Oleksandr Adamenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Oleksandr Adamenko has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Andriy Annenkov
Київський національний університет будівництва і архітектури
3 shared publications Олена Циколенко
Київський національний університет будівництва і архітектури
3 shared publicationsElena Tcikolenko
2 shared publications- Ivan Akolzin
Dnipro University of Technology
2 shared publications - Yurii Medvedskyi
Kyiv National University of Construction and Architecture
2 shared publications Юрій Медведський
Київський національний університет будівництва і архітектури
2 shared publications
Latest Publications
- Open Access
- 31 August 2026
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 4 (1(90)) , 63-69
Assessment of the distance effect on the registering spherical targets accuracy during terrestrial laser scanning
The object of research is the spherical targets used for point clouds registration and georeferencing. This research investigates the optimal distance between a terrestrial laser scanner (TLS) and spherical reference targets to achieve the required accuracy when determining their center coordinates. While TLS is highly effective for various geodetic tasks, formal operational guidelines remain underrepresented. To address this, the research analyzes the impact of scan density and the number of captured points on sphere approximation accuracy. Measurements were conducted using 145 mm diameter targets placed at distances from 3 to 24 meters. Data was acquired using FARO Focus S 150, Leica RTC360, and Trimble TX6 scanners. The point clouds were processed utilizing FARO Scene, Leica Cyclone Register 360, Trimble Real Works, and CloudCompare. An independent model based on the least squares method was used as a benchmark for assessing accuracy. The research establishes that a minimum of 200 points on a sphere's surface is essential for high-accuracy coordinate determination. Dropping below this threshold causes an approximate threefold deterioration in spatial accuracy. Evaluations showed varying software performance: CloudCompare can process as few as 5 points, and FARO Scene provides the highest accuracy with over 100 points, but Leica Cyclone software struggled with fewer than 50 points. Crucially, empirical analysis revealed that scanners register, on average, only 70% of the points that theoretically should fall on a target's surface. Based on these findings, this paper presents a practical reference table detailing optimal maximum scanner-to-target distances as a function of sphere diameter and scan density. These results provide vital guidance for the a priori planning of TLS projects, ensuring accurate scan registration and point cloud georeferencing.
- 31 August 2026
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 4 (1(90)) , 63-69
Open AccessAssessment of the distance effect on the registering spherical targets accuracy during terrestrial laser scanning
The object of research is the spherical targets used for point clouds registration and georeferencing. This research investigates the optimal distance between a terrestrial laser scanner (TLS) and spherical reference targets to achieve the required accuracy when determining their center coordinates. While TLS is highly effective for various geodetic tasks, formal operational guidelines remain underrepresented. To address this, the research analyzes the impact of scan density and the number of captured points on sphere approximation accuracy. Measurements were conducted using 145 mm diameter targets placed at distances from 3 to 24 meters. Data was acquired using FARO Focus S 150, Leica RTC360, and Trimble TX6 scanners. The point clouds were processed utilizing FARO Scene, Leica Cyclone Register 360, Trimble Real Works, and CloudCompare. An independent model based on the least squares method was used as a benchmark for assessing accuracy. The research establishes that a minimum of 200 points on a sphere's surface is essential for high-accuracy coordinate determination. Dropping below this threshold causes an approximate threefold deterioration in spatial accuracy. Evaluations showed varying software performance: CloudCompare can process as few as 5 points, and FARO Scene provides the highest accuracy with over 100 points, but Leica Cyclone software struggled with fewer than 50 points. Crucially, empirical analysis revealed that scanners register, on average, only 70% of the points that theoretically should fall on a target's surface. Based on these findings, this paper presents a practical reference table detailing optimal maximum scanner-to-target distances as a function of sphere diameter and scan density. These results provide vital guidance for the a priori planning of TLS projects, ensuring accurate scan registration and point cloud georeferencing.
