Rao Kuang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rao Kuang has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
Yijun Shen
School of Marine Science and Engineering, Hainan University, Haikou, China
7 shared publications- Guo Chen
State Key Laboratory of Marine Resources Utilization in South China Sea, Hainan University, Haikou, 570228, PR China
3 shared publications Wen Li
Mechanical and Electrical Engineering College, Hainan University, Haikou, China
3 shared publications- Bin Du
Key Laboratory of Solar Energy Science and Technology in Jiangsu Province, Institute of Energy and Environment, Southeast University, Nanjing 210096, China
2 shared publications Deran Fu
2 shared publicationsGuo Chen
Mechanical and Electrical Engineering College, Hainan University, Haikou, China
2 shared publications
Latest Publications
- Open Access
Machine Learning Improves Performance Prediction and Interpretation of Efficiency Influencing Factors of a Novel Basalt-Fiber-Bundle Thermal Flow-Reversal Reactor for Methane Recovery
Low-concentration methane emissions from mines can be recovered using different reactor designs. Here, different artificial intelligence network techniques were employed to predict thermal performance of a basalt-fiber-bundle thermal flow-reversal reactor and investigate the influence of input parameters. The Back Propagation (BP) model gave the best accuracy (R2 = 0.974 for outlet temperature, 0.967 for thermal efficiency), exceeding that of traditional Computational Fluid Dynamics (CFD) simulations. For the present design, when flow velocity exceeded 1.5 m/s, the outlet gas temperature shifted from rising to falling, explained by the heat transfer between the gas and the solid inside the flow channel. Increasing the length of the flow-reversal period in the high-temperature phase reduced the outlet temperature, e.g., an increase from 60 s to 200 s decreased the outlet temperature by 34.1 K. Increasing inlet methane concentration (e.g., from 0.3% to 0.8%) first showed a slight improvement in thermal efficiency but further increase accelerated the oxidation reaction rate inside the reactor, reducing the temperature difference between the solid and gas in the channel, which slowed the heat exchange process and resulted in a downward trend in efficiency. The results indicate that the reactor can handle a wide range of exhaust gas concentrations, being suitable to treat low-methane-concentration exhaust gas. The BP model helped to establish the theoretical basis for setting optimal parameters values for the operation of the proposed reactor.
Open AccessMachine Learning Improves Performance Prediction and Interpretation of Efficiency Influencing Factors of a Novel Basalt-Fiber-Bundle Thermal Flow-Reversal Reactor for Methane Recovery
Low-concentration methane emissions from mines can be recovered using different reactor designs. Here, different artificial intelligence network techniques were employed to predict thermal performance of a basalt-fiber-bundle thermal flow-reversal reactor and investigate the influence of input parameters. The Back Propagation (BP) model gave the best accuracy (R2 = 0.974 for outlet temperature, 0.967 for thermal efficiency), exceeding that of traditional Computational Fluid Dynamics (CFD) simulations. For the present design, when flow velocity exceeded 1.5 m/s, the outlet gas temperature shifted from rising to falling, explained by the heat transfer between the gas and the solid inside the flow channel. Increasing the length of the flow-reversal period in the high-temperature phase reduced the outlet temperature, e.g., an increase from 60 s to 200 s decreased the outlet temperature by 34.1 K. Increasing inlet methane concentration (e.g., from 0.3% to 0.8%) first showed a slight improvement in thermal efficiency but further increase accelerated the oxidation reaction rate inside the reactor, reducing the temperature difference between the solid and gas in the channel, which slowed the heat exchange process and resulted in a downward trend in efficiency. The results indicate that the reactor can handle a wide range of exhaust gas concentrations, being suitable to treat low-methane-concentration exhaust gas. The BP model helped to establish the theoretical basis for setting optimal parameters values for the operation of the proposed reactor.
