Xincheng Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xincheng Xie has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jinrui Xiao
School of Mechanical and Electrical Engineering, Guangzhou University, 510006, Guangzhou, People’s Republic of China
5 shared publications - Zhongwei Liang
Guangzhou University
5 shared publications - Xiaochu Liu
School of Mechanical and Electrical Engineering, Guangzhou University, Guangzhou 510006, China
4 shared publications - Zhuan Zhao
School of Physics and Materials Science, Guangzhou University, Guangzhou 510006, China
4 shared publications Ben Deng
Shaoyang Victor Hydraulic Co., LTD, Shaoyang, China
1 shared publication- Gongbin Tang
School of Mechanical and Electric Engineering
1 shared publication
Latest Publications
- 17 January 2026
- Published by Elsevier in Ultrasonics
- Vol. 162, 107965
Composite layer formation on AZ91D magnesium alloy via temperature-assisted ultrasonic shot peening for enhanced wear resistance
- 17 January 2026
- Published by Elsevier in Ultrasonics
- Vol. 162, 107965
Composite layer formation on AZ91D magnesium alloy via temperature-assisted ultrasonic shot peening for enhanced wear resistance
- 1 March 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (3) , 1097-1102
Enhancing the wear resistance of 316L stainless steel through surface mechanical attrition treatment and polishing treatment
- 1 March 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (3) , 1097-1102
Enhancing the wear resistance of 316L stainless steel through surface mechanical attrition treatment and polishing treatment
- Open Access
Enhanced Strength–Ductility Synergy Properties in Selective Laser Melted 316L Stainless Steel by Strengthening Grinding Process
Selective laser melted (SLM) 316L stainless steel (SS) has been widely employed in the fields of designing and manufacturing components with complex shapes and sizes. However, the low yield strength, low ultimate tensile stress, and low hardness of SLM 316L SS components hinder its further application. In this work, the strengthening grinding process (SGP) was used to enhance the mechanical properties of SLM 316L SS. The microhardness, residual stress, microstructure, and tensile properties of all the samples were analyzed. The results demonstrate that the SGP induced higher compressive residual stress and microhardness, as well as higher tensile properties. The maximum hardness and residual stress reached 354.5 HV and −446 MPa, respectively, indicating that the SGP resulted in a plastic deformation layer over 150 μm. The possible mechanisms have been discussed in further detail. Compared to the untreated sample, the SGP sample shows a significant improvement in yield strength (YS), ultimate tensile stress (UTS), and elongation (EL), increasing 30%, 25.5%, and 99.1%, respectively. This work demonstrates that SGP treatment could be an efficient approach to simultaneously improving the strength and ductility of the SLM 316L SS, which makes it more suitable for engineering applications.
Open AccessEnhanced Strength–Ductility Synergy Properties in Selective Laser Melted 316L Stainless Steel by Strengthening Grinding Process
Selective laser melted (SLM) 316L stainless steel (SS) has been widely employed in the fields of designing and manufacturing components with complex shapes and sizes. However, the low yield strength, low ultimate tensile stress, and low hardness of SLM 316L SS components hinder its further application. In this work, the strengthening grinding process (SGP) was used to enhance the mechanical properties of SLM 316L SS. The microhardness, residual stress, microstructure, and tensile properties of all the samples were analyzed. The results demonstrate that the SGP induced higher compressive residual stress and microhardness, as well as higher tensile properties. The maximum hardness and residual stress reached 354.5 HV and −446 MPa, respectively, indicating that the SGP resulted in a plastic deformation layer over 150 μm. The possible mechanisms have been discussed in further detail. Compared to the untreated sample, the SGP sample shows a significant improvement in yield strength (YS), ultimate tensile stress (UTS), and elongation (EL), increasing 30%, 25.5%, and 99.1%, respectively. This work demonstrates that SGP treatment could be an efficient approach to simultaneously improving the strength and ductility of the SLM 316L SS, which makes it more suitable for engineering applications.
- Open Access
The Effect of the Displacement Amplitude on the Fretting Wear of GCr15 Steel with a TiC Coating
In the present paper, the effect of mechanical ball milling time on the fretting wear of GCr15 steel balls at different displacement amplitudes is investigated. TiC powder coating was fabricated on the surface of GCr15 steel balls using various process times, and the fretting wear tests were conducted on an AISI 52100 steel disk with the applied force of 80 N. Additionally, various displacement amplitudes (10 μm, 20 μm, and 60 μm) were selected. Specimen attributes and wear scars were characterized using an inverted metallographic microscope, a microhardness tester, an X-ray diffractometry analyzer, a white light interferometer, and a scanning electron microscope. The results showed that thick and continuous coatings could be obtained at the milling time of 18 h. The specimens processed for a longer milling time demonstrated better fretting wear resistance, which we attribute to higher microhardness of the surface layer. The coefficient of friction and wear volume of specimens at each different displacement amplitude significantly decreased with increasing milling time. As the displacement amplitude increased, the three fretting states were: partial slip coordinated by elastic deformation; partial slip state coordinated by plastic deformation; and gross slip condition. Our observations indicate that mechanical ball milling could be an efficient approach to improve the fretting wear resistance of GCr15 steel balls.