- Open Access
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 22-30
ANALYSIS OF METHODS FOR CONTROLLING METROLOGICAL CHARACTERISTICS OF LASER TRACKERS
Laser trackers are pivotal components within contemporary measurement technology, offering unparalleled precision and reliability in measurement processes. Yet, maintaining their effectiveness mandates a systematic approach to controlling their metrological traits. Both static and dynamic research methodologies are routinely employed to evaluate the accuracy of laser trackers. This article embarks on a detailed exploration of the methodologies employed to regulate the metrological attributes of laser trackers, encompassing the utilization of length artifacts, network methodologies, control mechanisms utilizing rotary tables, and interferometry techniques. By delving into these methodologies, the article endeavors to establish a robust framework for evaluating the accuracy and reliability of laser trackers. This process stands as a critical juncture in guaranteeing their effectiveness across various measurement tasks. The meticulous analysis of these methods is instrumental in enhancing the precision and dependability of laser trackers, thereby bolstering their utility across diverse industrial and scientific domains. Consequently, efforts directed towards refining the metrological characteristics of laser trackers play an indispensable role in the continuous advancement of measurement technology. They facilitate the seamless integration of laser trackers into an array of applications, ensuring their efficacy and reliability in addressing complex measurement challenges encountered in modern industries and scientific research endeavors. Лазерні трекери є ключовими пристроями у сучасній вимірювальній техніці, забезпечуючи високу точність і надійність у вимірюваннях. Однак, забезпечення їхньої ефективності вимагає систематичного контролю їхніх метрологічних характеристик. Статичні та динамічні дослідження є загальноприйнятими методами для оцінки точності вимірювань лазерними трекерами. В цій статті виконується аналіз методів контролю метрологічних характеристик лазерних трекерів, зокрема застосування матеріальної міри, мережевого методу, контролю з використанням поворотного столу та інтерферометра.
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 22-30
Open AccessANALYSIS OF METHODS FOR CONTROLLING METROLOGICAL CHARACTERISTICS OF LASER TRACKERS
Laser trackers are pivotal components within contemporary measurement technology, offering unparalleled precision and reliability in measurement processes. Yet, maintaining their effectiveness mandates a systematic approach to controlling their metrological traits. Both static and dynamic research methodologies are routinely employed to evaluate the accuracy of laser trackers. This article embarks on a detailed exploration of the methodologies employed to regulate the metrological attributes of laser trackers, encompassing the utilization of length artifacts, network methodologies, control mechanisms utilizing rotary tables, and interferometry techniques. By delving into these methodologies, the article endeavors to establish a robust framework for evaluating the accuracy and reliability of laser trackers. This process stands as a critical juncture in guaranteeing their effectiveness across various measurement tasks. The meticulous analysis of these methods is instrumental in enhancing the precision and dependability of laser trackers, thereby bolstering their utility across diverse industrial and scientific domains. Consequently, efforts directed towards refining the metrological characteristics of laser trackers play an indispensable role in the continuous advancement of measurement technology. They facilitate the seamless integration of laser trackers into an array of applications, ensuring their efficacy and reliability in addressing complex measurement challenges encountered in modern industries and scientific research endeavors. Лазерні трекери є ключовими пристроями у сучасній вимірювальній техніці, забезпечуючи високу точність і надійність у вимірюваннях. Однак, забезпечення їхньої ефективності вимагає систематичного контролю їхніх метрологічних характеристик. Статичні та динамічні дослідження є загальноприйнятими методами для оцінки точності вимірювань лазерними трекерами. В цій статті виконується аналіз методів контролю метрологічних характеристик лазерних трекерів, зокрема застосування матеріальної міри, мережевого методу, контролю з використанням поворотного столу та інтерферометра.
- Open Access
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 391-404
PECULIARITIES OF UAV MAPPING OF THE TERRITORY WITH A SIGNIFICANT ELEVATION DIFFERENC
The research delves into a comprehensive analysis of the outcomes derived from Unmanned Aerial Vehicle (UAV) mapping applied to a terrain characterized by a significant variance in elevation. Specifically, the study focuses on the incline of the National Museum of the Holodomor Genocide in Kyiv. Throughout the process of generating orthophotomaps, meticulous attention was given to georeferencing the images to reference points. The coordinates of these points were determined with precision using Global Navigation Satellite System (GNSS) methods implemented through a network of permanent Real-Time Kinematic (RTK) stations. In addition to the georeferencing process, these points underwent coordination to facilitate a more in-depth analysis of linear distortions evident in the orthophotomap along and across the slope. Upon scrutinizing the results obtained by comparing horizontal distortions between control points derived from the orthophoto and those obtained through analytical calculations, a discernible correlation emerged between the elevation difference and the magnitude of misalignment. It was observed that longer lines parallel to the slope exhibited a tendency for increased errors, while no such dependence was noted for lines perpendicular to the slope. This observed trend underscores the importance of considering elevation differences in the survey area when employing UAV survey methodology. The results strongly suggest the feasibility and practicality of integrating such considerations into the UAV surveying process for terrains characterized by significant elevation variations.