- Open Access
- 11 December 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (24) , 10853
High-Temperature Mechanical Properties of Basalt Fibers: A Step Towards Fire-Safe Materials for Photovoltaic Applications
Amidst the urban energy transition towards clean and renewable energy, distributed photovoltaic (PV) systems are emerging as critical infrastructure. However, the evolution of PV rack and mount systems has lagged, particularly in addressing cost efficiency and fire safety This study focuses on the high-temperature mechanical properties of basalt fibers (BFs), a key component of basalt fiber-reinforced polymer (BFRP), to establish a foundational understanding for future BFRP applications. The experimental results demonstrate that basalt fibers retain approximately 150 MPa residual tensile strength at 600 °C (30–40% of room temperature strength of Q235B steel) and 94 MPa at 800 °C, outperforming steel under similar conditions. Furthermore, the decomposition of wetting agents and Fe2+ oxidation at 600 °C was observed to stabilize after 100 min, maintaining structural integrity. These findings validate the high-temperature performance of BF, paving the way for subsequent studies at the BFRP composite level, which will address structural optimization and fire-resistance strategies for PV rack and mount systems. This research provides a critical step toward improving the safety and sustainability of urban PV systems.
- 11 December 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (24) , 10853
Open AccessHigh-Temperature Mechanical Properties of Basalt Fibers: A Step Towards Fire-Safe Materials for Photovoltaic Applications
Amidst the urban energy transition towards clean and renewable energy, distributed photovoltaic (PV) systems are emerging as critical infrastructure. However, the evolution of PV rack and mount systems has lagged, particularly in addressing cost efficiency and fire safety This study focuses on the high-temperature mechanical properties of basalt fibers (BFs), a key component of basalt fiber-reinforced polymer (BFRP), to establish a foundational understanding for future BFRP applications. The experimental results demonstrate that basalt fibers retain approximately 150 MPa residual tensile strength at 600 °C (30–40% of room temperature strength of Q235B steel) and 94 MPa at 800 °C, outperforming steel under similar conditions. Furthermore, the decomposition of wetting agents and Fe2+ oxidation at 600 °C was observed to stabilize after 100 min, maintaining structural integrity. These findings validate the high-temperature performance of BF, paving the way for subsequent studies at the BFRP composite level, which will address structural optimization and fire-resistance strategies for PV rack and mount systems. This research provides a critical step toward improving the safety and sustainability of urban PV systems.
- Top Cited Papers
- 26 July 2024
- Published by Elsevier in Renewable Energy
- Vol. 232
Numerical study on efficiency and robustness of wave energy converter-power take-off system for compressed air energy storage
- 26 July 2024
- Published by Elsevier in Renewable Energy
- Vol. 232
Top Cited PapersNumerical study on efficiency and robustness of wave energy converter-power take-off system for compressed air energy storage
- Open Access
Feasibility analysis of coexistence between plantation and tower concentrating solar system
- 16 February 2023
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 39, 101717
Improving performance prediction of evacuated tube solar collector through convolutional neural network method
- 16 February 2023
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 39, 101717
Improving performance prediction of evacuated tube solar collector through convolutional neural network method
- 1 November 2022
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 14 (6) , 062701
Review of studies on enhancing thermal energy grade in the open ocean
Ocean thermal energy conversion is one of the important ways to utilize low-grade ocean thermal energy. The main reasons for its low economic feasibility include high cost, small temperature difference, low energy efficiency, and high consumption of deep-sea cold energy extraction pumps. Some new means to improve the thermal energy grade may be beneficial to improve the economic feasibility of ocean thermal energy conversion, desalination, and other systems. The research progress and analysis results of ways to obtain low-grade thermal energy in the ocean surface by using solar energy, offshore platform waste heat, compressed air storage waste heat, and other methods show that (1) after using solar energy or waste heat to raise sea water temperature, shallow seawater can be used as the cold source, which can reduce most of the pump consumption and expensive riser cost of lifting cold seawater. This way improves the net power generation efficiency more significantly than improving the circulation mode and working medium and also significantly improves the economic feasibility. (2) Exhaust waste heat from offshore platform diesel power generation and compressed air energy storage power generation systems can be used to obtain a larger temperature difference between cold and hot seawater and further improve the efficiency of thermal power generation. (3) The low density of solar energy flow at the sea level leads to the high cost of offshore platforms. Incorporating ocean thermal energy conversion systems into floating photovoltaic power generation, seawater desalination and other systems can reduce the cost of offshore platforms.
