Guowei Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Guowei Zhu has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Chenyang Zhu
College of Geoscience and Surveying Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
3 shared publications - Lei Zhang
School of Geosciences and Surveying Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
3 shared publications - Yufei Gong
College of Geoscience and Surveying Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
3 shared publications Guixin Zhang
Department of Geophysics and Information, School of Geosciences and Surveying Engineering, China University of Mining and Technology-Beijing, Beijing, China
2 shared publications- Jiawei Song
College of Geoscience and Surveying Engineering, China University of Mining and Technology-Beijing, Beijing 100083, China
2 shared publications - Qi Li
College of Geoscience and Surveying Engineering, China University of Mining and Technology-Beijing, Beijing 100083, China
2 shared publications
Latest Publications
- 14 October 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Phase‐Field Modeling of Borehole‐Pressure‐Induced Fracture Propagation in Coal‐Rock Composites Considering Compressive‐Shear Failure and Interface Effects
Pressure‐induced fracture propagation in coal‐rock composites is strongly governed by in‐situ stress, material heterogeneity, and interlayer interfaces. This study develops a dual phase‐field model that incorporates tensile fracture, compressive‐shear failure, and coal‐rock interface diffusion. The model combines the Mohr–Coulomb criterion with a triple‐shear‐energy criterion and is validated against uniaxial compression tests on coal‐rock specimens containing pre‐existing flaws. Parametric simulations are performed to examine the effects of in‐situ stress difference, nominal borehole‐pressure loading, interface strength ratio, and its coupling with the coal‐rock strength ratio. Increasing stress difference suppresses branching and promotes a dominant crack confined within the coal seam. Stronger borehole‐wall loading enlarges the fracture initiation zone and improves fracture connectivity. Interface strength controls crack deflection and penetration, while its effect depends nonlinearly on the coal‐rock strength ratio. These results clarify fracture‐interface interaction mechanisms and provide mechanistic insights relevant to hydraulic‐fracturing design in heterogeneous coal‐rock reservoirs.
- 14 October 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Phase‐Field Modeling of Borehole‐Pressure‐Induced Fracture Propagation in Coal‐Rock Composites Considering Compressive‐Shear Failure and Interface Effects
Pressure‐induced fracture propagation in coal‐rock composites is strongly governed by in‐situ stress, material heterogeneity, and interlayer interfaces. This study develops a dual phase‐field model that incorporates tensile fracture, compressive‐shear failure, and coal‐rock interface diffusion. The model combines the Mohr–Coulomb criterion with a triple‐shear‐energy criterion and is validated against uniaxial compression tests on coal‐rock specimens containing pre‐existing flaws. Parametric simulations are performed to examine the effects of in‐situ stress difference, nominal borehole‐pressure loading, interface strength ratio, and its coupling with the coal‐rock strength ratio. Increasing stress difference suppresses branching and promotes a dominant crack confined within the coal seam. Stronger borehole‐wall loading enlarges the fracture initiation zone and improves fracture connectivity. Interface strength controls crack deflection and penetration, while its effect depends nonlinearly on the coal‐rock strength ratio. These results clarify fracture‐interface interaction mechanisms and provide mechanistic insights relevant to hydraulic‐fracturing design in heterogeneous coal‐rock reservoirs.
