Gerald L. Ullman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gerald L. Ullman has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Laura L. Higgins
Texas A&M Transportation Institute, College Station, TX
2 shared publications - LuAnn Theiss
Work Zone and Dynamic Message Sign Program, Texas A&M Transportation Institute, College Station, TX
2 shared publications - Chris L. Simek
Texas A&M Transportation Institute, College Station, TX
1 shared publication Dave Wolfe
Drive Engineering Corporation, Blue Bell, PA
1 shared publicationElisabeth Rose
Texas Engineering Experiment Station, Texas A&M University System, 3126 TAMU, College Station, TX 77843-3126
1 shared publication- Ezekiel Y. Hsieh
Univ. of Texas at Austin
1 shared publication
Latest Publications
- Open Access
- 28 March 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (10) , 877-886
Improved Temporary Traffic Control Guidance for Mobile Operations on Two-Lane Roadways
The objective of this research was to develop guidance for improving safety at mobile operations on two-lane roadways. One of the most significant hazards to workers performing mobile operations is unpredictable driver behavior around the operation (including poor passing decisions). Researchers observed 1,209 passing maneuvers at 17 different mobile operations in Texas and Minnesota, U.S., to better understand driver behavior around mobile operations. An analysis of the passing maneuver data showed that 449 passing maneuvers were made by drivers who were not first in the queue of vehicles behind the mobile operation. These passing maneuvers were considered undesirable because they indicate some degree of driver impatience. Researchers analyzed the amount of time each driver spent in the queue and found that nearly 50% of drivers who waited in the queue for 4 min or longer attempted an undesirable passing maneuver. This increased to nearly 85% when wait times exceed 6 min. As a result of the field studies, the researchers recommended that transportation agencies strive to avoid creating situations where drivers in queue must follow a mobile operation for several minutes without opportunities to pass. When these delays cannot be avoided, the work crew may need to pull over and allow vehicles to pass. If there are no suitable pullover locations, a stationary work zone with positive traffic control methods (e.g., flaggers, portable signals) should be considered.
- 28 March 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (10) , 877-886
Open AccessImproved Temporary Traffic Control Guidance for Mobile Operations on Two-Lane Roadways
The objective of this research was to develop guidance for improving safety at mobile operations on two-lane roadways. One of the most significant hazards to workers performing mobile operations is unpredictable driver behavior around the operation (including poor passing decisions). Researchers observed 1,209 passing maneuvers at 17 different mobile operations in Texas and Minnesota, U.S., to better understand driver behavior around mobile operations. An analysis of the passing maneuver data showed that 449 passing maneuvers were made by drivers who were not first in the queue of vehicles behind the mobile operation. These passing maneuvers were considered undesirable because they indicate some degree of driver impatience. Researchers analyzed the amount of time each driver spent in the queue and found that nearly 50% of drivers who waited in the queue for 4 min or longer attempted an undesirable passing maneuver. This increased to nearly 85% when wait times exceed 6 min. As a result of the field studies, the researchers recommended that transportation agencies strive to avoid creating situations where drivers in queue must follow a mobile operation for several minutes without opportunities to pass. When these delays cannot be avoided, the work crew may need to pull over and allow vehicles to pass. If there are no suitable pullover locations, a stationary work zone with positive traffic control methods (e.g., flaggers, portable signals) should be considered.
- 31 March 2023
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (9) , 164-174
Driver Understanding and Secondary Task Performance While Viewing Traffic Safety Messages on Dynamic Message Signs
Many agencies use dynamic message signs to display behavioral traffic safety (BTS) messages (e.g., CLICK IT OR TICKET, DONT DRINK AND DRIVE). However, little guidance exists on how best to design and display such messages on those signs. In this paper, the results of a human factors laptop-based study are described, which examined how well drivers can read and interpret BTS messages while simultaneously attending to a secondary control task similar to how drivers must operate their vehicle while simultaneously reading road signs. The study results indicated that displaying BTS messages that include humor, wit, or pop culture references could have adverse consequences on driving behavior for motorists who are unable to correctly interpret the safety topic of those messages. The results also indicated that BTS messages should only address a single safety topic. The length of the BTS message should be kept to 16 words or fewer in low to moderate driver workload environments; in high driver workload environments, BTS messages should be limited to 11 words or fewer.