- 1 November 2022
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 14 (6) , 062701
Review of studies on enhancing thermal energy grade in the open ocean
Ocean thermal energy conversion is one of the important ways to utilize low-grade ocean thermal energy. The main reasons for its low economic feasibility include high cost, small temperature difference, low energy efficiency, and high consumption of deep-sea cold energy extraction pumps. Some new means to improve the thermal energy grade may be beneficial to improve the economic feasibility of ocean thermal energy conversion, desalination, and other systems. The research progress and analysis results of ways to obtain low-grade thermal energy in the ocean surface by using solar energy, offshore platform waste heat, compressed air storage waste heat, and other methods show that (1) after using solar energy or waste heat to raise sea water temperature, shallow seawater can be used as the cold source, which can reduce most of the pump consumption and expensive riser cost of lifting cold seawater. This way improves the net power generation efficiency more significantly than improving the circulation mode and working medium and also significantly improves the economic feasibility. (2) Exhaust waste heat from offshore platform diesel power generation and compressed air energy storage power generation systems can be used to obtain a larger temperature difference between cold and hot seawater and further improve the efficiency of thermal power generation. (3) The low density of solar energy flow at the sea level leads to the high cost of offshore platforms. Incorporating ocean thermal energy conversion systems into floating photovoltaic power generation, seawater desalination and other systems can reduce the cost of offshore platforms.
- Open Access
- 31 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14186
Feasibility Analysis of Creating Light Environment for Growing Containers with Marine Renewable Energy
Offshore renewable energy is essential to reduce carbon emissions in China. However, due to the lack of application scenarios, it is difficult to use renewable energy locally near offshore power plants. To find an application scenario for offshore renewable energy, a growing container is developed and combined with offshore renewable energy for food production. Small experimental containers were tested, and their light intensities were compared to simulation results. The light intensity range and uniformity of 20-foot containers were evaluated for some short-growth cycle crops. Adding side reflectors and using LED light beads improved the energy efficiency considerably. Side reflectors improved both the light intensity U and lighting uniformity u on the irradiated surface, but the improvement decreased with increased plant height. With a plant height of 0–25 cm, U increased by 57.4–16.6% and u by 13.1–8%, compared to the case without reflectors. Considering the energy consumption of lighting, air conditioning, and ventilation, the daily power consumption of growing containers was between 50 and 79 kWh; a 5 MW wind plant could support the operation of up to 294 growing containers. Growing containers can also tolerate short-term output fluctuations in renewable power production and they can be adapted to sizeable seasonal output fluctuations by reducing the proportion of leafy vegetables and increasing the proportion of sprouts and mushrooms, which require less light.
- 31 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14186
Open AccessFeasibility Analysis of Creating Light Environment for Growing Containers with Marine Renewable Energy
Offshore renewable energy is essential to reduce carbon emissions in China. However, due to the lack of application scenarios, it is difficult to use renewable energy locally near offshore power plants. To find an application scenario for offshore renewable energy, a growing container is developed and combined with offshore renewable energy for food production. Small experimental containers were tested, and their light intensities were compared to simulation results. The light intensity range and uniformity of 20-foot containers were evaluated for some short-growth cycle crops. Adding side reflectors and using LED light beads improved the energy efficiency considerably. Side reflectors improved both the light intensity U and lighting uniformity u on the irradiated surface, but the improvement decreased with increased plant height. With a plant height of 0–25 cm, U increased by 57.4–16.6% and u by 13.1–8%, compared to the case without reflectors. Considering the energy consumption of lighting, air conditioning, and ventilation, the daily power consumption of growing containers was between 50 and 79 kWh; a 5 MW wind plant could support the operation of up to 294 growing containers. Growing containers can also tolerate short-term output fluctuations in renewable power production and they can be adapted to sizeable seasonal output fluctuations by reducing the proportion of leafy vegetables and increasing the proportion of sprouts and mushrooms, which require less light.