Guoen Weng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Guoen Weng has a total of 125 co-authors. Here are the top co-authors by number of shared publications:
- Shaoqiang Chen
East China Normal University
39 shared publications Xiaobo Hu
East China Normal University 500 Dongchuan Road
28 shared publicationsJunhao Chu
East China Normal University 500 Dongchuan Road
22 shared publicationsHidefumi Akiyama
The University of Tokyo
19 shared publicationsYouyang Wang
Nanjing University of Science and Technology
13 shared publicationsFuyi Cao
The University of Tokyo 5-1-5 Kashiwanoha
12 shared publications
Latest Publications
- 29 October 2026
- Published by American Chemical Society (ACS) in ACS Photonics
Ultrafast and Low Threshold Quasi-2D/3D Perovskite Wrap-Around Heterostructure Microlasers
Quasi-2D/3D perovskite heterostructures have shown great promise for both light-harvesting and light-emitting applications for their attractive properties, including high humidity stability, effective defect passivation, enhanced carrier/exciton transport, and efficient energy funneling from quasi-2D perovskite quantum wells to 3D bulk crystals. In previous studies, quasi-2D/3D heterostructures were typically fabricated using a two-step method. Here, for the first time, we report an innovative perovskite microcavity with a quasi-2D/3D wrap-around heterostructure prepared via a one-step method, consisting of (BA)2Csn–1PbnBr3n+1 quasi-2D films and 3D bulk. The microcavity exhibits an ultralow lasing threshold of 2.12 μJ/cm2, which is attributed to significantly enhanced carrier/exciton injection enabled by rapid energy funneling across the wrap-around heterojunction interfaces. Notably, this heterostructure can markedly reduce both the delay time and pulse width of the laser emission, thereby further expands its potential applications in ultrafast optical switches and flip-flops. The origin of these ultrafast characteristics is elucidated by a proposed carrier/exciton dynamics model, which is further validated unambiguously by rate-equation simulations. This work provides a comprehensive understanding of the fundamental carrier/exciton dynamics and the unique photophysical kinetics involved in the lasing process of perovskite wrap-around heterojunction microcavities and is expected to advance their technological potential in integrated photonics.
- 29 October 2026
- Published by American Chemical Society (ACS) in ACS Photonics
Ultrafast and Low Threshold Quasi-2D/3D Perovskite Wrap-Around Heterostructure Microlasers
Quasi-2D/3D perovskite heterostructures have shown great promise for both light-harvesting and light-emitting applications for their attractive properties, including high humidity stability, effective defect passivation, enhanced carrier/exciton transport, and efficient energy funneling from quasi-2D perovskite quantum wells to 3D bulk crystals. In previous studies, quasi-2D/3D heterostructures were typically fabricated using a two-step method. Here, for the first time, we report an innovative perovskite microcavity with a quasi-2D/3D wrap-around heterostructure prepared via a one-step method, consisting of (BA)2Csn–1PbnBr3n+1 quasi-2D films and 3D bulk. The microcavity exhibits an ultralow lasing threshold of 2.12 μJ/cm2, which is attributed to significantly enhanced carrier/exciton injection enabled by rapid energy funneling across the wrap-around heterojunction interfaces. Notably, this heterostructure can markedly reduce both the delay time and pulse width of the laser emission, thereby further expands its potential applications in ultrafast optical switches and flip-flops. The origin of these ultrafast characteristics is elucidated by a proposed carrier/exciton dynamics model, which is further validated unambiguously by rate-equation simulations. This work provides a comprehensive understanding of the fundamental carrier/exciton dynamics and the unique photophysical kinetics involved in the lasing process of perovskite wrap-around heterojunction microcavities and is expected to advance their technological potential in integrated photonics.
- 13 October 2026
- Published by Optica Publishing Group in Optics Continuum
- Vol. 5 (10) , 3420
Wavelength-tunable lasing from Mn-doped CsPbBr 3 microcavities
In the past decade, researchers have mainly achieved wavelength-tunable emission of lead halide perovskites through halogen substitution. This involves a complex ion replacement process. Doping Mn 2+ in halide perovskites to replace Pb 2+ can cause lattice contraction, due to the smaller atomic radius of Mn 2+ compared to Pb 2+ . Furthermore, it is environmentally friendly. However, although Mn doping has been widely used to modulate the emission of perovskite materials, tunable lasing emission in Mn-doped inorganic perovskite single-crystal microcavities remains unreported. Herein, we synthesized a CsMn x Pb 1−x Br 3 single-crystal microcavity via a low-cost two-step spin-coating method, with EDS confirming uniform Mn 2+ doping. We achieved photoluminescence wavelength tunability of the microcavity from 472 to 540 nm and implemented lasing. Transient dynamics revealed a non-monotonic lasing delay time caused by the Mn 2+ doping, with a 24 ps/nm chirp verifying rapid carrier consumption. This work fills the research gap and supports transition metal-doped microcavity lasers for integrated photonics.
