GRGiselle Ramirez

Giselle Ramirez

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Giselle Ramirez has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Repetitive Thermal Shock Of WC-Co Cemented Carbides: Assessment Of Surface Integrity Changes By Means Of Spherical Indentation

    by Universitat Politècnica de Catalunya, Jianxin Dong, Saghar Fooladi Mahani, Ltd. Xiamen Tungsten Co., Chao Liu, X Wen, Bolu Liu, Luis Llanes, Giselle Ramirez, Universitat Politècnica de Catalunya - BarcelonaTech, et al.

    Sudden changes in temperature are recognized to be critical service-like conditions that may drive failure in cemented carbides tools and components. From a physical viewpoint, thermal shock damage in ceramic-metal composites, such as cemented carbides, is a complex phenomenon. On the one hand, it involves introduction of residual stresses at the surface, with respect to the bulk, that may induce cracking. On the other hand, there exist deformation incompatibilities between the constitutive phases. Within this context, a fine-grained WC-Co system is subjected to sudden temperature drops in water quenching from maximum value of 570 ºC to room temperature, during five cycles. The resulting surface integrity is then assessed by spherical indentation, combined with advanced microscopy characterization. It allowed to measure the onset and evolution of quasi-plastic deformation and ring cracking for the tested conditions. These results are finally used to evaluate brittleness index changes induced by multiple thermal shocks.

  • Open Access

    Surface Integrity of Pure AW-1370 and TiC-Reinforced Aluminum WAAM Wires Under Unidirectional Sliding Contact

    by Nuria Cuadrado, Giselle Ramirez, Alejandra Torres, J. Antonio Travieso-Rodriguez, Jordi Llumà, Geir Kvam-Langelandsvik, Ida Westermann, Montserrat Vilaseca

    Wire arc additive manufacturing (WAAM) demands aluminum feedstock with tightly controlled diameter and high surface integrity. Adding hard TiC nanoparticles is a viable route to enhance the mechanical response of Al wires, yet the associated increase in contact severity can accelerate the wear of wire processing tools, particularly cemented carbide dies. This study elucidates the unidirectional sliding interaction between a TiC reinforced Al WAAM wire, and a WC/Co die material containing 5 wt% Co, using a modified scratch testing configuration under dry and lubricated conditions. Two dominant mechanisms are identified: (i) aluminum adhesion on the die surface and (ii) third body abrasion arising from WC particle pull out, promoted by preferential degradation of the cobalt binder. The presence of TiC nanoparticles reduces both the extent of Al transfer and the intensity of third body abrasion, an effect that is further amplified by lubrication. Consistently, lubrication also diminishes surface defects on the wire after sliding. The results provide a mechanistic basis to balance wire strengthening with tool life and highlight practical levers—nanoparticle reinforcement and lubrication strategies—for mitigating die damage while preserving WAAM wire surface quality.

  • Wear Transition Mechanisms Of WC-Co Cemented Carbides During Sliding Contact Tests

    by Jianxin Dong, Tom Gamp, Ltd. Xiamen Tungsten Co., Chao Liu, Ltd. Xiamen Golden Egret Special Alloy Co., Liangliang Lin, China National R&D Center for Tungsten Technology, Xiao Wen, Saghar Fooladi-Mahani, Luis Llanes, et al.

    Cemented carbides exhibit excellent wear resistance and good combination of hardness and toughness. These tribomechanical properties make them attractive for a wide range of industrial applications, where sliding contact response becomes key for optimizing performance of tools and components. Extensive studies have been conducted on wear behaviour of cemented carbides using different testing methods. However, a fundamental analysis of the sliding contact damage in the early stages is still a pending task, which can be helpful to improve the microstructural design. The aim of this work was to analyse the failure evolution of WC-Co cemented carbide under mild wear conditions. In doing so, hardmetals with different cobalt content were evaluated using single and multi-scratching tests. Transition mechanisms from cracking patterns to detachment of carbides|binder particles were discerned. Quasi-plastic and brittle failure mechanisms were documented by means of SEM and confocal inspection of both top- and cross-section surfaces of residual tracks.