- Open Access
Detection and Localization of Excavation-Disturbance-Related Near-Field Microseismic Events During TBM Tunneling
Tunnel boring machine (TBM) excavation generates continuous mechanical vibration that can obscure weak, short-duration propagating responses related to structural-plane disturbance. This study develops a Signal-Constrained Activation Detection and Localization (SCADL) framework using continuous three-component geophone-array records. SCADL first constructs an adaptive multi-station consistency trigger from synthesized three-component envelopes and rejects non-propagating mechanical disturbances using coherence and polarization constraints. First arrivals are picked by fusing statistical abrupt-change, local onset-gradient, and polarization-variation evidence, and event locations are estimated using an ahead-of-face layered velocity model and relative correction of similar event pairs. A multi-evidence activation index then integrates spatial clustering, coupling with the face-disturbance zone, shear/compression energy ratio, temporal evolution, and event quality to identify high-confidence candidate structural-plane activation events. The workflow was evaluated using one 16 h continuous field monitoring record acquired from a single TBM monitoring section and manually reviewed reference sets comprising 286 propagating events, 136 high-confidence events for arrival-time evaluation, and 96 events for activation-assessment review. SCADL identified 263 valid propagating events, achieved an event-level F1-score of 0.88, reduced the median arrival-time picking error to 2.4 ms, constrained the localization residual to 2.9 ms, and compressed the corrected cluster thickness to 0.82 m. Among the detected events, 86 high-confidence candidate activation events formed two clusters spatially consistent with the F04 and F02 structural zones confirmed by post-excavation geological validation. These results support the feasibility of SCADL for single-section TBM monitoring.
Open AccessDetection and Localization of Excavation-Disturbance-Related Near-Field Microseismic Events During TBM Tunneling
Tunnel boring machine (TBM) excavation generates continuous mechanical vibration that can obscure weak, short-duration propagating responses related to structural-plane disturbance. This study develops a Signal-Constrained Activation Detection and Localization (SCADL) framework using continuous three-component geophone-array records. SCADL first constructs an adaptive multi-station consistency trigger from synthesized three-component envelopes and rejects non-propagating mechanical disturbances using coherence and polarization constraints. First arrivals are picked by fusing statistical abrupt-change, local onset-gradient, and polarization-variation evidence, and event locations are estimated using an ahead-of-face layered velocity model and relative correction of similar event pairs. A multi-evidence activation index then integrates spatial clustering, coupling with the face-disturbance zone, shear/compression energy ratio, temporal evolution, and event quality to identify high-confidence candidate structural-plane activation events. The workflow was evaluated using one 16 h continuous field monitoring record acquired from a single TBM monitoring section and manually reviewed reference sets comprising 286 propagating events, 136 high-confidence events for arrival-time evaluation, and 96 events for activation-assessment review. SCADL identified 263 valid propagating events, achieved an event-level F1-score of 0.88, reduced the median arrival-time picking error to 2.4 ms, constrained the localization residual to 2.9 ms, and compressed the corrected cluster thickness to 0.82 m. Among the detected events, 86 high-confidence candidate activation events formed two clusters spatially consistent with the F04 and F02 structural zones confirmed by post-excavation geological validation. These results support the feasibility of SCADL for single-section TBM monitoring.
- Open Access
A Wavefield-Domain Method for Refining Residual Timing Errors in Passive-Source Seismic Exploration
In passive-source seismic exploration, even after seismic instruments complete unified start-up acquisition and hardware synchronization, long-duration continuous records may still contain small residual timing errors, which in turn broaden cross-correlation peaks and degrade event-location results. To address this problem, this study proposes a wavefield-domain residual timing refinement method. The method uses stable noise windows and controlled artificial events in continuous records as constraints, and performs data-window preprocessing, reference cross-correlation function construction, pairwise residual lag estimation, confidence-weighted multi-station joint fusion, and smoothing-constrained fitting of a continuous correction curve to achieve a posterior refinement of residual timing errors after hardware synchronization. Fractional-delay interpolation is then used for waveform correction. Validation using a 60 min continuous record from a local six-station array shows that the proposed method can serve as an effective supplement to hardware synchronization, suppress residual timing errors, and improve the temporal consistency, waveform stackability, and interpretation reliability of passive-source seismic exploration data.