- 13 October 2026
- Published by Optica Publishing Group in Optics Continuum
- Vol. 5 (10) , 3420
Wavelength-tunable lasing from Mn-doped CsPbBr 3 microcavities
In the past decade, researchers have mainly achieved wavelength-tunable emission of lead halide perovskites through halogen substitution. This involves a complex ion replacement process. Doping Mn 2+ in halide perovskites to replace Pb 2+ can cause lattice contraction, due to the smaller atomic radius of Mn 2+ compared to Pb 2+ . Furthermore, it is environmentally friendly. However, although Mn doping has been widely used to modulate the emission of perovskite materials, tunable lasing emission in Mn-doped inorganic perovskite single-crystal microcavities remains unreported. Herein, we synthesized a CsMn x Pb 1−x Br 3 single-crystal microcavity via a low-cost two-step spin-coating method, with EDS confirming uniform Mn 2+ doping. We achieved photoluminescence wavelength tunability of the microcavity from 472 to 540 nm and implemented lasing. Transient dynamics revealed a non-monotonic lasing delay time caused by the Mn 2+ doping, with a 24 ps/nm chirp verifying rapid carrier consumption. This work fills the research gap and supports transition metal-doped microcavity lasers for integrated photonics.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (19) , 8629-8635
Fast and Wide-Range Wavelength Tuning of a III–V/Si 3 N 4 External-Cavity Laser via Two-Step Pulsed Heating
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (19) , 8629-8635
Fast and Wide-Range Wavelength Tuning of a III–V/Si 3 N 4 External-Cavity Laser via Two-Step Pulsed Heating
- Open Access
- 25 July 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (15)
Wavelength and Pulsewidth Tunable Flexible CsPbBr 3 Perovskite Microlasers by Mechanical Stress Modulation
Strain‐induced wavelength‐tunable flexible lasers hold considerable promise in wearable devices and multifunctional electronic skin. Furthermore, their dynamic pulse parameter adjustability with picosecond‐level temporal resolution provides extended potential in high‐precision dynamic monitoring, high‐speed anti‐interference communication, and precision sensing. Here, we report a flexible CsPbBr 3 perovskite microlaser with spectral tunability of 1.59 nm in wavelength and 14 ps in laser pulsewidth through mechanical stress modulation. The device exhibits a low threshold density of 2 , a high respond speed with a delay time of <70 ps, and an ultrashort optical pulse with a minimum duration of 10.8 ps. The strain‐induced evolution of the gain‐switched pulsed laser outputs, including pulsewidth, delay time, and photon decay were systematically explored, for the first time, by taking the strain–photon synergetic coupling mechanism into account. Additionally, the stress dependences of the laser pulse behaviors are physically revealed by theoretical simulations using the Hamiltonian matrix combined with rate equations. Our results provide not only a better understanding of lasing in flexible perovskite microcavity systems under stress, but also a new platform for high‐precision stress monitoring by picosecond‐level pulsewidth sensing.
- 25 July 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (15)
Open AccessWavelength and Pulsewidth Tunable Flexible CsPbBr 3 Perovskite Microlasers by Mechanical Stress Modulation
Strain‐induced wavelength‐tunable flexible lasers hold considerable promise in wearable devices and multifunctional electronic skin. Furthermore, their dynamic pulse parameter adjustability with picosecond‐level temporal resolution provides extended potential in high‐precision dynamic monitoring, high‐speed anti‐interference communication, and precision sensing. Here, we report a flexible CsPbBr 3 perovskite microlaser with spectral tunability of 1.59 nm in wavelength and 14 ps in laser pulsewidth through mechanical stress modulation. The device exhibits a low threshold density of 2 , a high respond speed with a delay time of <70 ps, and an ultrashort optical pulse with a minimum duration of 10.8 ps. The strain‐induced evolution of the gain‐switched pulsed laser outputs, including pulsewidth, delay time, and photon decay were systematically explored, for the first time, by taking the strain–photon synergetic coupling mechanism into account. Additionally, the stress dependences of the laser pulse behaviors are physically revealed by theoretical simulations using the Hamiltonian matrix combined with rate equations. Our results provide not only a better understanding of lasing in flexible perovskite microcavity systems under stress, but also a new platform for high‐precision stress monitoring by picosecond‐level pulsewidth sensing.