- 29 March 2024
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 85,p. 391-404
Open AccessPECULIARITIES OF UAV MAPPING OF THE TERRITORY WITH A SIGNIFICANT ELEVATION DIFFERENC
The research delves into a comprehensive analysis of the outcomes derived from Unmanned Aerial Vehicle (UAV) mapping applied to a terrain characterized by a significant variance in elevation. Specifically, the study focuses on the incline of the National Museum of the Holodomor Genocide in Kyiv. Throughout the process of generating orthophotomaps, meticulous attention was given to georeferencing the images to reference points. The coordinates of these points were determined with precision using Global Navigation Satellite System (GNSS) methods implemented through a network of permanent Real-Time Kinematic (RTK) stations. In addition to the georeferencing process, these points underwent coordination to facilitate a more in-depth analysis of linear distortions evident in the orthophotomap along and across the slope. Upon scrutinizing the results obtained by comparing horizontal distortions between control points derived from the orthophoto and those obtained through analytical calculations, a discernible correlation emerged between the elevation difference and the magnitude of misalignment. It was observed that longer lines parallel to the slope exhibited a tendency for increased errors, while no such dependence was noted for lines perpendicular to the slope. This observed trend underscores the importance of considering elevation differences in the survey area when employing UAV survey methodology. The results strongly suggest the feasibility and practicality of integrating such considerations into the UAV surveying process for terrains characterized by significant elevation variations.
- Open Access
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 5,p. 240-257
INVESTIGATION OF THE ACCURACY OF DETERMINING THE COORDINATES OF SPHERES USING THE FARO FOCUS S 120 LASER SCANNER
Goal. The purpose of the work is research and analysis of the accuracy of determining the coordinates of spheres during geodetic work on laser scanning. Methods. The study of the accuracy of measurements of the laser scanner was carried out by the method of direct measurements. During the research, the reference value of the displacement of the sphere was measured using a laser interferometer. The measurements were performed to determine the measurement errors of various measured values of the laser scanner: horizontal angle, vertical angle and distance. Processing of scans and determination of sphere coordinates was carried out in the FARO Scene Lt software complex. Processing of measurement results was carried out by methods of mathematical statistics using MS Excel. Scientific novelty. A study of the sensitivity of the laser scanner for determining minor displacements of reference targets, using spheres as an example, was carried out. Work with sensitivity studies in determining the coordinates of reference targets, as a component of the error in determining their coordinates, we did not find. Practical significance. The conducted studies will allow determining the optimal ranges of location of reference targets during scanning to ensure the highest accuracy of determining their coordinates. However, it has been experimentally proven that this method cannot be used to determine the full accuracy characteristics of a laser scanner in determining the coordinates of reference targets, since the influence of some systematic errors, such as the eccentricity of the component parts of the laser scanner, is excluded in the measurements. The results. According to the research results, it is possible to draw a conclusion about the most appropriate location of reference targets in the form of spheres to achieve the highest accuracy of determining their coordinates. As can be seen from the research, it is desirable to place the spheres at a distance of approximately 5 m from the NLS. At shorter distances (about 2 m), the accuracy of determining the coordinates of the spheres begins to be affected by the growing errors of measuring distances by the scanner, at large distances (from 10 m), the errors of measuring the height coordinates of the spheres increase. The results presented in the paper require further research. These studies should be performed for other types of reference targets and with the use of other models of laser scanners, which is the goal of further research by the authors.
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 5,p. 240-257
Open AccessINVESTIGATION OF THE ACCURACY OF DETERMINING THE COORDINATES OF SPHERES USING THE FARO FOCUS S 120 LASER SCANNER
Goal. The purpose of the work is research and analysis of the accuracy of determining the coordinates of spheres during geodetic work on laser scanning. Methods. The study of the accuracy of measurements of the laser scanner was carried out by the method of direct measurements. During the research, the reference value of the displacement of the sphere was measured using a laser interferometer. The measurements were performed to determine the measurement errors of various measured values of the laser scanner: horizontal angle, vertical angle and distance. Processing of scans and determination of sphere coordinates was carried out in the FARO Scene Lt software complex. Processing of measurement results was carried out by methods of mathematical statistics using MS Excel. Scientific novelty. A study of the sensitivity of the laser scanner for determining minor displacements of reference targets, using spheres as an example, was carried out. Work with sensitivity studies in determining the coordinates of reference targets, as a component of the error in determining their coordinates, we did not find. Practical significance. The conducted studies will allow determining the optimal ranges of location of reference targets during scanning to ensure the highest accuracy of determining their coordinates. However, it has been experimentally proven that this method cannot be used to determine the full accuracy characteristics of a laser scanner in determining the coordinates of reference targets, since the influence of some systematic errors, such as the eccentricity of the component parts of the laser scanner, is excluded in the measurements. The results. According to the research results, it is possible to draw a conclusion about the most appropriate location of reference targets in the form of spheres to achieve the highest accuracy of determining their coordinates. As can be seen from the research, it is desirable to place the spheres at a distance of approximately 5 m from the NLS. At shorter distances (about 2 m), the accuracy of determining the coordinates of the spheres begins to be affected by the growing errors of measuring distances by the scanner, at large distances (from 10 m), the errors of measuring the height coordinates of the spheres increase. The results presented in the paper require further research. These studies should be performed for other types of reference targets and with the use of other models of laser scanners, which is the goal of further research by the authors.
