Da Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Da Xu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Wenhui Cao
National Institute of Metrology, Beijing 100029, China
6 shared publications - Jinjin Li
Center for Advanced Measurement Science, National Institute of Metrology, Beijing, China
5 shared publications - Xueshen Wang
National Institute of Metrology, Beijing, China
5 shared publications - Qing Zhong
National Institute of Metrology (NIM), Beijing 100029, China
4 shared publications Jianting Zhao
National Institute of Metrology, Beijing, China
3 shared publicationsJinjin Li
National Institute of Metrology, Beijing, China
3 shared publications
Latest Publications
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-6
Design and Properties of SQUID Sensors With Octagonal Double Transformer for Cryogenic Current Comparator
Superconducting quantum interference devices (SQUIDs) with large input inductance and octagonal double transformer were designed and fabricated using Nb/Al-AlOx/Nb Josephson junctions for cryogenic current comparator. A 30-turn input coil of 1.5 μH is coupled to a large octagonal transformer of 3.6 nH, the counterpart of transformer is a 1.5-turn coil of 3.0 nH coupled to a second-order gradiometric SQUID of 97 pH. The octagonal double transformer makes low-inductance SQUID easily match to the large-inductance input coil. A current sensitivity of 1.1 μA/Φ0, a flux noise of 3.8 μΦ0/√Hz at 4 kHz and 9.7 μΦ0/√Hz at 1 Hz were achieved at 4.2 K. Another SQUID sensor with 10-turn input coil of 0.5 μH coupled to a large octagonal transformer of 6.0 nH, which is coupled to a first-order gradiometric SQUID of 580 pH, achieves a lower current sensitivity of 0.5 μA/Φ0 and a flux noise of 17 μΦ0/√Hz at 4 kHz.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-6
Design and Properties of SQUID Sensors With Octagonal Double Transformer for Cryogenic Current Comparator
Superconducting quantum interference devices (SQUIDs) with large input inductance and octagonal double transformer were designed and fabricated using Nb/Al-AlOx/Nb Josephson junctions for cryogenic current comparator. A 30-turn input coil of 1.5 μH is coupled to a large octagonal transformer of 3.6 nH, the counterpart of transformer is a 1.5-turn coil of 3.0 nH coupled to a second-order gradiometric SQUID of 97 pH. The octagonal double transformer makes low-inductance SQUID easily match to the large-inductance input coil. A current sensitivity of 1.1 μA/Φ0, a flux noise of 3.8 μΦ0/√Hz at 4 kHz and 9.7 μΦ0/√Hz at 1 Hz were achieved at 4.2 K. Another SQUID sensor with 10-turn input coil of 0.5 μH coupled to a large octagonal transformer of 6.0 nH, which is coupled to a first-order gradiometric SQUID of 580 pH, achieves a lower current sensitivity of 0.5 μA/Φ0 and a flux noise of 17 μΦ0/√Hz at 4 kHz.
- 4 July 2024
- Published by Springer Nature in Journal of Low Temperature Physics
- Vol. 216 (3-4) , 643-655
Cross-Coupling First-Order Gradient Superconducting Quantum Interference Device for Current Sensing
- 4 July 2024
- Published by Springer Nature in Journal of Low Temperature Physics
- Vol. 216 (3-4) , 643-655
Cross-Coupling First-Order Gradient Superconducting Quantum Interference Device for Current Sensing
- 24 August 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (10) , 105003
Optimization of Nb/Al-AlO x /Nb Josephson junctions through wafer-scale anodic oxidation: a systematic characterization and performance analysis
The Nb/Al-AlO x /Nb (SIS) Josephson junction is a crucial component in many types of superconducting devices. However, it can be easily damaged during the plasma fabrication processes. Anodic oxidation is an effective method for protecting SIS junctions by oxidizing Nb and Al from the junction profile. We used a custom wafer-scale anodic oxidation system and a neutral electrolyte to study the oxidation process of Nb films and Nb-Al(-AlO x )-Nb junctions. The oxidation process was thoroughly characterized by considering factors such as morphology and electrical properties. Anodization spectroscopy revealed varying oxidation sections from the top Nb layer to the bottom layer, extending across the Al-AlO x interlayer. This indicates that a 4 nm Al layer is sufficient to cover the surface of the bottom Nb film. High-resolution transmission electron microscopy and energy dispersive spectroscopy revealed that the Nb2O5 layer produced from the oxidation of the bottom Nb layer penetrated the Al2O3 layer and migrated to the top surface as the oxidation voltage increased. The top Nb layer of the SIS junction was also subjected to oxidation, despite the presence of a protective photoresist. Following the anodic oxidation process, the entire wafer surface was coated with an insulating Nb2O5 film. This film provided protection for the SIS junctions during the subsequent microfabrication process. The fabricated junction array, consisting of 128 junctions, demonstrated uniform electrical properties benefiting from the anodic oxidation process. This systematic analysis will further the research and practical applications of SIS junctions.
