Artem Igorevich Bogdanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Artem Igorevich Bogdanov has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Vitaliy Pavlovich Kulevich
Materials Science and Composite Materials Department, Volgograd State Technical University, 400005 Volgograd, Russia
21 shared publications - Victor Georgievich Shmorgun
Volgograd State Technical University
17 shared publications - Aleksandr Olegovich Taube
VNIKTInho
15 shared publications V G Shmorgun
Volgograd State Technical University, 28, Lenina ave., Volgograd, 400005, Russia
7 shared publications- Leonid Moiseevich Gurevich
Materials Science and Composite Materials Department, Volgograd State Technical University, 400005 Volgograd, Russia
6 shared publications - Victor Georgievich Shmorgun
Materials Science and Composite Materials Department, Volgograd State Technical University, 400005 Volgograd, Russia
6 shared publications
Latest Publications
- Open Access
- 1 August 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (8) , 274
Evaluation of Structural and Phase Stability of Multi-Component Heat-Resistant Coatings Based on Alloyed Iron and Nickel Aluminides
This study investigates the synthesis, phase evolution, and high-temperature oxidation behavior of multi-component aluminide coatings on EP670 (Fe-Ni base), EP718 (Ni-Fe base), and EP648 (Ni-base) superalloys. The coatings were produced using an economical hot-dip aluminizing method, followed by diffusion heat treatment at 1100 °C. In the as-deposited state, the coatings exhibit a heterogeneous structure consisting of an aluminum matrix with various Al-rich intermetallic inclusions. Subsequent heat treatment promotes the redistribution of chemical elements, leading to the elimination of free aluminum and the stabilization of a protective β-phase matrix. Long-term oxidation tests were performed at 900 °C, 1100 °C, and 1300 °C for up to 1000 h. At 1100 °C, the coatings on EP670 and EP648 demonstrated high stability, following a near-parabolic oxidation law and significantly reducing mass gain compared to uncoated substrates. However, at 1100 °C, the EP718 alloy underwent catastrophic failure within 200 h due to pest oxidation, disintegrating into an oxide powder—a phenomenon quantitatively confirmed by the kinetic exponent dropping below 1.0. At 1300 °C, the thermal limit for all coatings was established, with protective properties failing after 50 h. Based on the aluminum depletion kinetics, the service life at 1100 °C was estimated at 1300 h for EP670 and 2200 h for EP648. Scratch testing confirmed a complete absence of interfacial adhesive cracks across all systems. Contact loading triggered only cohesive cracks localized within the near-surface zone of the coatings. The results highlight the superior thermodynamic compatibility of the EP670 and EP648 systems with aluminide coatings, making them the most suitable candidates for extreme high-temperature applications.
- 1 August 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (8) , 274
Open AccessEvaluation of Structural and Phase Stability of Multi-Component Heat-Resistant Coatings Based on Alloyed Iron and Nickel Aluminides
This study investigates the synthesis, phase evolution, and high-temperature oxidation behavior of multi-component aluminide coatings on EP670 (Fe-Ni base), EP718 (Ni-Fe base), and EP648 (Ni-base) superalloys. The coatings were produced using an economical hot-dip aluminizing method, followed by diffusion heat treatment at 1100 °C. In the as-deposited state, the coatings exhibit a heterogeneous structure consisting of an aluminum matrix with various Al-rich intermetallic inclusions. Subsequent heat treatment promotes the redistribution of chemical elements, leading to the elimination of free aluminum and the stabilization of a protective β-phase matrix. Long-term oxidation tests were performed at 900 °C, 1100 °C, and 1300 °C for up to 1000 h. At 1100 °C, the coatings on EP670 and EP648 demonstrated high stability, following a near-parabolic oxidation law and significantly reducing mass gain compared to uncoated substrates. However, at 1100 °C, the EP718 alloy underwent catastrophic failure within 200 h due to pest oxidation, disintegrating into an oxide powder—a phenomenon quantitatively confirmed by the kinetic exponent dropping below 1.0. At 1300 °C, the thermal limit for all coatings was established, with protective properties failing after 50 h. Based on the aluminum depletion kinetics, the service life at 1100 °C was estimated at 1300 h for EP670 and 2200 h for EP648. Scratch testing confirmed a complete absence of interfacial adhesive cracks across all systems. Contact loading triggered only cohesive cracks localized within the near-surface zone of the coatings. The results highlight the superior thermodynamic compatibility of the EP670 and EP648 systems with aluminide coatings, making them the most suitable candidates for extreme high-temperature applications.
