RLRuirong Liang

Ruirong Liang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ruirong Liang has a total of 136 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Spatiotemporal Characteristics of Type-I ELM Power Deposition Measured by Infrared Thermography on the EAST Tokamak

    by Tenghui Wang, Gaoting Chen, Youwen Sun, Qingquan Yang, Hua Yang, Manni Jia, Shaocheng Liu, Zhendong Yang, Qun Ma, Shuai Gu, et al.

    The spatiotemporal characteristics of natural and resonant magnetic perturbation (RMP)-mitigated type-I edge localized modes (ELMs) on EAST are investigated using a high-resolution infrared (IR) camera. Natural ELMs exhibit a rise time (τ_"rise" ) of 350–750 μs and a decay time (τ_decay) of 600–2300 μs, corresponding to τ_decay⁄τ_rise = 1.5–4. For RMP-mitigated ELMs, τ_"rise" and τ_decay are shorter than those of natural ELMs, which is correlated with a reduction in ELM size ((ΔW_ELM)/W_MHD ). Further analysis shows that, for both natural and RMP-mitigated ELMs, peak heat flux (q_peak) is largely independent of ELM size, whereas wetted area (A_wet) increases with ELM size. Moreover, RMP-mitigated ELMs exhibit slightly lower q_peak than natural ELMs, indicating a modest reduction in transient heat load even under weak mitigation. Comparison between measured peak energy fluence and Eich model predictions shows good agreement for both natural and RMP-mitigated ELMs, with a slightly lower peak energy fluence under RMP, likely due to reduced ELM size. These results suggest that RMP modulates both the temporal and spatial characteristics of ELMs on EAST, which could have implications for ELM control strategies.

  • Open Access

    Investigation of transient heat flux redistribution caused by rotating n = 2 RMP in ELM mitigation experiments on EAST

    by G.T. Chen, H. Yang, Y.W. Sun, M.N. Jia, Q. Ma, J.H. Yang, Q.Q. Yang, T.H. Wang, J.Z. Shi, Y.N. Zhang, et al.

    This study investigates the role of rotating n = 2 resonant magnetic perturbation (RMP) in modifying the transient heat flux distribution during edge localized mode (ELM) mitigation on Experimental Advanced Superconducting Tokamak. During ELM mitigation achieved by the application of a rotating n = 2 RMP, a pronounced reduction in the instantaneous peak heat flux is observed, with a slight increase in the time-averaged peak heat flux. Concurrently, strike point splitting appears in the ELM heat flux profiles, and the split strike points are found to rotate synchronously with the applied RMP field. The qualitative agreement in both the number and locations of strike points between TOP2D vacuum modeling and experimental results indicates that the strike point splitting in ELM heat flux profiles is affected by RMP. Furthermore, the broadening effect of RMP on the heat flux profile is quantified using the power decay length ( λ q ). During the mitigated-ELM phase, λ q increases to approximately 6.10 mm, compared to ∼2.86 mm during the inter-large-ELM phase and ∼4.86 mm during the intra-large-ELM phase without RMP. It indicates that the rotating n = 2 RMP significantly broadens the heat flux profiles and reduces the peak heat flux on the divertor target, which is beneficial for the safe operation of tokamaks.


  • Open Access

    Characteristic of the power decay length of small ELMs measured by infrared camera on EAST

    by G.T. Chen, Q.Q. Yang, J.H. Yang, X. Lin, H. Yang, Z.D. Yang, R.R. Liang, T.H. Wang, B.H. Zhang, L. Wang, et al.

    Small edge-localized-mode (ELM) regimes are being studied as promising solution to reduce the heat flux to the first-wall within tolerable levels in future machines. This study represents the first utilization of a high-resolution infrared camera system on the Experimental Advanced Superconducting Tokamak to investigate the heat flux characteristics of small ELMs. Both typical discharge results and statistical analyses indicate that the power decay length ( λ q ) of small ELMs is broader than that of inter-large ELMs but narrower than that of intra-large ELMs, consistent with previous simulations using the BOUT++ code. Further analysis indicates that low hybrid wave heating has a more significant impact on the λ q of small ELMs compared to other heating schemes. Among all the parameters, the line averaged density ( n el ) has the most notable effect on the heat flux width of small ELMs, as evidenced by both the correlation analysis and the result from typical shots. Furthermore, the investigation on the heat load deposition in far-scrape-off-layer (SOL) region during small ELMs shows that small ELMs under relatively low collisionality conditions, carrying less than 1% of the plasma stored energy, are found to deposit 0.2–0.45 of the ELM power to the far SOL region.