- 31 March 2023
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (9) , 164-174
Driver Understanding and Secondary Task Performance While Viewing Traffic Safety Messages on Dynamic Message Signs
Many agencies use dynamic message signs to display behavioral traffic safety (BTS) messages (e.g., CLICK IT OR TICKET, DONT DRINK AND DRIVE). However, little guidance exists on how best to design and display such messages on those signs. In this paper, the results of a human factors laptop-based study are described, which examined how well drivers can read and interpret BTS messages while simultaneously attending to a secondary control task similar to how drivers must operate their vehicle while simultaneously reading road signs. The study results indicated that displaying BTS messages that include humor, wit, or pop culture references could have adverse consequences on driving behavior for motorists who are unable to correctly interpret the safety topic of those messages. The results also indicated that BTS messages should only address a single safety topic. The length of the BTS message should be kept to 16 words or fewer in low to moderate driver workload environments; in high driver workload environments, BTS messages should be limited to 11 words or fewer.
- 14 September 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (3) , 1080-1084
Assessment of Driver Distraction at Work Zones with Portable Rumble Strip Deployments in Texas
The objective of this research was to assess the extent of distracted driving occurring on roadways in Texas, U.S., as drivers approach a work zone and the extent to which portable rumble strips (PRS) may influence those rates. The research team utilized direct field observations of drivers approaching work zones at several Texas work zones. At each work zone, team members positioned themselves near the location of the upstream set of PRS. Team members also collected observational data at a second location downstream from that initial PRS location. The results of the field studies showed that nearly one in five motorists are visually distracted in some manner while driving as they approach a work zone. The studies also showed that this rate of visual distraction decreased at distances closer to the work zone. Observations of distracted drivers as they passed over the PRS indicate that at least some of that decrease in distraction over distance was because of the presence of the PRS. Data were not sufficient to determine conclusively how long the distraction-reducing effects of PRS last. However, data from one site suggest that the effect was limited to the first 1,500 ft after traversing the PRS.
- 14 September 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (3) , 1080-1084
Assessment of Driver Distraction at Work Zones with Portable Rumble Strip Deployments in Texas
The objective of this research was to assess the extent of distracted driving occurring on roadways in Texas, U.S., as drivers approach a work zone and the extent to which portable rumble strips (PRS) may influence those rates. The research team utilized direct field observations of drivers approaching work zones at several Texas work zones. At each work zone, team members positioned themselves near the location of the upstream set of PRS. Team members also collected observational data at a second location downstream from that initial PRS location. The results of the field studies showed that nearly one in five motorists are visually distracted in some manner while driving as they approach a work zone. The studies also showed that this rate of visual distraction decreased at distances closer to the work zone. Observations of distracted drivers as they passed over the PRS indicate that at least some of that decrease in distraction over distance was because of the presence of the PRS. Data were not sufficient to determine conclusively how long the distraction-reducing effects of PRS last. However, data from one site suggest that the effect was limited to the first 1,500 ft after traversing the PRS.
- 25 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (1) , 1130-1140
Improved Practices for Temporary Work Zone Guide Signs
Freeway reconstruction projects often involve adding lanes and improving entrance and exit ramps. Sign supports for overhead guide signs are sometimes removed early in the project to make way for construction activities. In addition, roadside guide signs may need to be relocated and replaced with temporary guide signs. The Manual on Uniform Traffic Control Devices provides guidance for work zone guide signs in Part 6, stating that temporary guide signs shall have black legend and border on an orange background. But permanent guide signs follow Part 2 of the MUTCD, which prescribes white legend and border on a green background for guide signs in general. Thus, many long-term freeway work zones may have guide signs in both color schemes that change throughout the project as the construction work progresses. The constrained conditions often seen in these work zones can also result in guide signs that use a variety of fonts, font sizes, sign sizes, and placement positions. This paper describes the human factors study that was performed to assess motorist understanding of various work zone guide signage strategies. Based on the results, the researchers were able to develop recommendations for long-term work zone guide sign design and placement to improve uniformity for the traveling public.