- 23 June 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 6(313)
BEHAVIOR OF INTERMETALLIC INTERLAYER IN A LAYERED COMPOSITE DURING ITS ROLLING
The results of a study on the rolling of a three-layer composite of St3 steel, AD1 aluminum, and VT1-0 titanium at temperatures exceeding the temperature threshold for intermetallic compound formation at the steel-aluminum interlayer boundary are presented. It is shown that the destruction of the diffusion zone at the steel-aluminum interlayer boundary during rolling is due to its high hardness, significantly exceeding the hardness of aluminum, titanium, and steel. This result demonstrates the impossibility of pressure treating layered composites with an intermetallic layer based on iron aluminides.
- 23 June 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 6(313)
BEHAVIOR OF INTERMETALLIC INTERLAYER IN A LAYERED COMPOSITE DURING ITS ROLLING
The results of a study on the rolling of a three-layer composite of St3 steel, AD1 aluminum, and VT1-0 titanium at temperatures exceeding the temperature threshold for intermetallic compound formation at the steel-aluminum interlayer boundary are presented. It is shown that the destruction of the diffusion zone at the steel-aluminum interlayer boundary during rolling is due to its high hardness, significantly exceeding the hardness of aluminum, titanium, and steel. This result demonstrates the impossibility of pressure treating layered composites with an intermetallic layer based on iron aluminides.
- Open Access
- 21 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 143
Formation of Ti-Cu-Ni Intermetallic Coatings on Titanium by Laser Processing of an Explosively Welded Layered Composite
This study investigates the influence of design factors and key process parameters—including explosive welding (EXW), rolling, and laser processing—on the formation, microstructure, and tribological properties of Ti–Cu–Ni intermetallic coatings. A combined manufacturing approach was employed, starting with the EXW of an MN19 cupronickel alloy to a VT1-0 titanium substrate, followed by multi-pass rolling to achieve a cladding thickness of approximately 0.3 mm. Subsequently, laser surface remelting was performed to facilitate controlled mass transfer and homogenization within the reaction zone. Numerical simulation using COMSOL Multiphysics v. 5.4 was utilized to optimize the thermal cycles and determine the ideal energy density (42 J/mm2) for phase formation. The results demonstrate that the primary structural components of the coatings produced under optimal conditions are solid solutions based on the ternary-modified titanium cuprides Ti2Cu(Ni) and TiCu(Ni). The transition from a layered bimetal to a finely dispersed intermetallic structure significantly enhances the surface characteristics. This specific phase composition provides a sustained microhardness of ~5 GPa across the coating cross-section. Comparative wear tests against fixed abrasive revealed that the wear resistance of the Ti–Cu–Ni coatings is 2.5 times higher at room temperature and 1.5 times higher at 600 °C than that of the base VT1-0 titanium.
- 21 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 143
Open AccessFormation of Ti-Cu-Ni Intermetallic Coatings on Titanium by Laser Processing of an Explosively Welded Layered Composite
This study investigates the influence of design factors and key process parameters—including explosive welding (EXW), rolling, and laser processing—on the formation, microstructure, and tribological properties of Ti–Cu–Ni intermetallic coatings. A combined manufacturing approach was employed, starting with the EXW of an MN19 cupronickel alloy to a VT1-0 titanium substrate, followed by multi-pass rolling to achieve a cladding thickness of approximately 0.3 mm. Subsequently, laser surface remelting was performed to facilitate controlled mass transfer and homogenization within the reaction zone. Numerical simulation using COMSOL Multiphysics v. 5.4 was utilized to optimize the thermal cycles and determine the ideal energy density (42 J/mm2) for phase formation. The results demonstrate that the primary structural components of the coatings produced under optimal conditions are solid solutions based on the ternary-modified titanium cuprides Ti2Cu(Ni) and TiCu(Ni). The transition from a layered bimetal to a finely dispersed intermetallic structure significantly enhances the surface characteristics. This specific phase composition provides a sustained microhardness of ~5 GPa across the coating cross-section. Comparative wear tests against fixed abrasive revealed that the wear resistance of the Ti–Cu–Ni coatings is 2.5 times higher at room temperature and 1.5 times higher at 600 °C than that of the base VT1-0 titanium.