- Open Access
- 17 June 2022
- Published by SE Ukrmetrteststandart in Measurements infrastructure
- No. 3
Application of proficiency testing scheme at determining the tank capacity on the results of laser 3D scanning
A three-level proficiency testing scheme is proposed in the form of the interlaboratory comparisons for the determination of the tank capacity of all possible types calculated by the laboratories’ own software. The proficiency testing scheme will be available to any accredited or non-accredited laboratory worldwide. Each laboratory chooses from the proposed computational tasks what it needs. To protect the confidentiality of the information within the framework of this scheme, all the Participants generate their individual codes, which they indicate in the file name with the results of their calculations. The laboratories are suggested to pass successfully three levels of operation characteristics testing ranked by the increase of the set tasks: 1) calculation of the tanks’ interval capacities without introducing any corrections by their 3D models prepared by the Provider; 2) calculation of the tanks' interval capacities by introducing all necessary corrections by their 3D models prepared by the Provider; 3) calculation of the tanks’ interval capacities by scans that have not been subjected to preliminary preparation by the Provider. To participate in the first level of the proficiency testing, it is necessary to: — download the program of proficiency testing of the first level from the site SE «Ukrmetrteststandart» https://metrology.kiev.ua/ru/mezhlaboratornye-sravneniya; — download files with point coordinates on the tank wall from Google disk Comparison: http://bit.ly/vgsucsm; — calculate interval capacities of the tanks without the introduction of any corrections; — send files with calibration tables of the tanks to the Provider’s e-mail: vgsucsm@gmail.com; — if the submitted data is suitable for analysis, then register and pay for the service; — receive the results of the proficiency testing via your e-mail; — read the publication of the proficiency testing results in the journal «Measurement infrastructure» https://mi-journal-online.org. At the first level of the proficiency testing, the payment is fulfilled only for the registration of the Participant and the execution of the documents on the completion of this level.
- 17 June 2022
- Published by SE Ukrmetrteststandart in Measurements infrastructure
- No. 3
Open AccessApplication of proficiency testing scheme at determining the tank capacity on the results of laser 3D scanning
A three-level proficiency testing scheme is proposed in the form of the interlaboratory comparisons for the determination of the tank capacity of all possible types calculated by the laboratories’ own software. The proficiency testing scheme will be available to any accredited or non-accredited laboratory worldwide. Each laboratory chooses from the proposed computational tasks what it needs. To protect the confidentiality of the information within the framework of this scheme, all the Participants generate their individual codes, which they indicate in the file name with the results of their calculations. The laboratories are suggested to pass successfully three levels of operation characteristics testing ranked by the increase of the set tasks: 1) calculation of the tanks’ interval capacities without introducing any corrections by their 3D models prepared by the Provider; 2) calculation of the tanks' interval capacities by introducing all necessary corrections by their 3D models prepared by the Provider; 3) calculation of the tanks’ interval capacities by scans that have not been subjected to preliminary preparation by the Provider. To participate in the first level of the proficiency testing, it is necessary to: — download the program of proficiency testing of the first level from the site SE «Ukrmetrteststandart» https://metrology.kiev.ua/ru/mezhlaboratornye-sravneniya; — download files with point coordinates on the tank wall from Google disk Comparison: http://bit.ly/vgsucsm; — calculate interval capacities of the tanks without the introduction of any corrections; — send files with calibration tables of the tanks to the Provider’s e-mail: vgsucsm@gmail.com; — if the submitted data is suitable for analysis, then register and pay for the service; — receive the results of the proficiency testing via your e-mail; — read the publication of the proficiency testing results in the journal «Measurement infrastructure» https://mi-journal-online.org. At the first level of the proficiency testing, the payment is fulfilled only for the registration of the Participant and the execution of the documents on the completion of this level.