  • Open Access

    Towards detachment-compatible I-mode plasma on EAST tokamak

    by L. Yu, L. Wang, X.L. Zou, X. Lin, L.Y. Meng, Q.Q. Yang, X.M. Zhong, L.Q. Xu, A.D. Liu, R.R. Liang, et al.

    The divertor detachment is important for the improved confinement mode (I-mode) to serve as a reliable operating scenario in future fusion reactors. A reproducible steady-state I-mode operation with the energy detachment of the inner target has been achieved with the lower single-null configuration on the Experimental Advanced Superconducting Tokamak (EAST). Compared to the high confinement mode (H-mode), I-mode has a lower electron temperature on the inner divertor target and can achieve energy detachment at a lower density. In addition, dedicated experiments on neon (Ne) seeding to assist the exhaust of steady-state heat flux in I-mode discharges have also been successfully carried out on EAST. A significant reduction of the particle flux caused by the Ne impurity radiation was observed at both inner and outer divertor targets without I-L back-transition on EAST for the first time. This may be due to the ‘corner effect’ of the EAST right-angled divertor with a high divertor closure, which can effectively trap the impurity particles and thus reduce the influence of impurity on the main plasma. Furthermore, good core-edge compatibility was also obtained in the detached I-mode plasma with a radiative divertor. This study offers an attractive scenario of I-mode operation for avoiding excessively high transient and steady-state heat loads simultaneously in future fusion reactors.


  • Open Access

    Investigation of divertor heat flux characteristics under the influence of resonant magnetic perturbations on EAST

    by Ruirong Liang, Xianzu Gong, Bin Zhang, Manni Jia, Hua Yang, Qun Ma, Youwen Sun, Zhendong Yang, Yunchan Hu, Zuhao Wang, et al.

    Controlling the splitting divertor heat flux caused by resonant magnetic perturbations (RMPs) is a topic of concern for fusion devices. As a fundamental prerequisite, it is necessary to understand the characteristics of the heat flux distribution under the applied RMP field, which will be studied in this paper. The nonlinear phenomenon of strike point splitting was found to be strongly dependent on the plasma response under RMP. These splitting heat flux distributions are qualitatively explained by the simulated magnetic footprints. The RMP phase scanning experiment shows that scanning in a certain range of relative phase can maintain good edge-localized mode (ELM) mitigation and simultaneously sweep the striations of heat flux on divertor target. Additionally, even in upper single null (USN) configurations, heat stripes are observed on the lower outer divertor (LO-div), attributed to RMP-induced additional magnetic connections to the LO-div, as confirmed by magnetic topology simulations. A dedicated investigation into the impact of the discrepancy between lower and upper separatrix radii mapped to the low field side mid-plane ( d R sep ) reveals its significant influence on both ELM control and heat flux distribution. Within a certain range of d R sep , the heat flux distribution is improved while ELM suppression is maintained. These findings contribute to divertor heat flux understanding under RMP conditions in tokamak operations.


  • Open Access

    Experimental and modeling study of the impact of upstream D2 puff on divertor detachment and impurity control with argon seeding in EAST

    by Tao He, Zhongshi Yang, Kedong Li, Liang Wang, Guozhang Jia, Xiaoju Liu, Guojian Niu, Xin Lin, Feifei Nian, Rong Wang, et al.

    Radiative divertor is an effective method for the divertor heat flux control, but excessive core impurity radiation can deteriorate the confinement in tokamaks. In recent EAST experiments, the compatibility of divertor detachment and impurity control with good core confinement (H98,y2 ∼1) has been achieved simultaneously by combining an upstream deuterium (D2) puff and divertor argon (Ar) seeding. Both experimental and SOLPS-ITER modeling reveal that additional D2 puff can further mitigate the target heat load and facilitate the detachment. The SOLPS-ITER results also show that the D2 puff makes a limited contribution to the Ar line radiation but a significant contribution to the neutral radiation in the SOL and divertor regions. The physical mechanism behind the effect of the D2 puff on the Ar retention is also revealed by the modeling. The increase in the Ar velocity is the major reason for the improved Ar retention in the partial detachment state. The increase in vAr is mainly caused by the strengthening of frictional drag of D+, which is because the additional D2 puff increases the pressure gradient force (FPG) and the electric field force (FE) on D+. Further analysis reveals that in the deep detachment state, some other negative effects play a dominant role in determining the Ar retention, such as the shift of the region of the Ar+ ionization source, the decrease in the strength of the Ar+ ionization source, and the net force on the Ar ions near the target.


  • Open Access

    Experiment study of m/n = 1/1 mode saturation level in high-βp discharge on the EAST tokamak

    by Wei Wang, Liqing Xu, X. Gong, Jinping Qian, Bin Zhang, Hailin Zhao, Pan Li, Wenbin Liu, Ruirong Liang, Yunchan Hu, et al.