- 6 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (1)
A comparative study of optical confinement and strain in GaN microdisk lasers with semi-suspended and DBR-based structures
In this study, GaN-based microdisk lasers with two different underlying structures, namely, a bottom distributed Bragg reflector (DBR) based structure and a semi-suspended structure formed through partial undercutting of the former, are fabricated from the same epitaxial wafer and systematically compared. The distinct strain distributions, optical confinements, and their combined effects on the lasing characteristics are thoroughly analyzed. The bottom DBRs introduce additional tensile strain in the top GaN layer, effectively mitigating the quantum-confined Stark effect, but provide no significant advantage in whispering-gallery-mode confinement compared to the semi-suspended structure. Owing to the synergistic influence of strain and optical confinement, the semi-suspended devices exhibit lower thresholds, narrower linewidths, shorter lasing wavelengths, and faster stimulated-emission rates.
- 6 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (1)
A comparative study of optical confinement and strain in GaN microdisk lasers with semi-suspended and DBR-based structures
In this study, GaN-based microdisk lasers with two different underlying structures, namely, a bottom distributed Bragg reflector (DBR) based structure and a semi-suspended structure formed through partial undercutting of the former, are fabricated from the same epitaxial wafer and systematically compared. The distinct strain distributions, optical confinements, and their combined effects on the lasing characteristics are thoroughly analyzed. The bottom DBRs introduce additional tensile strain in the top GaN layer, effectively mitigating the quantum-confined Stark effect, but provide no significant advantage in whispering-gallery-mode confinement compared to the semi-suspended structure. Owing to the synergistic influence of strain and optical confinement, the semi-suspended devices exhibit lower thresholds, narrower linewidths, shorter lasing wavelengths, and faster stimulated-emission rates.
- 24 March 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9)
End-to-end hardware-in-the-loop temperature control for semiconductor laser based on deep reinforcement learning
This paper presents a temperature control system for semiconductor lasers, employing a novel end-to-end hardware-in-the-loop control strategy that integrates deep reinforcement learning control with mechanical structure design. Three mechanical structures were proposed and simulated to enhance temperature control flexibility and uniformity: single-stage (Fan only and TEC only) and dual-stage (TEC + Fan), where TEC refers to the thermal electric cooler. Simulations demonstrate that the dual-stage structure under the same driving conditions provides superior temperature control flexibility and uniformity. The key innovation lies in the end-to-end hardware-in-the-loop control strategy based on deep reinforcement learning. The End-to-end Deep Reinforcement Learning (E2EDRL) algorithm is capable of autonomously exploring optimal control policies without manual tuning. Simulation results demonstrate that, compared with the Proximal Policy Optimization (PPO) and Soft Actor-Critic (SAC) algorithms, E2EDRL not only achieves the highest performance metrics but also converges within a reasonable number of episodes (approximately 45). This approach achieves structure-algorithm synergy, thereby comprehensively accounting for system-level factors. Experimental results demonstrate substantial performance improvements, achieving temperature fluctuation control within ±0.8 °C, optical power fluctuations limited to 2.2%, and an 87% reduction in central wavelength redshift. Furthermore, the system demonstrates robust intelligent behavior and adaptability across a broad range of temperature control scenarios, underscoring its potential for advanced thermal management applications in semiconductor lasers.