Open AccessA Wavefield-Domain Method for Refining Residual Timing Errors in Passive-Source Seismic Exploration
In passive-source seismic exploration, even after seismic instruments complete unified start-up acquisition and hardware synchronization, long-duration continuous records may still contain small residual timing errors, which in turn broaden cross-correlation peaks and degrade event-location results. To address this problem, this study proposes a wavefield-domain residual timing refinement method. The method uses stable noise windows and controlled artificial events in continuous records as constraints, and performs data-window preprocessing, reference cross-correlation function construction, pairwise residual lag estimation, confidence-weighted multi-station joint fusion, and smoothing-constrained fitting of a continuous correction curve to achieve a posterior refinement of residual timing errors after hardware synchronization. Fractional-delay interpolation is then used for waveform correction. Validation using a 60 min continuous record from a local six-station array shows that the proposed method can serve as an effective supplement to hardware synchronization, suppress residual timing errors, and improve the temporal consistency, waveform stackability, and interpretation reliability of passive-source seismic exploration data.
- Open Access
Adaptive Impulse Reconstruction of Seismic Signals Induced by TBM Drilling Noise via CEEMDAN-Assisted MDD Interferometry
Tunnel ahead prospecting is important for reducing construction risks associated with faults, fractured zones, and cavities ahead of the tunnel face, but controlled active-source surveys are often impractical during continuous TBM operation. TBM drilling-noise records provide persistent passive excitation; however, strong nonstationarity and narrowband tonal contamination can hinder stable retrieval of interpretable impulse-like responses. We propose an adaptive impulse reconstruction algorithm that couples CEEMDAN-based mode screening with MDD interferometry. CEEMDAN screening suppresses quasi-stationary tonal components while preserving coherent propagation-related wavefields, producing effective signals suitable for interferometric processing. The MDD stage is stabilized using band-limited inversion, phase-only whitening, and a multi-reference strategy. Numerical experiments with a 3D elastic tunnel model indicate that the proposed workflow yields a more compact and laterally coherent virtual-source gather than correlation-based baselines (CC and PHAT-CC) and single-reference deconvolution interferometry, supporting reflection-oriented interpretation beyond simple wavelet compression. Field measurements from an operating TBM tunnel, together with a hammer-impact benchmark, are consistent with the feasibility of the workflow under real tunneling conditions and with physically plausible moveout behavior in the reconstructed gathers.
Open AccessAdaptive Impulse Reconstruction of Seismic Signals Induced by TBM Drilling Noise via CEEMDAN-Assisted MDD Interferometry
Tunnel ahead prospecting is important for reducing construction risks associated with faults, fractured zones, and cavities ahead of the tunnel face, but controlled active-source surveys are often impractical during continuous TBM operation. TBM drilling-noise records provide persistent passive excitation; however, strong nonstationarity and narrowband tonal contamination can hinder stable retrieval of interpretable impulse-like responses. We propose an adaptive impulse reconstruction algorithm that couples CEEMDAN-based mode screening with MDD interferometry. CEEMDAN screening suppresses quasi-stationary tonal components while preserving coherent propagation-related wavefields, producing effective signals suitable for interferometric processing. The MDD stage is stabilized using band-limited inversion, phase-only whitening, and a multi-reference strategy. Numerical experiments with a 3D elastic tunnel model indicate that the proposed workflow yields a more compact and laterally coherent virtual-source gather than correlation-based baselines (CC and PHAT-CC) and single-reference deconvolution interferometry, supporting reflection-oriented interpretation beyond simple wavelet compression. Field measurements from an operating TBM tunnel, together with a hammer-impact benchmark, are consistent with the feasibility of the workflow under real tunneling conditions and with physically plausible moveout behavior in the reconstructed gathers.