- 24 August 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (10) , 105003
Optimization of Nb/Al-AlO x /Nb Josephson junctions through wafer-scale anodic oxidation: a systematic characterization and performance analysis
The Nb/Al-AlO x /Nb (SIS) Josephson junction is a crucial component in many types of superconducting devices. However, it can be easily damaged during the plasma fabrication processes. Anodic oxidation is an effective method for protecting SIS junctions by oxidizing Nb and Al from the junction profile. We used a custom wafer-scale anodic oxidation system and a neutral electrolyte to study the oxidation process of Nb films and Nb-Al(-AlO x )-Nb junctions. The oxidation process was thoroughly characterized by considering factors such as morphology and electrical properties. Anodization spectroscopy revealed varying oxidation sections from the top Nb layer to the bottom layer, extending across the Al-AlO x interlayer. This indicates that a 4 nm Al layer is sufficient to cover the surface of the bottom Nb film. High-resolution transmission electron microscopy and energy dispersive spectroscopy revealed that the Nb2O5 layer produced from the oxidation of the bottom Nb layer penetrated the Al2O3 layer and migrated to the top surface as the oxidation voltage increased. The top Nb layer of the SIS junction was also subjected to oxidation, despite the presence of a protective photoresist. Following the anodic oxidation process, the entire wafer surface was coated with an insulating Nb2O5 film. This film provided protection for the SIS junctions during the subsequent microfabrication process. The fabricated junction array, consisting of 128 junctions, demonstrated uniform electrical properties benefiting from the anodic oxidation process. This systematic analysis will further the research and practical applications of SIS junctions.
- 27 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (9) , 1-5
Realization of a 2-V Programmable Josephson Junction Array Using Balanced Segmentation Scheme
This work proposes a balanced segmentation scheme to improve microwave transmission and develops a 2 V programmable Josephson junction array using double-stacked superconductor-normal-metal-superconductor Josephson junctions. The junction numbers of the sub-Josephson arrays are divided into a ternary sequence. The least significant bit is one stack or two junctions. In order to characterize the chip with many sub-arrays, an automatic measurement system with self-made multi-channel current sources was established. It can analyze the critical current, the margin of the voltage steps, and the number of junctions in each sub-array. The measurement found that the mentioned junction arrays can work at several microwave frequency ranges with an operating margin higher than 1.5 mA. Moreover, the circuit can produce intrinsically stable DC voltages from –2 V to +2 V and generate stepwise-approximated AC voltages.
- 27 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (9) , 1-5
Realization of a 2-V Programmable Josephson Junction Array Using Balanced Segmentation Scheme
This work proposes a balanced segmentation scheme to improve microwave transmission and develops a 2 V programmable Josephson junction array using double-stacked superconductor-normal-metal-superconductor Josephson junctions. The junction numbers of the sub-Josephson arrays are divided into a ternary sequence. The least significant bit is one stack or two junctions. In order to characterize the chip with many sub-arrays, an automatic measurement system with self-made multi-channel current sources was established. It can analyze the critical current, the margin of the voltage steps, and the number of junctions in each sub-array. The measurement found that the mentioned junction arrays can work at several microwave frequency ranges with an operating margin higher than 1.5 mA. Moreover, the circuit can produce intrinsically stable DC voltages from –2 V to +2 V and generate stepwise-approximated AC voltages.