- 25 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (1) , 1130-1140
Improved Practices for Temporary Work Zone Guide Signs
Freeway reconstruction projects often involve adding lanes and improving entrance and exit ramps. Sign supports for overhead guide signs are sometimes removed early in the project to make way for construction activities. In addition, roadside guide signs may need to be relocated and replaced with temporary guide signs. The Manual on Uniform Traffic Control Devices provides guidance for work zone guide signs in Part 6, stating that temporary guide signs shall have black legend and border on an orange background. But permanent guide signs follow Part 2 of the MUTCD, which prescribes white legend and border on a green background for guide signs in general. Thus, many long-term freeway work zones may have guide signs in both color schemes that change throughout the project as the construction work progresses. The constrained conditions often seen in these work zones can also result in guide signs that use a variety of fonts, font sizes, sign sizes, and placement positions. This paper describes the human factors study that was performed to assess motorist understanding of various work zone guide signage strategies. Based on the results, the researchers were able to develop recommendations for long-term work zone guide sign design and placement to improve uniformity for the traveling public.
- 22 April 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 376 (6591) , 347-348
How safe are safety messages?
Highway fatalities increased in response to certain messages
- 22 April 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 376 (6591) , 347-348
How safe are safety messages?
Highway fatalities increased in response to certain messages
- 1 November 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part A: Systems
- Vol. 143 (11)
Effectiveness of End-of-Queue Warning Systems and Portable Rumble Strips on Lane Closure Crashes
The Texas Department of Transportation (TxDOT) has been deploying work zone intelligent transportation systems (ITS) in an effort to reduce the number of work zone crashes along the Interstate 35 (I-35) corridor. Road construction lane closures on I-35 are typically performed at night when traffic volumes are lower but driver awareness is often reduced. The two systems evaluated were temporary portable rumble strips (TPRS) alone and end-of-queue warning systems (EOQWS) combined with TPRS. The EOQWS consist of portable changeable message signs linked to radar speed sensors to proactively warn drivers of queueing and slowed conditions ahead. The TPRS alone were deployed for work zone lane closures where no queues were expected, and both EOQWS and TPRS were deployed for lane closures expected to cause queueing. The effectiveness of these systems was evaluated over 4 years of deployments and compared to 1 year of no deployments. Both TPRS alone and EOQWS with TPRS were found to cause a significant reduction in the number of crashes under queued conditions, 60 and 53%, respectively. Additionally, the severity of the crashes that did occur was significantly reduced under queued conditions when either treatment was in place.
- 1 November 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part A: Systems
- Vol. 143 (11)
Effectiveness of End-of-Queue Warning Systems and Portable Rumble Strips on Lane Closure Crashes
The Texas Department of Transportation (TxDOT) has been deploying work zone intelligent transportation systems (ITS) in an effort to reduce the number of work zone crashes along the Interstate 35 (I-35) corridor. Road construction lane closures on I-35 are typically performed at night when traffic volumes are lower but driver awareness is often reduced. The two systems evaluated were temporary portable rumble strips (TPRS) alone and end-of-queue warning systems (EOQWS) combined with TPRS. The EOQWS consist of portable changeable message signs linked to radar speed sensors to proactively warn drivers of queueing and slowed conditions ahead. The TPRS alone were deployed for work zone lane closures where no queues were expected, and both EOQWS and TPRS were deployed for lane closures expected to cause queueing. The effectiveness of these systems was evaluated over 4 years of deployments and compared to 1 year of no deployments. Both TPRS alone and EOQWS with TPRS were found to cause a significant reduction in the number of crashes under queued conditions, 60 and 53%, respectively. Additionally, the severity of the crashes that did occur was significantly reduced under queued conditions when either treatment was in place.
- 1 January 2016
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2555 (1) , 46-52
Safety Effects of Portable End-of-Queue Warning System Deployments at Texas Work Zones
The reduction of upstream end-of-queue (EOQ) crashes at work zone lane closures has been a focus of the Texas Department of Transportation, Austin, for several years. An ongoing widening effort on Interstate 35 through central Texas prompted officials to examine and implement technologies to mitigate the impacts of EOQ warning crashes. An EOQ warning system was established, which consisted of a highly portable work zone intelligent transportation system of easily deployable radar speed sensors linked to one or more portable changeable message signs and highly portable transverse rumble strips. The EOQ system was deployed upstream of nighttime lane closures, where queues were expected to develop. Although the sample sizes were relatively small, the trends did suggest that the systems were having a positive effect to reduce crashes. Overall, the EOQ warning system was estimated to have reduced crashes 44% from what they otherwise would have been if the system had not been used. The crashes that did occur were less severe, which was most likely because fewer of them were of the high-speed, rear-end-collision variety. With traditional societal crash cost values updated to 2014 dollars, the use of the EOQ warning system at nighttime lane closures reduced crash costs by $1.36 million over the analysis period. This figure equated to $6,313 in crash cost savings per night of deployment. Compared with the approximate costs of procurement and deployment of these systems, a break-even point was achieved after 95 to 190 nights of use.