- 16 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-14
Using Low-Frequency Multi-Offset Ground Penetrating Radar to Measure Thin Asphalt Layer: A Super-Resolution Analysis Algorithm
The thickness detection of thin asphalt layers helps evaluate the construction quality and daily maintenance of roads. However, the limitation of low-frequency ground penetrating radar (GPR) resolution, combined with the similarity of the thin asphalt layer’s dielectric constant, leads to an inaccurate estimation of the thickness of the thin asphalt layer. Therefore, to accurately measure the thickness of thin asphalt layers, this paper proposes a super-resolution analysis algorithm based on Weighted Fourier Transform and Relaxation (WRELAX), which overcomes the resolution limit of low-frequency GPR and enables the construction of super-resolution signals. The efficient data acquisition method of multi-offset GPR enables us to verify its effectiveness in both simulation and field data. In the simulation data, the relative error in the electromagnetic wave velocity is within 1.84 %, and the thickness error is less than 9.30 %. In the field data, the maximum relative thickness error is 6.62 %. The research shows that the algorithm can accurately measure the thickness of the thin asphalt layer and the velocity of the electromagnetic wave without changing the design of the low-frequency multi-offset GPR equipment and its observation system. This algorithm offers a novel approach to detecting road structures, which is crucial in ensuring road safety.
- 16 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-14
Using Low-Frequency Multi-Offset Ground Penetrating Radar to Measure Thin Asphalt Layer: A Super-Resolution Analysis Algorithm
The thickness detection of thin asphalt layers helps evaluate the construction quality and daily maintenance of roads. However, the limitation of low-frequency ground penetrating radar (GPR) resolution, combined with the similarity of the thin asphalt layer’s dielectric constant, leads to an inaccurate estimation of the thickness of the thin asphalt layer. Therefore, to accurately measure the thickness of thin asphalt layers, this paper proposes a super-resolution analysis algorithm based on Weighted Fourier Transform and Relaxation (WRELAX), which overcomes the resolution limit of low-frequency GPR and enables the construction of super-resolution signals. The efficient data acquisition method of multi-offset GPR enables us to verify its effectiveness in both simulation and field data. In the simulation data, the relative error in the electromagnetic wave velocity is within 1.84 %, and the thickness error is less than 9.30 %. In the field data, the maximum relative thickness error is 6.62 %. The research shows that the algorithm can accurately measure the thickness of the thin asphalt layer and the velocity of the electromagnetic wave without changing the design of the low-frequency multi-offset GPR equipment and its observation system. This algorithm offers a novel approach to detecting road structures, which is crucial in ensuring road safety.
- 7 March 2025
- Published by Springer Nature in Acta Geophysica
- Vol. 73 (4) , 3339-3358
Acoustic impedance inversion using anisotropic total variation with structure-guidance and smoothly clipped absolute deviation penalty
- 7 March 2025
- Published by Springer Nature in Acta Geophysica
- Vol. 73 (4) , 3339-3358
Acoustic impedance inversion using anisotropic total variation with structure-guidance and smoothly clipped absolute deviation penalty
- Open Access
- 8 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (12) , 5012
Accurate Delimitation of Mine Goaves Using Multi-Attribute Comprehensive Identification and Data Fusion Technologies in 3D Seismic Exploration
Existing goaves (e.g., shafts and roadways) in mines represent important hidden dangers during the production of underlying coal seams. In this view, the accurate identification, analysis, and delimitation of the scope of goaves have become important in the 3D seismic exploration of mines. In particular, an accurate identification of the boundary swing position of goaves for 3D seismic data volumes within a certain depth interval is key and difficult at the same time. Here, a wide-band and wide-azimuth observation system was used to obtain high-resolution 3D seismic data. The complex structure of a mine was analyzed, and a seismic double processing system was applied to verify the fine processing effect of a goaf and improve the resolution of the 3D seismic data. Based on the seismic attribute identification characteristics of the goaf structure, we decided to adopt multi-attribute comprehensive identification and data fusion technologies to accurately determine the position of the goaf and of its boundary. Combining this information with the mine roadway engineering layout, we verified the accurateness and correctness of the goaf boundary location. Our study provides a good example of the accurate identification of the 3D seismic data of a roadway goaf.