- 24 March 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9)
End-to-end hardware-in-the-loop temperature control for semiconductor laser based on deep reinforcement learning
This paper presents a temperature control system for semiconductor lasers, employing a novel end-to-end hardware-in-the-loop control strategy that integrates deep reinforcement learning control with mechanical structure design. Three mechanical structures were proposed and simulated to enhance temperature control flexibility and uniformity: single-stage (Fan only and TEC only) and dual-stage (TEC + Fan), where TEC refers to the thermal electric cooler. Simulations demonstrate that the dual-stage structure under the same driving conditions provides superior temperature control flexibility and uniformity. The key innovation lies in the end-to-end hardware-in-the-loop control strategy based on deep reinforcement learning. The End-to-end Deep Reinforcement Learning (E2EDRL) algorithm is capable of autonomously exploring optimal control policies without manual tuning. Simulation results demonstrate that, compared with the Proximal Policy Optimization (PPO) and Soft Actor-Critic (SAC) algorithms, E2EDRL not only achieves the highest performance metrics but also converges within a reasonable number of episodes (approximately 45). This approach achieves structure-algorithm synergy, thereby comprehensively accounting for system-level factors. Experimental results demonstrate substantial performance improvements, achieving temperature fluctuation control within ±0.8 °C, optical power fluctuations limited to 2.2%, and an 87% reduction in central wavelength redshift. Furthermore, the system demonstrates robust intelligent behavior and adaptability across a broad range of temperature control scenarios, underscoring its potential for advanced thermal management applications in semiconductor lasers.
- Open Access
- 1 March 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (3)
Picosecond low-threshold random lasing in polymer passivated CsPbBr3 thin films
All-inorganic CsPbX3 (X = Cl, Br, I) perovskites have demonstrated great potential for optoelectronic applications due to their excellent optical properties and environmental stability. Random lasing is a particularly promising direction because of its simple and cavity-free feedback mechanism. However, efficient random lasing in CsPbX3 thin films remains challenging because of their high defect densities, non-radiative recombination rate, and poor surface morphology. Herein, we present a simple method to fabricate high-quality CsPbBr3 thin films, using polymethyl methacrylate–toluene solution as antisolvent, which simultaneously enables surface passivation of perovskite crystals. The as-synthesized films exhibit improved crystallinity, smoother morphology, and prolonged carrier lifetime. Owing to these factors, the films achieve a low threshold random lasing (9.59 µJ/cm2), along with an ultrafast photon decay of 3.14 ps at 2.4 times the threshold. Notably, the random lasing can be realized across the sample area. This work highlights the effect of polymer passivation in enhancing film quality and enabling low-threshold, short-pulse random lasing. These findings provide a promising strategy for large-area, multi-point integrated photonics applications based on perovskite thin films.
- 1 March 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (3)
Open AccessPicosecond low-threshold random lasing in polymer passivated CsPbBr3 thin films
All-inorganic CsPbX3 (X = Cl, Br, I) perovskites have demonstrated great potential for optoelectronic applications due to their excellent optical properties and environmental stability. Random lasing is a particularly promising direction because of its simple and cavity-free feedback mechanism. However, efficient random lasing in CsPbX3 thin films remains challenging because of their high defect densities, non-radiative recombination rate, and poor surface morphology. Herein, we present a simple method to fabricate high-quality CsPbBr3 thin films, using polymethyl methacrylate–toluene solution as antisolvent, which simultaneously enables surface passivation of perovskite crystals. The as-synthesized films exhibit improved crystallinity, smoother morphology, and prolonged carrier lifetime. Owing to these factors, the films achieve a low threshold random lasing (9.59 µJ/cm2), along with an ultrafast photon decay of 3.14 ps at 2.4 times the threshold. Notably, the random lasing can be realized across the sample area. This work highlights the effect of polymer passivation in enhancing film quality and enabling low-threshold, short-pulse random lasing. These findings provide a promising strategy for large-area, multi-point integrated photonics applications based on perovskite thin films.
- 5 January 2026
- Published by Wiley in Annalen der Physik
- Vol. 538 (1)
Ultrafast Carrier Dynamics and Laser Pulse Generation in Halide Perovskite Semiconductors
Halide perovskites (HPs) are among the most promising semiconductor candidates for ultrashort pulse generation due to their intrinsic high material gain and ultrafast carrier dynamics. By introducing an ingeniously‐designed cavity structure, picosecond (ps) or even femtosecond (fs) laser pulses can be plausibly obtained from the perovskite devices for a wide variety of applications. A comprehensive understand of the carrier density dependence of exciton transport and recombination as well as light‒matter interaction can help researchers gain deeper insight into the ultrashort pulse generation during lasing. Here, an overview of the recent progress on ultrafast charge carrier dynamics in 3D bulk single‐crystal perovskites as well as quantum‐confined 2D/quasi‐2D Ruddlesden–Popper perovskites and 0D perovskite nanocrystals/quantum‐dots is provided. Additionally, state‐of‐the‐art developments in pulse generation from various perovskite lasers are summarized, with particular attention paid to gain‐switched ultrashort laser pulse emission in different HP microcavities. The physical mechanisms that influence the pulse characteristics of HP lasers based on a rate equation model is also discussed. Finally, the challenges and future prospects of HPs in realizing ultrashort fs‐optical pulses for practical applications are discussed emphatically.