- 1 January 2016
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2555 (1) , 46-52
Safety Effects of Portable End-of-Queue Warning System Deployments at Texas Work Zones
The reduction of upstream end-of-queue (EOQ) crashes at work zone lane closures has been a focus of the Texas Department of Transportation, Austin, for several years. An ongoing widening effort on Interstate 35 through central Texas prompted officials to examine and implement technologies to mitigate the impacts of EOQ warning crashes. An EOQ warning system was established, which consisted of a highly portable work zone intelligent transportation system of easily deployable radar speed sensors linked to one or more portable changeable message signs and highly portable transverse rumble strips. The EOQ system was deployed upstream of nighttime lane closures, where queues were expected to develop. Although the sample sizes were relatively small, the trends did suggest that the systems were having a positive effect to reduce crashes. Overall, the EOQ warning system was estimated to have reduced crashes 44% from what they otherwise would have been if the system had not been used. The crashes that did occur were less severe, which was most likely because fewer of them were of the high-speed, rear-end-collision variety. With traditional societal crash cost values updated to 2014 dollars, the use of the EOQ warning system at nighttime lane closures reduced crash costs by $1.36 million over the analysis period. This figure equated to $6,313 in crash cost savings per night of deployment. Compared with the approximate costs of procurement and deployment of these systems, a break-even point was achieved after 95 to 190 nights of use.
- 1 January 2005
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 1918 (1) , 92-97
Evaluation of Dynamic Speed Display Signs
- 1 January 2005
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 1918 (1) , 92-97
Evaluation of Dynamic Speed Display Signs
- Open Access
- 1 January 2002
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 1818 (1) , 25-31
Feasibility of Real-Time Remote Speed Enforcement for Work Zones
Studies have shown that a large percentage of vehicles involved in work zone crashes are traveling at excessive speeds. Although traditional speed enforcement has been shown to reduce speeds through the work area, enforcement under these conditions can be dangerous to both the motoring public and enforcement officers. The work zone layout often limits the locations at which an officer can set up to enforce the speed limit and the locations at which violators can be stopped. Automated speed enforcement technology could help eliminate the need to stop violators in a work zone, but it is not currently a popular concept in the United States because of concerns about motorist privacy. Researchers hypothesized that this technology could be useful for work zone enforcement if adapted to a more real-time operation. The initial testing of the concept of remote speed enforcement is summarized. An automated speed enforcement system (consisting of digital video and lidar technology) was meshed with a wireless communications system. The unit determined when vehicles exceeded a certain speed threshold. If a vehicle was detected as exceeding the threshold, a digital photograph was taken of the violator. This photograph was then transmitted to an observer stationed downstream of the site. The technical feasibility of the system was assessed through field tests. Focus groups of law enforcement personnel were used to determine potential acceptance of the system in the law enforcement community. Recommendations for future improvements and possible applications of the system are made.
- 1 January 2002
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 1818 (1) , 25-31
Open AccessFeasibility of Real-Time Remote Speed Enforcement for Work Zones
Studies have shown that a large percentage of vehicles involved in work zone crashes are traveling at excessive speeds. Although traditional speed enforcement has been shown to reduce speeds through the work area, enforcement under these conditions can be dangerous to both the motoring public and enforcement officers. The work zone layout often limits the locations at which an officer can set up to enforce the speed limit and the locations at which violators can be stopped. Automated speed enforcement technology could help eliminate the need to stop violators in a work zone, but it is not currently a popular concept in the United States because of concerns about motorist privacy. Researchers hypothesized that this technology could be useful for work zone enforcement if adapted to a more real-time operation. The initial testing of the concept of remote speed enforcement is summarized. An automated speed enforcement system (consisting of digital video and lidar technology) was meshed with a wireless communications system. The unit determined when vehicles exceeded a certain speed threshold. If a vehicle was detected as exceeding the threshold, a digital photograph was taken of the violator. This photograph was then transmitted to an observer stationed downstream of the site. The technical feasibility of the system was assessed through field tests. Focus groups of law enforcement personnel were used to determine potential acceptance of the system in the law enforcement community. Recommendations for future improvements and possible applications of the system are made.