- 8 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (12) , 5012
Open AccessAccurate Delimitation of Mine Goaves Using Multi-Attribute Comprehensive Identification and Data Fusion Technologies in 3D Seismic Exploration
Existing goaves (e.g., shafts and roadways) in mines represent important hidden dangers during the production of underlying coal seams. In this view, the accurate identification, analysis, and delimitation of the scope of goaves have become important in the 3D seismic exploration of mines. In particular, an accurate identification of the boundary swing position of goaves for 3D seismic data volumes within a certain depth interval is key and difficult at the same time. Here, a wide-band and wide-azimuth observation system was used to obtain high-resolution 3D seismic data. The complex structure of a mine was analyzed, and a seismic double processing system was applied to verify the fine processing effect of a goaf and improve the resolution of the 3D seismic data. Based on the seismic attribute identification characteristics of the goaf structure, we decided to adopt multi-attribute comprehensive identification and data fusion technologies to accurately determine the position of the goaf and of its boundary. Combining this information with the mine roadway engineering layout, we verified the accurateness and correctness of the goaf boundary location. Our study provides a good example of the accurate identification of the 3D seismic data of a roadway goaf.
- Open Access
Research on the Monitoring of Overlying Aquifer Water Richness in Coal Mining by the Time-Lapse Electrical Method
To study the influence of coal mining on the water richness overlying strata in the mining area using time-lapse electrical monitoring technology, four dataset acquisitions were completed with the same acquisition method, equipment, parameters, and processing flow. According to the characteristics of the data, major problems such as topographic correction, high-precision denoising, spatial and temporal normalization, and resistivity data inversion have been solved. Precise tomographic imaging was achieved through high-precision data processing and difference inversion. The results show that the electrical stratification characteristics of the overlying soil and rock layers are clear, the resistivity from the surface down gradually increases, and the electrical layers are not uniform locally. During mining, the overlying strata are affected by mining, the electrical resistivity of the underlying aquifers increased to varying degrees, and the fluctuation of electrical resistivity increased while the aquifer’s water content decreased. After mining, the overlying aquifer has the phenomenon of ‘reduced resistivity and water recovery’. After a period of time, the overlying soil disturbance and overlying rock failure zone will gradually tend to be stable. Meanwhile, the aquifer structure and water content will also gradually recover. Our results could provide guidance for water resources protection in this region.
Open AccessResearch on the Monitoring of Overlying Aquifer Water Richness in Coal Mining by the Time-Lapse Electrical Method
To study the influence of coal mining on the water richness overlying strata in the mining area using time-lapse electrical monitoring technology, four dataset acquisitions were completed with the same acquisition method, equipment, parameters, and processing flow. According to the characteristics of the data, major problems such as topographic correction, high-precision denoising, spatial and temporal normalization, and resistivity data inversion have been solved. Precise tomographic imaging was achieved through high-precision data processing and difference inversion. The results show that the electrical stratification characteristics of the overlying soil and rock layers are clear, the resistivity from the surface down gradually increases, and the electrical layers are not uniform locally. During mining, the overlying strata are affected by mining, the electrical resistivity of the underlying aquifers increased to varying degrees, and the fluctuation of electrical resistivity increased while the aquifer’s water content decreased. After mining, the overlying aquifer has the phenomenon of ‘reduced resistivity and water recovery’. After a period of time, the overlying soil disturbance and overlying rock failure zone will gradually tend to be stable. Meanwhile, the aquifer structure and water content will also gradually recover. Our results could provide guidance for water resources protection in this region.
