corresponding inverter's active-voltage vectors and their duty ratios are determined, so as to achieve the precise regulation of stator flux and torque with little ripples. Furthermore, in order to minimize the influence of machine parameters variations, a simple and real-time identification method for the ratio between permanent magnet flux linkage and stator inductance is presented. Finally, the experimental results indicate the effectiveness and feasibility of the proposed strategy
- Open Access
- 1 January 2024
- Published by Wiley in Complexity
- Vol. 2024 (1)
Dual‐Sliding‐Mode‐Observer‐Based IPMSM Sensorless Control Technique
Back electromotive force (EMF)‐based sliding mode observer (SMO) is increasingly employed for interior permanent magnet synchronous machine (IPMSM) sensorless drives due to its high robustness to external disturbance and low sensitivity to system parameter variations. However, its control performance is severely weakened by the inherent chattering and speed iteration operation. In order to effectively resolve these problems, a strategy to design a dual‐SMO is proposed in this paper. With the proposed strategy, the combination of the stator‐voltage transformation matrix (SVTM) and the low‐pass filter is developed to obtain the rotor position information, which greatly alleviates the chattering without any deviations. Meanwhile, three independent equations are constructed and extracted by placing two SVTMs in different locations. By solving these three equations, the rotor position can be calculated directly with zero phase shift, which eliminates the speed iteration operation and improves the system’s dynamic performance. Furthermore, by analyzing the influences of machine parameters’ variations, the suitable virtual q‐axis inductance can be selected to quickly achieve the optimal‐efficiency sensorless control of the IPMSM. Finally, the experimental results on an IPMSM demonstrate that the rotor position with good steady‐state and dynamic performance can be obtained accurately by using the proposed sensorless control strategy.
- 1 January 2024
- Published by Wiley in Complexity
- Vol. 2024 (1)
Open AccessDual‐Sliding‐Mode‐Observer‐Based IPMSM Sensorless Control Technique
Back electromotive force (EMF)‐based sliding mode observer (SMO) is increasingly employed for interior permanent magnet synchronous machine (IPMSM) sensorless drives due to its high robustness to external disturbance and low sensitivity to system parameter variations. However, its control performance is severely weakened by the inherent chattering and speed iteration operation. In order to effectively resolve these problems, a strategy to design a dual‐SMO is proposed in this paper. With the proposed strategy, the combination of the stator‐voltage transformation matrix (SVTM) and the low‐pass filter is developed to obtain the rotor position information, which greatly alleviates the chattering without any deviations. Meanwhile, three independent equations are constructed and extracted by placing two SVTMs in different locations. By solving these three equations, the rotor position can be calculated directly with zero phase shift, which eliminates the speed iteration operation and improves the system’s dynamic performance. Furthermore, by analyzing the influences of machine parameters’ variations, the suitable virtual q‐axis inductance can be selected to quickly achieve the optimal‐efficiency sensorless control of the IPMSM. Finally, the experimental results on an IPMSM demonstrate that the rotor position with good steady‐state and dynamic performance can be obtained accurately by using the proposed sensorless control strategy.