- 5 January 2026
- Published by Wiley in Annalen der Physik
- Vol. 538 (1)
Ultrafast Carrier Dynamics and Laser Pulse Generation in Halide Perovskite Semiconductors
Halide perovskites (HPs) are among the most promising semiconductor candidates for ultrashort pulse generation due to their intrinsic high material gain and ultrafast carrier dynamics. By introducing an ingeniously‐designed cavity structure, picosecond (ps) or even femtosecond (fs) laser pulses can be plausibly obtained from the perovskite devices for a wide variety of applications. A comprehensive understand of the carrier density dependence of exciton transport and recombination as well as light‒matter interaction can help researchers gain deeper insight into the ultrashort pulse generation during lasing. Here, an overview of the recent progress on ultrafast charge carrier dynamics in 3D bulk single‐crystal perovskites as well as quantum‐confined 2D/quasi‐2D Ruddlesden–Popper perovskites and 0D perovskite nanocrystals/quantum‐dots is provided. Additionally, state‐of‐the‐art developments in pulse generation from various perovskite lasers are summarized, with particular attention paid to gain‐switched ultrashort laser pulse emission in different HP microcavities. The physical mechanisms that influence the pulse characteristics of HP lasers based on a rate equation model is also discussed. Finally, the challenges and future prospects of HPs in realizing ultrashort fs‐optical pulses for practical applications are discussed emphatically.
- 4 December 2025
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 12 (12) , 6964-6974
Cyclodextrin-Modified CsPbBr 3 Quantum Dots for Room-Temperature Single-Mode Vertical-Cavity Surface-Emitting Lasers
- 4 December 2025
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 12 (12) , 6964-6974
Cyclodextrin-Modified CsPbBr 3 Quantum Dots for Room-Temperature Single-Mode Vertical-Cavity Surface-Emitting Lasers
- Open Access
- 1 August 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (8)
High crystal quality in InGaN-based green light-emitting diodes with superlattice strain-relaxation layer: Characterization and efficiency improvement strategy
High indium composition in green-light InGaN/GaN light-emitting diodes (LEDs) can lead to significant efficiency degradation, which has not been comprehensively resolved. We made a systematic investigation of high efficiency green InGaN LEDs with the insertion of superlattices (SLs) and their epitaxial wafers. We elucidated the mechanistic role of SLs in suppressing the localization effect mainly by temperature-dependent photoluminescence (PL). Further corroboration of the good crystalline quality is provided via power-dependent PL and thermal admittance spectroscopy (TAS). The homogeneity of indium composition could suppress the Shockley–Read–Hall recombination significantly: a radiative efficiency of more than 44.7% at 300 K was achieved, and no identifiable defect levels were found by TAS. However, the overall radiative efficiency was still limited due to electron crowding in the quantum well closest to the p-type region and inadequate hole injection, illustrated by the capacitance–voltage measurements and the simulation results with the finite element method. Our analysis along with the introduced improvement strategy could provide relatively comprehensive guidance for subsequent designs.
- 1 August 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (8)
Open AccessHigh crystal quality in InGaN-based green light-emitting diodes with superlattice strain-relaxation layer: Characterization and efficiency improvement strategy
High indium composition in green-light InGaN/GaN light-emitting diodes (LEDs) can lead to significant efficiency degradation, which has not been comprehensively resolved. We made a systematic investigation of high efficiency green InGaN LEDs with the insertion of superlattices (SLs) and their epitaxial wafers. We elucidated the mechanistic role of SLs in suppressing the localization effect mainly by temperature-dependent photoluminescence (PL). Further corroboration of the good crystalline quality is provided via power-dependent PL and thermal admittance spectroscopy (TAS). The homogeneity of indium composition could suppress the Shockley–Read–Hall recombination significantly: a radiative efficiency of more than 44.7% at 300 K was achieved, and no identifiable defect levels were found by TAS. However, the overall radiative efficiency was still limited due to electron crowding in the quantum well closest to the p-type region and inadequate hole injection, illustrated by the capacitance–voltage measurements and the simulation results with the finite element method. Our analysis along with the introduced improvement strategy could provide relatively comprehensive guidance for subsequent designs.