- 7 September 2023
- Published by Society of Exploration Geophysicists in Interpretation
- Vol. 12 (1) , B1-B15
Seismic fault identification in coal mines based on the self-organizing map-gray wolf optimizer-support vector machine algorithm
Accurate fault identification in coal mines is important to improve mine safety and economic benefits. We compare various intelligent algorithms for data preprocessing and optimization and analyze the construction methods of seismic attribute data sets and the performance of intelligent optimization algorithms using fault identification accuracy as the discrimination index to find a better combined model for seismic fault identification. First, the training data set is constructed by mining the fault and nonfault information revealed by the roadway. The distribution characteristics of the seismic attribute data indicate similarities among them, and they are nonlinearly separable. Directly using the attributes to construct the data set, the accuracy of fault identification using the support vector machine (SVM) model is 78.41%. Principal component analysis (PCA) and self-organizing mapping (SOM) neural networks are used to extract effective information and then combined with the SVM classification model, and the accuracy of fault identification is 83.82% and 87.47%, respectively. Compared with the original data and PCA dimensionality reduction data, the accuracy of fault detection is improved by 9.06% and 3.66%, respectively, indicating that SOM can effectively improve the accuracy of fault detection by eliminating similar attributes and reducing the weight of redundant information. Then, through a fixed attribute data set, genetic algorithm (GA), particle swarm optimization (PSO), and gray wolf optimizer (GWO) intelligent optimization algorithms are used to find the optimal kernel function parameter and penalty parameter of the SVM classifier. The accuracy rate of the SOM-GWO-SVM model reaches 91.12%, compared with the SOM-PSO-SVM and SOM-GA-SVM, and the model accuracy is increased by 5.2% and 5.61%, respectively. Compared with PSO and GA, the GWO algorithm has a better global search ability. The identification result of the SOM-GWO-SVM model is closest to the actual fault exposure, especially for the identification of “short” faults and associated faults, which has obvious advantages over the traditional manual interpretation in terms of efficiency and accuracy.
- 7 September 2023
- Published by Society of Exploration Geophysicists in Interpretation
- Vol. 12 (1) , B1-B15
Seismic fault identification in coal mines based on the self-organizing map-gray wolf optimizer-support vector machine algorithm
Accurate fault identification in coal mines is important to improve mine safety and economic benefits. We compare various intelligent algorithms for data preprocessing and optimization and analyze the construction methods of seismic attribute data sets and the performance of intelligent optimization algorithms using fault identification accuracy as the discrimination index to find a better combined model for seismic fault identification. First, the training data set is constructed by mining the fault and nonfault information revealed by the roadway. The distribution characteristics of the seismic attribute data indicate similarities among them, and they are nonlinearly separable. Directly using the attributes to construct the data set, the accuracy of fault identification using the support vector machine (SVM) model is 78.41%. Principal component analysis (PCA) and self-organizing mapping (SOM) neural networks are used to extract effective information and then combined with the SVM classification model, and the accuracy of fault identification is 83.82% and 87.47%, respectively. Compared with the original data and PCA dimensionality reduction data, the accuracy of fault detection is improved by 9.06% and 3.66%, respectively, indicating that SOM can effectively improve the accuracy of fault detection by eliminating similar attributes and reducing the weight of redundant information. Then, through a fixed attribute data set, genetic algorithm (GA), particle swarm optimization (PSO), and gray wolf optimizer (GWO) intelligent optimization algorithms are used to find the optimal kernel function parameter and penalty parameter of the SVM classifier. The accuracy rate of the SOM-GWO-SVM model reaches 91.12%, compared with the SOM-PSO-SVM and SOM-GA-SVM, and the model accuracy is increased by 5.2% and 5.61%, respectively. Compared with PSO and GA, the GWO algorithm has a better global search ability. The identification result of the SOM-GWO-SVM model is closest to the actual fault exposure, especially for the identification of “short” faults and associated faults, which has obvious advantages over the traditional manual interpretation in terms of efficiency and accuracy.
- 1 March 2023
- Published by Springer Nature in Applied Geophysics
- Vol. 20 (1) , 116-129
Analysis of physical parameters of materials similar to coal and rock mass based on geophysical model construction of mines
- 1 March 2023
- Published by Springer Nature in Applied Geophysics
- Vol. 20 (1) , 116-129
Analysis of physical parameters of materials similar to coal and rock mass based on geophysical model construction of mines