  • Open Access

    Exploring Post-Machining Alternatives Under Dry Conditions for Thin-Walled Additive Manufacturing Components Aided by Infrared Thermography

    by Eduard Garcia-Llamas, Giselle Ramirez, Miguel Fuentes, Eduard Vidales, Jaume Pujante

    Additive manufacturing (AM) techniques have transformed the production of parts and components with intricate geometries and customized designs, driving innovation in sustainable manufacturing practices. The additive manufacturing technology used in this work was selective laser melting (SLM), a process that uses laser energy to sinter powdered metals into solid structures. Among the various materials utilized in AM, Ti6Al4V titanium alloys are of particular interest due to their favorable mechanical properties, corrosion resistance, biocompatibility, and potential for reducing material waste. However, the machining of additively manufactured titanium parts presents challenges due to the material’s low conductivity, elastic modulus, and chemical affinity with cutting tools, which impact tool wear and surface finish quality. Milling, a commonly employed process for finishing titanium parts, often involves significant energy use and tool wear, highlighting the need for optimized and eco-conscious machining strategies. This study aims to establish correlations among four key aspects: (1) surface finish of machined Ti6Al4V AM parts, (2) cutting tool damage, (3) dry milling parameters including different cutting tools, and (4) variation of temperature at the contact surface of AM parts and tools using infrared thermography. By examining parameters such as feed per tooth (Fz), axial depth of cut (Ap), spindle trajectories (trochoidal, helicoidal, and linear), and cutting tool diameters, this work identifies conditions that enhance process efficiency while reducing environmental impact. Infrared thermography provides insights into temperature variations during milling, correlating these changes to surface roughness and critical machining parameters, thus contributing to the development of sustainable and high-performance manufacturing practices.


  • Open Access

    Wear Mechanisms in Press Hardening: An Analysis through Comparison of Tribological Tests and Industrial Tools

    by Jaume Pujante, Eduard Garcia-Llamas, Giselle Ramírez, Nuria Cuadrado, Agim Ademaj, Montserrat Vilaseca, Daniel Casellas

    Press hardened components have become widespread in the automotive industry in structural and crash-resistant applications, thanks to the combination of the complex shapes and high mechanical properties obtained. However, the press hardening of coated boron steel results in severe adhesive-based wear, with tool maintenance being required in as few as 3000 cycles. The current industrial implementation of press hardening is defined to work around this phenomenon. While this aspect has been studied by different authors, most of the literature deals with laboratory-scale tribosimulators, leaving an open question into how this knowledge transfers to macroscopic effects on the industrial process. In this work, wear in press hardening is studied by comparing the results obtained in laboratory conditions with a pilot-scale line, and finally, with wear mechanisms observed on industrial tools. The aim of this study is to consolidate the current knowledge about the micro-mechanisms involved, and to understand to what extent the existing tests reproduce the actual mechanisms observed in the press floor. The results show how material transfer mainly happens as an accumulation of dust compacted into initial defects on the tool surface. Moreover, this mechanism is effectively reproduced in laboratory tribosimulators and pilot environments, showing a similar morphology to wear on industrial tools. The work sheds light on the underlying causes of wear, and its potential mitigation strategies.


  • Open Access

    Super-Hard DLC Coatings as an Alternative to Polycrystalline Diamond for Cutting Tools: Predictive Analysis of Aluminium Alloy Surface Quality

    by Giselle Ramírez, Jose M. Gonzalez Castro, Jordi Orrit-Prat, Raül Bonet, Nuria Cuadrado, Montserrat Vilaseca, Lluís Carreras, Jaume Caro

    The use of lightweight materials, such as ultra-high-strength aluminium alloys, is in high demand in the automotive and aerospace industries where weight savings are critical. The tool materials used for high-speed cutting of these aluminium alloys are subjected to severe conditions that promote premature failure of cutting tools. The application of polycrystalline diamond (PCD) coatings provides cutting tools with increased mechanical and thermal fatigue resistance and improved tribological performance. Despite these good properties, their high cost remains a major limitation in this sector. Super-hard Diamond-Like Carbon (DLC) coatings offer a technologically and economically feasible alternative to PCD-coated tools for cutting and machining non-ferrous materials. In this paper, the machining performance of coated and un-coated hard metal inserts in the turning of 7075 aluminium alloy has been explored. The surface quality of machined parts, the cutting tool wear resistance and the vibrations generated during turning of un-coated, PCD and super-hard thin DLC coatings on tungsten carbide inserts were compared. The results obtained demonstrate that DLC coatings are a potentially interesting alternative to PCD coatings for machining ultra-high-strength aluminium alloys, where surface component finish is a key factor.


  • Fracture Toughness of Iron Boride Layers Obtained by Paste Boriding Process

    by G. Ramírez, Ivan Campos-Silva, Alexander S. Balankin

    The fracture toughness of the Fe2B phase was evaluated in this study. Formation of the Fe2B boride is carried out though paste boriding process applied on AISI 1045 steel surface. The treatment was carried out at temperatures of 1193, 1223 and 1273 K for 6 h using a 5 mm thick boron paste. A Vickers microhardness tester was used to generate microcracks at a load of 200g. The indentations were made across the thickness of the iron boride layer at four different distances from the substrate. The experimental results show that the critical stress intensity factor KIC for the Fe2B phase shows a potential law dependence on crack length; this contradicts the concepts of Linear Elastic Fracture Mechanics, which establish that the fracture toughness value is a constant of the material.