- 30 June 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (8) , 085004
Low-noise second-order gradient SQUID current sensors overlap-coupled with input coils of different inductances
In this study, we developed a series of second-order gradient overlap-coupling octagonal superconducting quantum interference device (SQUID) current sensors for transition edge sensor (TES) applications. According to the requirements of TESs, we designed various parameters of SQUID current sensors, including different Josephson junction (JJ) sizes, different hysteresis and screening parameters, input coils with different inductances. The superconducting loop, input coil, and feedback coil of the SQUID current sensors adopt a second-order gradient structure, which can effectively enhance their anti-interference electromagnetic capability. Further, all the coupling structures between the superconducting loop and input/feedback coil adopt overlap-coupling octagonal structures, which can effectively enhance the coefficient of coupling mutual inductance. A series of second-order gradient SQUID current sensors overlap-coupled with input coils of 1.5, 2.5, and 5.5 turns based on Nb/Al–AlO x /Nb JJs were successfully fabricated on 2 inch silicon wafers by optimising the fabrication processes. From the simulation results, a minimal magnetic coupling factor of 0.02 between the feedback coil and input coil is obtained in the overlapped structure of the SQUID current sensor with an input coil of 1.5 turns; thus the magnetic interference between the feedback coil and input coil in this design is negligible. According to the measurement results at liquid–helium temperatures, SQUID current sensors with second-order gradient overlap-coupling octagonal structures have an excellent capability to weaken environmental electromagnetic interference. The SQUID current sensor with an input coil of 5.5 turns has the smallest current sensitivity, 2.4 μA/Φ0 and lowest current noise, 1 pA (√Hz)−1 compared with those of other input coils of different turns. The SQUID current sensor with an input coil of 2.5 turns has the lowest flux noise, 0.3 μΦ0 (√Hz)−1, and the lowest coupled noise energy, 11 h, among all the three different input coils, which are balanced results between the input inductance and the device noise. SQUID current sensors with second-order gradient overlap-coupling octagonal structures show low flux noise, low current noise, and low coupled noise energy, which can be compared with the state-of-art SQUID current sensor worldwide, and can satisfy the requirements of TES applications.
- 30 June 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (8) , 085004
Low-noise second-order gradient SQUID current sensors overlap-coupled with input coils of different inductances
In this study, we developed a series of second-order gradient overlap-coupling octagonal superconducting quantum interference device (SQUID) current sensors for transition edge sensor (TES) applications. According to the requirements of TESs, we designed various parameters of SQUID current sensors, including different Josephson junction (JJ) sizes, different hysteresis and screening parameters, input coils with different inductances. The superconducting loop, input coil, and feedback coil of the SQUID current sensors adopt a second-order gradient structure, which can effectively enhance their anti-interference electromagnetic capability. Further, all the coupling structures between the superconducting loop and input/feedback coil adopt overlap-coupling octagonal structures, which can effectively enhance the coefficient of coupling mutual inductance. A series of second-order gradient SQUID current sensors overlap-coupled with input coils of 1.5, 2.5, and 5.5 turns based on Nb/Al–AlO x /Nb JJs were successfully fabricated on 2 inch silicon wafers by optimising the fabrication processes. From the simulation results, a minimal magnetic coupling factor of 0.02 between the feedback coil and input coil is obtained in the overlapped structure of the SQUID current sensor with an input coil of 1.5 turns; thus the magnetic interference between the feedback coil and input coil in this design is negligible. According to the measurement results at liquid–helium temperatures, SQUID current sensors with second-order gradient overlap-coupling octagonal structures have an excellent capability to weaken environmental electromagnetic interference. The SQUID current sensor with an input coil of 5.5 turns has the smallest current sensitivity, 2.4 μA/Φ0 and lowest current noise, 1 pA (√Hz)−1 compared with those of other input coils of different turns. The SQUID current sensor with an input coil of 2.5 turns has the lowest flux noise, 0.3 μΦ0 (√Hz)−1, and the lowest coupled noise energy, 11 h, among all the three different input coils, which are balanced results between the input inductance and the device noise. SQUID current sensors with second-order gradient overlap-coupling octagonal structures show low flux noise, low current noise, and low coupled noise energy, which can be compared with the state-of-art SQUID current sensor worldwide, and can satisfy the requirements of TES applications.