Open AccessThe Effect of the Displacement Amplitude on the Fretting Wear of GCr15 Steel with a TiC Coating
In the present paper, the effect of mechanical ball milling time on the fretting wear of GCr15 steel balls at different displacement amplitudes is investigated. TiC powder coating was fabricated on the surface of GCr15 steel balls using various process times, and the fretting wear tests were conducted on an AISI 52100 steel disk with the applied force of 80 N. Additionally, various displacement amplitudes (10 μm, 20 μm, and 60 μm) were selected. Specimen attributes and wear scars were characterized using an inverted metallographic microscope, a microhardness tester, an X-ray diffractometry analyzer, a white light interferometer, and a scanning electron microscope. The results showed that thick and continuous coatings could be obtained at the milling time of 18 h. The specimens processed for a longer milling time demonstrated better fretting wear resistance, which we attribute to higher microhardness of the surface layer. The coefficient of friction and wear volume of specimens at each different displacement amplitude significantly decreased with increasing milling time. As the displacement amplitude increased, the three fretting states were: partial slip coordinated by elastic deformation; partial slip state coordinated by plastic deformation; and gross slip condition. Our observations indicate that mechanical ball milling could be an efficient approach to improve the fretting wear resistance of GCr15 steel balls.
- Open Access
- 22 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7360
Salt-Fog Corrosion Behavior of GCr15 Steels Treated by Ultrasonic Strengthening Grinding Process
In this paper, the corrosion resistance of four GCr15 steel samples has been investigated. Three samples were initially surface-treated by ultrasonic shot peening (USP), a dry ultrasonic strengthening grinding process (DUSGP), and a wet ultrasonic strengthening grinding process (WUSGP), respectively, while another one was only polished. Then, all the processed samples were subjected to salt spray corrosion. Sample properties, such as capacitance arc, self-corrosion potential (Ecorr), self-corrosion current density (Icorr), corrosion morphology, and corrosion products were analyzed. Results show that the sample treated by WUSGP has the best corrosion resistance, which can be attributed to the high dislocation density, small grain size, needle-like and lath-like shape of martensite content formed in the treatment, which hinders Cl− from eroding the matrix. The obtained corrosion pits and cracks in Sample WUSGP show a width of approximately 1.4 µm and 2.1 µm, respectively, degrading 78% and 75% compared to polishing. The possible corrosion mechanism of the samples has been discussed. The findings denote that the treatment fused ceramic balls, strengthened liquid, and corundum in USP could be an efficient method to improve the corrosion resistance of some mechanical parts.
- 22 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7360
Open AccessSalt-Fog Corrosion Behavior of GCr15 Steels Treated by Ultrasonic Strengthening Grinding Process
In this paper, the corrosion resistance of four GCr15 steel samples has been investigated. Three samples were initially surface-treated by ultrasonic shot peening (USP), a dry ultrasonic strengthening grinding process (DUSGP), and a wet ultrasonic strengthening grinding process (WUSGP), respectively, while another one was only polished. Then, all the processed samples were subjected to salt spray corrosion. Sample properties, such as capacitance arc, self-corrosion potential (Ecorr), self-corrosion current density (Icorr), corrosion morphology, and corrosion products were analyzed. Results show that the sample treated by WUSGP has the best corrosion resistance, which can be attributed to the high dislocation density, small grain size, needle-like and lath-like shape of martensite content formed in the treatment, which hinders Cl− from eroding the matrix. The obtained corrosion pits and cracks in Sample WUSGP show a width of approximately 1.4 µm and 2.1 µm, respectively, degrading 78% and 75% compared to polishing. The possible corrosion mechanism of the samples has been discussed. The findings denote that the treatment fused ceramic balls, strengthened liquid, and corundum in USP could be an efficient method to improve the corrosion resistance of some mechanical parts.
- Open Access
Micromorphology, Microstructure, and Wear Behavior of AISI 1045 Steels Irregular Texture Fabricated by Ultrasonic Strengthening Grinding Process
In this study, the tribological properties of three AISI 1045 steel samples were investigated. Two samples were treated with ultrasonic shot peening (USP) and ultrasonic strengthening grinding process (USGP), respectively, while the other one was only treated with a polishing process. Sample properties, such as surface morphology, roughness, microhardness, elastic modulus, frictional coefficient, and phase structures were analyzed. Results show that the sample treated with USGP had the best tribological properties. It realized the highest surface roughness, microhardness, and elastic modulus. Compared with a polished sample, the roughness of the sample treated with USGP increased by 157%, and the microhardness and elastic modulus improved by 32.8% and 21.3%, respectively. Additionally, USGP provided an average frictional coefficient of 0.4, decreasing approximately 45% compared to polishing. The possible mechanisms of USGP surface texturing were discussed. The findings denote that USGP could be an efficient approach to improve the fatigue life of some mechanical components.
Open AccessMicromorphology, Microstructure, and Wear Behavior of AISI 1045 Steels Irregular Texture Fabricated by Ultrasonic Strengthening Grinding Process
In this study, the tribological properties of three AISI 1045 steel samples were investigated. Two samples were treated with ultrasonic shot peening (USP) and ultrasonic strengthening grinding process (USGP), respectively, while the other one was only treated with a polishing process. Sample properties, such as surface morphology, roughness, microhardness, elastic modulus, frictional coefficient, and phase structures were analyzed. Results show that the sample treated with USGP had the best tribological properties. It realized the highest surface roughness, microhardness, and elastic modulus. Compared with a polished sample, the roughness of the sample treated with USGP increased by 157%, and the microhardness and elastic modulus improved by 32.8% and 21.3%, respectively. Additionally, USGP provided an average frictional coefficient of 0.4, decreasing approximately 45% compared to polishing. The possible mechanisms of USGP surface texturing were discussed. The findings denote that USGP could be an efficient approach to improve the fatigue life of some mechanical components.