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1935-1946
Composition and structure of heat-resistant coatings based on nickel and iron aluminides
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1935-1946
Composition and structure of heat-resistant coatings based on nickel and iron aluminides
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
ALUMINIZING OF IRONAND NICKEL-BASED ALLOYS BY THERMAL DIFFUSION SATURATION FROM A POWDER MIXTURE
Thermal diffusion aluminizing of NP2, Cr20Ni80, Cr15Ni60, steel 20880, and Cr15Al5 alloys was conducted in a powder mixture. The phase composition of the aluminide coatings and the kinetics of their thickness change at 680°C were studied.
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
ALUMINIZING OF IRONAND NICKEL-BASED ALLOYS BY THERMAL DIFFUSION SATURATION FROM A POWDER MIXTURE
Thermal diffusion aluminizing of NP2, Cr20Ni80, Cr15Ni60, steel 20880, and Cr15Al5 alloys was conducted in a powder mixture. The phase composition of the aluminide coatings and the kinetics of their thickness change at 680°C were studied.
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
ESTIMATION OF WEAR-RESISTANCE OF AL-TI SYSTEMS COATINGS BY SCRATCH METHOD
The results of a study of the wear resistance of titanium aluminide coatings in the temperature range of 20-400 °C are presented. It is shown that the wear resistance of binary coatings exceeds that of VT1-0 titanium by 1.4 times.
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
ESTIMATION OF WEAR-RESISTANCE OF AL-TI SYSTEMS COATINGS BY SCRATCH METHOD
The results of a study of the wear resistance of titanium aluminide coatings in the temperature range of 20-400 °C are presented. It is shown that the wear resistance of binary coatings exceeds that of VT1-0 titanium by 1.4 times.
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
EVALUATION OF HEAT RESISTANCE OF ALUMINIDE COATINGS ON THE SURFACE OF TITANIUM ALLOYS
Titanium alloys were aluminized using the molten-melt method. The heat resistance of the resulting coatings was compared to that of titanium alloys based on the change in sample weight at 700-850 °C.
- 19 February 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 2(309)
EVALUATION OF HEAT RESISTANCE OF ALUMINIDE COATINGS ON THE SURFACE OF TITANIUM ALLOYS
Titanium alloys were aluminized using the molten-melt method. The heat resistance of the resulting coatings was compared to that of titanium alloys based on the change in sample weight at 700-850 °C.
- 27 October 2025
- Published by Springer Nature in Metallurgist
- Vol. 69 (7) , 1047-1055
Surface hardening of titanium with aluminides using a combined technology including explosion welding, pressure treatment, and heat treatment
- 27 October 2025
- Published by Springer Nature in Metallurgist
- Vol. 69 (7) , 1047-1055
Surface hardening of titanium with aluminides using a combined technology including explosion welding, pressure treatment, and heat treatment
- Open Access
- 21 July 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (7) , 379
Formation of Intermetallic Coatings on Titanium by Explosive Welding and Subsequent Heat Treatment of the Layered Metal Composite
An approach for the formation of intermetallic coatings on the titanium surface based on titanium aluminides is proposed. The approach involves producing a layered steel-aluminum-titanium metal composite via explosive welding, followed by heat treatment to form a diffusion zone at the steel–aluminum interface with a thickness of more than 30 μm, sufficient for the spontaneous separation of the steel layer. As a result, an aluminum layer approximately 0.3 mm thick remains on the titanium surface. Subsequent heating at temperatures of 700–850 °C, below the allotropic transformation temperature of titanium, results in the transformation of the aluminum layer into titanium aluminides. The formation of the intermetallic coating structure occurs as a result of the upward transportation of TiAl3 fragments separated from the reaction zone by circulating melt flows. With increasing heat treatment time, these fragments become separated by the Al2O3 oxide phase.
- 21 July 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (7) , 379
Open AccessFormation of Intermetallic Coatings on Titanium by Explosive Welding and Subsequent Heat Treatment of the Layered Metal Composite
An approach for the formation of intermetallic coatings on the titanium surface based on titanium aluminides is proposed. The approach involves producing a layered steel-aluminum-titanium metal composite via explosive welding, followed by heat treatment to form a diffusion zone at the steel–aluminum interface with a thickness of more than 30 μm, sufficient for the spontaneous separation of the steel layer. As a result, an aluminum layer approximately 0.3 mm thick remains on the titanium surface. Subsequent heating at temperatures of 700–850 °C, below the allotropic transformation temperature of titanium, results in the transformation of the aluminum layer into titanium aluminides. The formation of the intermetallic coating structure occurs as a result of the upward transportation of TiAl3 fragments separated from the reaction zone by circulating melt flows. With increasing heat treatment time, these fragments become separated by the Al2O3 oxide phase.