Olusegun Ayodeji Olagunju
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olusegun Ayodeji Olagunju has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Paul Musonge
Institute of Systems Science, Durban University of Technology, Durban 4001, South Africa; Faculty of Engineering, Mangosuthu University of Technology, Durban 4031, South Africa
2 shared publications - Chinedum Gloria Uzougbo
Delta State Ministry of Health, Asaba, Nigeria
1 shared publication - Chisom N. Onyebuchi
National Examinations Council, Nigeria
1 shared publication Chukuneye Neye-Akogo
Department of Systems Engineering, University of Lagos, Nigeria
1 shared publicationOgechi Amanda Onukogu
Department of Environmental Management, Federal University of Technology Owerri (FUTO), Nigeria
1 shared publication- Sammy Lewis Kiambi
Chemical Engineering Department, Vaal University of Technology, Vanderbilpark 1911, South Africa
1 shared publication
Latest Publications
- Open Access
- 5 January 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (4) , 15890-01e
Impacts of Industrial Wastewater Effluent on Ekerekana Creek and Policy Recommendations for Mitigation
This study investigated the impact of industrial wastewater originating from the Port-Harcourt Refinery Company Limited on Ekerekana Creek in Rivers State, serving as a primary fishing source for various communities. Water samples were collected and tested using established laboratory techniques, focusing on parameters such as heavy metals, pH levels, Phosphate, Nitrate, Temperature, Dissolved Oxygen, and BOD5. The findings revealed varying concentrations of heavy metals and other parameters in the water samples, with the highest concentrations observed at the discharge point (station 2), negatively affecting the flora population. The values of most parameters analyzed were below NESREA/WHO standards; however, the results underscore the importance of proper wastewater treatment and management from industrial sources to protect the environment and ensure the health and well-being of communities that rely on the creek.Based on the study's findings and best practices from the UK, US, and France, a set of comprehensive policy directions and community social responsibility measures are proposed. These recommendations include proper treatment of effluent by the Port-Harcourt Refinery Company Limited before discharge, active regulatory agency involvement, the adoption of an efficient and modern wastewater treatment facility, and the initiation of a clean-up procedure to reduce heavy metal concentrations and mitigate environmental hazards. Additionally, we advocate for the establishment of collaborative partnerships, community engagement, integrated watershed management, enforcement and compliance, research and innovation, and climate change adaptation and resilience measures. Implementing these recommendations will contribute to lasting improvements in water quality and the overall health of Ekerekana Creek and its surrounding communities.
- 5 January 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (4) , 15890-01e
Open AccessImpacts of Industrial Wastewater Effluent on Ekerekana Creek and Policy Recommendations for Mitigation
This study investigated the impact of industrial wastewater originating from the Port-Harcourt Refinery Company Limited on Ekerekana Creek in Rivers State, serving as a primary fishing source for various communities. Water samples were collected and tested using established laboratory techniques, focusing on parameters such as heavy metals, pH levels, Phosphate, Nitrate, Temperature, Dissolved Oxygen, and BOD5. The findings revealed varying concentrations of heavy metals and other parameters in the water samples, with the highest concentrations observed at the discharge point (station 2), negatively affecting the flora population. The values of most parameters analyzed were below NESREA/WHO standards; however, the results underscore the importance of proper wastewater treatment and management from industrial sources to protect the environment and ensure the health and well-being of communities that rely on the creek.Based on the study's findings and best practices from the UK, US, and France, a set of comprehensive policy directions and community social responsibility measures are proposed. These recommendations include proper treatment of effluent by the Port-Harcourt Refinery Company Limited before discharge, active regulatory agency involvement, the adoption of an efficient and modern wastewater treatment facility, and the initiation of a clean-up procedure to reduce heavy metal concentrations and mitigate environmental hazards. Additionally, we advocate for the establishment of collaborative partnerships, community engagement, integrated watershed management, enforcement and compliance, research and innovation, and climate change adaptation and resilience measures. Implementing these recommendations will contribute to lasting improvements in water quality and the overall health of Ekerekana Creek and its surrounding communities.