- Open Access
Study of DC Magnetron Sputtered Nb Films
As Nb films are widely used as superconducting electrodes of Josephson junctions, it is important to investigate the properties of Nb films in order to fabricate high-quality Josephson junctions. In this work, we conducted a comprehensive analysis of the relationships among the properties of DC magnetron sputtered Nb films with a constant power fabricated at the National Institute of Metrology (China). The film properties, including superconductivity, stress, lattice constant, and surface roughness, were investigated. It was found that in the case of constant power and Ar pressure, the stress and other parameters of the Nb films can maintain a relatively stable state during the continuous consumption of the target material.
Open AccessStudy of DC Magnetron Sputtered Nb Films
As Nb films are widely used as superconducting electrodes of Josephson junctions, it is important to investigate the properties of Nb films in order to fabricate high-quality Josephson junctions. In this work, we conducted a comprehensive analysis of the relationships among the properties of DC magnetron sputtered Nb films with a constant power fabricated at the National Institute of Metrology (China). The film properties, including superconductivity, stress, lattice constant, and surface roughness, were investigated. It was found that in the case of constant power and Ar pressure, the stress and other parameters of the Nb films can maintain a relatively stable state during the continuous consumption of the target material.
- 1 January 2021
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 70 (12) , 128501-128501-8
A second-order gradiometric superconducting quantum interference device current sensor with cross-coupled structure
超导量子干涉仪(superconducting quantum interference Device, SQUID)具有极低的噪声水平, 极高的磁场灵敏度和电流灵敏度, 可探测低噪声传感器的微弱电流信号. SQUID电流传感器已成为超导转变边缘探测器(transition-edge sensor, TES)等低噪声探测信号读出的唯一选择. 本文研制了一种针对TES信号读出应用的二阶梯度交叉耦合SQUID电流传感器. 根据TES的信号读出需求, 设计了SQUID电流传感器的结构和各项参数. 其中, SQUID环路、输入线圈和反馈线圈均采用二阶梯度结构. SQUID环路与输入线圈、反馈线圈均采用不同平面交叉耦合方式, 可有效地减弱寄生电容. 通过优化工艺, 成功地研制出基于Nb/Al-AlOx/Nb约瑟夫森结的二阶梯度交叉耦合SQUID电流传感器. 液氦温区测试结果显示, 输入线圈电流灵敏度为17 μA/Φ0, 磁通白噪声为2 μΦ0/\begin{document}$ \sqrt{{\rm{H}}{\rm{z}}} $\end{document} , 电流白噪声为34 pA/\begin{document}$ \sqrt{{\rm{H}}{\rm{z}}} $\end{document} . 在无磁屏蔽条件下的噪声测试结果显示, 二阶梯度交叉耦合SQUID电流传感器具有良好的抵抗环境电磁干扰能力.- 1 January 2021
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 70 (12) , 128501-128501-8
A second-order gradiometric superconducting quantum interference device current sensor with cross-coupled structure
超导量子干涉仪(superconducting quantum interference Device, SQUID)具有极低的噪声水平, 极高的磁场灵敏度和电流灵敏度, 可探测低噪声传感器的微弱电流信号. SQUID电流传感器已成为超导转变边缘探测器(transition-edge sensor, TES)等低噪声探测信号读出的唯一选择. 本文研制了一种针对TES信号读出应用的二阶梯度交叉耦合SQUID电流传感器. 根据TES的信号读出需求, 设计了SQUID电流传感器的结构和各项参数. 其中, SQUID环路、输入线圈和反馈线圈均采用二阶梯度结构. SQUID环路与输入线圈、反馈线圈均采用不同平面交叉耦合方式, 可有效地减弱寄生电容. 通过优化工艺, 成功地研制出基于Nb/Al-AlOx/Nb约瑟夫森结的二阶梯度交叉耦合SQUID电流传感器. 液氦温区测试结果显示, 输入线圈电流灵敏度为17 μA/Φ0, 磁通白噪声为2 μΦ0/\begin{document}$ \sqrt{{\rm{H}}{\rm{z}}} $\end{document} , 电流白噪声为34 pA/\begin{document}$ \sqrt{{\rm{H}}{\rm{z}}} $\end{document} . 在无磁屏蔽条件下的噪声测试结果显示, 二阶梯度交叉耦合SQUID电流传感器具有良好的抵抗环境电磁干扰能力.