    The saturated internal kink mode with m/n = 1/1 has been observed in the H-mode discharge of the experimental advanced superconducting tokamak, characterized by high βP and weak magnetic shear in the core. This observation was made using a combination of soft x-ray imaging and electron cyclotron emission diagnostics. It was noted that the repetitive bursting of m/n = 1/1 internal mode (large amplitude, short bursting duration) transitions into a long-lasting continuous one (small amplitude, constant frequency), when βp> 2.2 in H-mode, a much shorter bursting duration, transitioning into a long-lasting continuous one, with smaller amplitude and a constant frequency. Conversely, for typical βp< 1.5 in L/I discharge, the frequency of m/n = 1/1 mode decreases with time, associated with local poloidal electron diamagnetism drift velocity. The benign m/n = 1/1 mode in high βp has an amplitude much smaller than one in L-mode for high βP stabilization effect. By adjusting the power deposition of electron cyclotron resonance heating, it is found that the saturation level of m/n = 1/1 mode is independent of the local electron temperature gradient in H-mode discharge. It underscores that the flat current and, hence, weak magnetic shear are crucial factors influencing the saturation level of the m/n = 1/1 mode for both the off-axis electron cyclotron current driving current-dominant and off-axis bootstrap current-dominant cases. Furthermore, the outward movement with growth of the m/n = 1/1 mode in the process of L-H mode transition and the characteristic time of this process are close to the current diffusion time.

  • Hot spots of the main limiter induced by fast ions in experimental advanced superconducting tokamak (EAST)

    by Y. L. Li, Y. F. Xu, X. Y. Xu, G. S. Xu, R. R. Liang, R. Ding, X. Liu, K. N. Geng, T. Zhang, S. X. Wang, et al.

    The main limiter in EAST was observed to endure a high heat load and was cracked near the midplane at the right side during the plasma operation. To explore the heat load carried by fast ion loss toward the main limiter, the neutral beam injection (NBI) and radio frequency power proportion experiment was conducted in EAST where the plasma stored energy and line integrated density were kept almost constant. The hot spot at the right side of the main limiter was observed to be enhanced by co-current perpendicular (co-perp) NBI. An NBI ion loss simulation was performed in the presence of the toroidal field ripple and the Coulomb collision by using the orbit code GYCAVA and the NBI code TGCO. The result indicates that the NBI ion loss by ripple and collision mainly causes a bright area below the midplane of the right side of the main limiter as observed in the EAST experiment. The peak heat load of lost fast ions generated by co-perp NBI is ∼0.5 MW/m2 as obtained by 1 MW of NBI deposited power and comparable with the heat load carried by fast electrons induced by lower hybrid current drive. In addition, increasing the gap between the separatrix and the first-wall limiters in the simulation is found to reduce this heat load.


  • Open Access

    Improvement of lower hybrid current drive systems for high-power and long-pulse operation on EAST

    by M. Wang, L. Liu, L.M. Zhao, M.H. Li, W.D. Ma, H.C. Hu, Z.G. Wu, J.Q. Feng, Y. Yang, L. Zhu, et al.


  • Observation of direct power deposition of ICRF in EAST plasma boundary

    by X. L. Li, Y. L. Li, G. S. Xu, H. Zhang, J. Xu, A. Li, C. J. Xiao, S. T. Mao, R. R. Liang, L. Zhang, et al.

    Waves in the ion-cyclotron range of frequencies (ICRF) used for plasma heating are known to interact strongly with the scrape-off layer (SOL) plasma, potentially limiting ICRF performance. We present the evidence of direct power deposition of ICRF in the Experimental Advanced Superconducting Tokamak (EAST) plasma boundary, with two ICRF antennas and 12 MW of ICRF source power in support of high-power and long-pulse operation. By applying Retarding Field Analyzer (RFA) diagnostic, a sharp rise in average collected ion parallel energy was obtained during the period of ICRF heating as the RFA probe stayed still at 2 mm behind the main limiter which indicates that a certain amount of power is deposited near the limiter instead of being absorbed by the main plasma. A significant increase of the target floating potential in electron temperature measured by Divertor Langmuir Probes arrays was observed. The wall temperature in the far SOL was also enhanced. As a consequence, an enhancement of the carbon and tungsten impurity concentration was observed both at the plasma boundary and core. Besides, plasma radiation, the impurity concentration of the boundary and core increased, and the temperature rise of the first wall was also observed, which are intuitive and powerful pieces of evidence of ICRF direct power deposition at the boundary.