- Open Access
Production and Optimization of Biodiesel in a Membrane Reactor, Using a Solid Base Catalyst
The commercial Calcium oxide was successfully embedded on activated carbon surfaces to increase the reactive surface area of a composite catalyst material CaO/AC. The composite catalyst material was also successfully packed in the tubular titanium dioxide/Aluminum dioxide ceramic membrane reactor used to separate the biodiesel produced. Virgin soybean oil was used as precursor feedstock for the reaction. Using a central composite approach, response surface methodology (RSM) was employed to obtain the optimum conditions for producing biodiesel from soybean oil. A total of four process factors were examined (24 experimental designs). 30 experiments were derived and run to investigate the effects of temperature, reaction time, methanol to oil molar ratio, and catalyst concentration (calcium oxide attached on activated carbon). 96.9 percent of soybean oil methyl ester (SOME/biodiesel) was produced at 65 °C temperature, 90 min of reaction time, 4.2:1 molar ratio of methanol to oil, and 3.0 wt.% catalyst concentration. The measured yield and expected biodiesel production values were correlated in a linear sequence. The fuel qualities of SOME/biodiesel were tested, including kinematic viscosity, density, flash point, copper corrosion, calorific value, cloud point, pour point, ash content, and carbon residue.
Open AccessProduction and Optimization of Biodiesel in a Membrane Reactor, Using a Solid Base Catalyst
The commercial Calcium oxide was successfully embedded on activated carbon surfaces to increase the reactive surface area of a composite catalyst material CaO/AC. The composite catalyst material was also successfully packed in the tubular titanium dioxide/Aluminum dioxide ceramic membrane reactor used to separate the biodiesel produced. Virgin soybean oil was used as precursor feedstock for the reaction. Using a central composite approach, response surface methodology (RSM) was employed to obtain the optimum conditions for producing biodiesel from soybean oil. A total of four process factors were examined (24 experimental designs). 30 experiments were derived and run to investigate the effects of temperature, reaction time, methanol to oil molar ratio, and catalyst concentration (calcium oxide attached on activated carbon). 96.9 percent of soybean oil methyl ester (SOME/biodiesel) was produced at 65 °C temperature, 90 min of reaction time, 4.2:1 molar ratio of methanol to oil, and 3.0 wt.% catalyst concentration. The measured yield and expected biodiesel production values were correlated in a linear sequence. The fuel qualities of SOME/biodiesel were tested, including kinematic viscosity, density, flash point, copper corrosion, calorific value, cloud point, pour point, ash content, and carbon residue.
- Open Access
- 1 July 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 78 (1) , 012019
Production of Biodiesel Using a Membrane Reactor to Minimize Separation Cost
This study investigates the performance of a packed bed membrane reactor in the transesterification process of triglycerides to methyl ester using soyabean oil as feedstock. A TiO2/Al2O3 ceramic microporous membrane was selected due to its chemical inert nature and thermal stability to selectively remove the product from the reaction medium. CaO impregnated on the surface of activated carbon was packed into the membrane and acted as catalyst. The synthesized catalyst had a total loading of 40.50 % and was characterized by XRD and temperature-programmed desorption of CO2 (CO2-TPD). The crude biodiesel produced was micro-filtered by the ceramic membrane with a pore size of 0.02 μm to retain the unreacted oil and free glycerol, at the transmembrane pressure of 100 KPa. The best condition was achieved with a temperature of 65 °C, methanol/oil molar ratio of 6:1 for 150 minutes, which resulted in the highest FAME yield of 94 %. Methyl ester produced met the ASTM D6751 and SANS 1935 specifications. The product obtained was mainly composed of methyl esters. Glycerol was not detected in the product stream due to the ability of the membrane to retain the glycerol and the unreacted oil in the medium, which solved the issue of glycerol separation from biodiesel.
- 1 July 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 78 (1) , 012019
Open AccessProduction of Biodiesel Using a Membrane Reactor to Minimize Separation Cost
This study investigates the performance of a packed bed membrane reactor in the transesterification process of triglycerides to methyl ester using soyabean oil as feedstock. A TiO2/Al2O3 ceramic microporous membrane was selected due to its chemical inert nature and thermal stability to selectively remove the product from the reaction medium. CaO impregnated on the surface of activated carbon was packed into the membrane and acted as catalyst. The synthesized catalyst had a total loading of 40.50 % and was characterized by XRD and temperature-programmed desorption of CO2 (CO2-TPD). The crude biodiesel produced was micro-filtered by the ceramic membrane with a pore size of 0.02 μm to retain the unreacted oil and free glycerol, at the transmembrane pressure of 100 KPa. The best condition was achieved with a temperature of 65 °C, methanol/oil molar ratio of 6:1 for 150 minutes, which resulted in the highest FAME yield of 94 %. Methyl ester produced met the ASTM D6751 and SANS 1935 specifications. The product obtained was mainly composed of methyl esters. Glycerol was not detected in the product stream due to the ability of the membrane to retain the glycerol and the unreacted oil in the medium, which solved the issue of glycerol separation from biodiesel.