Abdelmoumene Laidouci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Abdelmoumene Laidouci has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Pratap Kumar Dakua
5 shared publicationsDeepak Kumar Panda
4 shared publicationsAbdelkader Aissat
Institut d'Electronique, de Microélectronique et de Nanotechnologie, UMR CNRS 8520, Universite des Sciences et Technologies de Lille 1,Avenue Poincaré CS 60069, Villeneuve d'Ascq,France,59652
3 shared publications- Abdelkader Aissat
LATSI Laboratory, University Blida1, Blida 09000, Algeria
3 shared publications Jean Pierre Vilcot
Institut d'Electronique, de Microélectronique et de Nanotechnologie, UMR CNRS 8520, Universite des Sciences et Technologies de Lille 1,Avenue Poincaré CS 60069, Villeneuve d'Ascq,France,59652
3 shared publicationsA. Aissat
Faculty of Technology, University of Blida.1, 09000 Blida, Algeria
2 shared publications
Latest Publications
- 11 July 2024
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 193
Optimization of efficiency of CZTS-based solar cell through exclusive BSF layer engineering method
- 11 July 2024
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 193
Optimization of efficiency of CZTS-based solar cell through exclusive BSF layer engineering method
- 13 February 2024
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (4) , 2015-2025
Evaluating CZTS Solar Cell Performance Based on Generation and Recombination Models for Possible ETLs Through Numerical Analysis
- 13 February 2024
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (4) , 2015-2025
Evaluating CZTS Solar Cell Performance Based on Generation and Recombination Models for Possible ETLs Through Numerical Analysis
- 15 December 2023
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 300
Improvement in the efficiency of solar cells based on the ZnSnN2/Si structure
- 15 December 2023
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 300
Improvement in the efficiency of solar cells based on the ZnSnN2/Si structure
- 12 November 2023
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 37 (2)
Simulation and numerical modeling of high‐efficiency CZTS solar cells with a BSF layer
The present paper deals with the photovoltaic performance‐based numerical evaluation of copper–zinc–tin–sulfur (CZTS) solar cells embedded with CZTSe as a back surface field (BSF) layer. CZTS has been considered a leading candidate for the fabrication of solar devices owing to its availability and absence of toxicity. Adding a BSF layer to a solar device is a novel way to boost efficiency. It reduces the recombination of the carriers at the back surface, thus increasing the overall current output of the solar cells. SCAPS 1D simulator is used to study the impact of several parameters on electrical properties like temperature, the thickness of the CZTS layer, acceptor doping concentration, and the impact of series and shunt resistances. Considering the optimized parameters in each layer of the solar cells, this work delivers 24.7% efficiency with the BSF layer, which is 8% more than that without the BSF layer. The results of this modeling will facilitate researchers to fabricate a highly efficient CZTS solar cell.
- 12 November 2023
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 37 (2)
Simulation and numerical modeling of high‐efficiency CZTS solar cells with a BSF layer
The present paper deals with the photovoltaic performance‐based numerical evaluation of copper–zinc–tin–sulfur (CZTS) solar cells embedded with CZTSe as a back surface field (BSF) layer. CZTS has been considered a leading candidate for the fabrication of solar devices owing to its availability and absence of toxicity. Adding a BSF layer to a solar device is a novel way to boost efficiency. It reduces the recombination of the carriers at the back surface, thus increasing the overall current output of the solar cells. SCAPS 1D simulator is used to study the impact of several parameters on electrical properties like temperature, the thickness of the CZTS layer, acceptor doping concentration, and the impact of series and shunt resistances. Considering the optimized parameters in each layer of the solar cells, this work delivers 24.7% efficiency with the BSF layer, which is 8% more than that without the BSF layer. The results of this modeling will facilitate researchers to fabricate a highly efficient CZTS solar cell.
- 27 October 2023
- Published by Elsevier in Micro and Nanostructures
- Vol. 184
Investigating the potential of earth-abundant ZnSnxGe1-xN2 alloys for quantum well solar cells
- 27 October 2023
- Published by Elsevier in Micro and Nanostructures
- Vol. 184
Investigating the potential of earth-abundant ZnSnxGe1-xN2 alloys for quantum well solar cells
- Open Access
Performance evaluation of ZnSnN2 solar cells with Si back surface field using SCAPS-1D: A theoretical study
- 7 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 67-70
Study on the impact of CuI as Hole Transport Layer (HTL) for CZTS-based Solar Cell
CZTS (copper zinc tin sulfide) is a promising candidate for solar cell applications. In this simulation-based work, the comparison of cell output variation is examined by considering the layer thickness as well as series and shunt resistances. When CuI is used as a hole transport layer (HTL), the Schottky barrier is reduced and efficiency is raised. The final optimized cell with CuI as the HT layer obtained a power conversion efficiency of 16.92%. The performance of the device was compared with and without HTL. The study’s findings pave the path for using CuI as an HTL for solar cell device production using CZTS.
- 7 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 67-70
Study on the impact of CuI as Hole Transport Layer (HTL) for CZTS-based Solar Cell
CZTS (copper zinc tin sulfide) is a promising candidate for solar cell applications. In this simulation-based work, the comparison of cell output variation is examined by considering the layer thickness as well as series and shunt resistances. When CuI is used as a hole transport layer (HTL), the Schottky barrier is reduced and efficiency is raised. The final optimized cell with CuI as the HT layer obtained a power conversion efficiency of 16.92%. The performance of the device was compared with and without HTL. The study’s findings pave the path for using CuI as an HTL for solar cell device production using CZTS.
- 1 November 2020
- Published by Elsevier in Solar Energy
- Vol. 211, 237-243
Numerical study of solar cells based on ZnSnN2 structure
- 1 November 2020
- Published by Elsevier in Solar Energy
- Vol. 211, 237-243
Numerical study of solar cells based on ZnSnN2 structure
- 15 August 2020
- Published by Springer Nature
- p. 211-222
Simulation and Optimization of Cds/ZnSnN2 Structure for Solar Cell Applications with SCAPS-1D Software
- 15 August 2020
- Published by Springer Nature
- p. 211-222
Simulation and Optimization of Cds/ZnSnN2 Structure for Solar Cell Applications with SCAPS-1D Software
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Temperature Effect on ZnGexSn1-xN2/GaN Multiwell Quantum Solar Cells
In this paper, $w$ e are interested in the simulation and modeling of ZnGe x Sn 1-x N 2 /GaN quantum wells (QWs) solar cell, according to many studies before the solar cells always are sensitive to the temperature, for this case, the effect of the temperature on photovoltaic characteristics such as power density-voltage P(V), current density-voltage I(V), and the external quantum efficiency EQE are investigated. The most parameter affected by the changing in the temperature is the open circuit voltage Voc. for optimization. It has been found at 280 K the cell gives better results of open circuit voltage and conversion efficiency their values are 2.18 V and 2.75% respectively.- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Temperature Effect on ZnGexSn1-xN2/GaN Multiwell Quantum Solar Cells
In this paper, $w$ e are interested in the simulation and modeling of ZnGe x Sn 1-x N 2 /GaN quantum wells (QWs) solar cell, according to many studies before the solar cells always are sensitive to the temperature, for this case, the effect of the temperature on photovoltaic characteristics such as power density-voltage P(V), current density-voltage I(V), and the external quantum efficiency EQE are investigated. The most parameter affected by the changing in the temperature is the open circuit voltage Voc. for optimization. It has been found at 280 K the cell gives better results of open circuit voltage and conversion efficiency their values are 2.18 V and 2.75% respectively.