Vishwanathan Ramar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vishwanathan Ramar has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Palani Balaya
National University of Singapore
6 shared publications P. Balaya
3 shared publicationsS. Hariharan
3 shared publicationsK. Saravanan
2 shared publicationsPalani Balaya
2 shared publications- Saravanan Kuppan
Robert Bosch LLC
2 shared publications
Latest Publications
- Open Access
- 25 September 2024
- Published by Wiley in ChemSusChem
- Vol. 18 (2) , e202400122
Electrochemical Kinetics of LiFePO4 Cathode Material in Non‐flammable Inorganic Liquid Electrolyte
We unveil the fundamental insights of electrochemical kinetics of LFP cathode material and the passivation layer formation in the SO2‐based non‐flammable inorganic liquid electrolyte (IE). The influence of temperature and electrochemical potential cutoff in the electrochemical activity of LFP cathode and IE is disclosed. Furthermore, the materials compatibility, structural and chemical stability of LFP in IE is demonstrated using very slow galvanostatic cycling in combination with LiFePO4||Li0.1FePO4 symmetric cells. The lithium storage performance of LFP half‐cell using inorganic electrolyte is presented with the optimum voltage window. LFP half‐cells exhibit discharge capacities of 147, 111, and 75 mAh/g at 1, 4, 8 C rates, respectively, with coulombic efficiencies of ~99.98 %. The electrochemical behavior and mechanism of LFP||Graphite cell in IE is investigated while concurrently tracking the electrochemical potentials of LFP and Graphite half‐cell.
- 25 September 2024
- Published by Wiley in ChemSusChem
- Vol. 18 (2) , e202400122
Open AccessElectrochemical Kinetics of LiFePO4 Cathode Material in Non‐flammable Inorganic Liquid Electrolyte
We unveil the fundamental insights of electrochemical kinetics of LFP cathode material and the passivation layer formation in the SO2‐based non‐flammable inorganic liquid electrolyte (IE). The influence of temperature and electrochemical potential cutoff in the electrochemical activity of LFP cathode and IE is disclosed. Furthermore, the materials compatibility, structural and chemical stability of LFP in IE is demonstrated using very slow galvanostatic cycling in combination with LiFePO4||Li0.1FePO4 symmetric cells. The lithium storage performance of LFP half‐cell using inorganic electrolyte is presented with the optimum voltage window. LFP half‐cells exhibit discharge capacities of 147, 111, and 75 mAh/g at 1, 4, 8 C rates, respectively, with coulombic efficiencies of ~99.98 %. The electrochemical behavior and mechanism of LFP||Graphite cell in IE is investigated while concurrently tracking the electrochemical potentials of LFP and Graphite half‐cell.
- 1 February 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (2) , 020502
Defect-Enhanced Lithium Storage Performance of Nanostructured Mesoporous LiFePO4 for a High-Power Lithium-Ion Battery
Mesoporous materials have received growing interest, particularly as electrode materials for lithium-ion battery applications since they provide short transportation length for Li ion and electrons, and favour electrolyte wettability. Such unique features are highly beneficial for improving the electrochemical performance of olivine LiFePO4 as this material has intrinsically low electronic and ionic conductivities, which otherwise would affect the storage performance. In addition, this sluggish kinetic brings about huge polarisation specifically at high current rates, resulting in poor energy efficiency. In order to overcome such kinetic issues, we present here a facile soft template-solvothemal method to synthesise mesoporous LiFePO4. Such mesoporous LiFePO4 is made of well interconnected nanograins (20–30 nm) which exhibits excellent storage performance and long-term cycling stability. In particular, the material shows improved storage performance at high rates with significantly less polarisation and clear signature of voltage plateaus for both Li ion insertion-extraction processes. In comparison with the LiFePO4 synthesized by the soft template method, the mesoporous LiFePO4 demonstrates excellent storage performance. This is attributed to the 2-D diffusion of both Li ions and electrons along b- and c-axes consistent with the 2-D Li ions transport reported previously for LiFePO4 single crystal.
- 1 February 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (2) , 020502
Defect-Enhanced Lithium Storage Performance of Nanostructured Mesoporous LiFePO4 for a High-Power Lithium-Ion Battery
Mesoporous materials have received growing interest, particularly as electrode materials for lithium-ion battery applications since they provide short transportation length for Li ion and electrons, and favour electrolyte wettability. Such unique features are highly beneficial for improving the electrochemical performance of olivine LiFePO4 as this material has intrinsically low electronic and ionic conductivities, which otherwise would affect the storage performance. In addition, this sluggish kinetic brings about huge polarisation specifically at high current rates, resulting in poor energy efficiency. In order to overcome such kinetic issues, we present here a facile soft template-solvothemal method to synthesise mesoporous LiFePO4. Such mesoporous LiFePO4 is made of well interconnected nanograins (20–30 nm) which exhibits excellent storage performance and long-term cycling stability. In particular, the material shows improved storage performance at high rates with significantly less polarisation and clear signature of voltage plateaus for both Li ion insertion-extraction processes. In comparison with the LiFePO4 synthesized by the soft template method, the mesoporous LiFePO4 demonstrates excellent storage performance. This is attributed to the 2-D diffusion of both Li ions and electrons along b- and c-axes consistent with the 2-D Li ions transport reported previously for LiFePO4 single crystal.
- 1 October 2016
- Published by Elsevier in Journal of Power Sources
- Vol. 328, 413-421
Heat loss distribution: Impedance and thermal loss analyses in LiFePO4/graphite 18650 electrochemical cell
- 1 October 2016
- Published by Elsevier in Journal of Power Sources
- Vol. 328, 413-421
Heat loss distribution: Impedance and thermal loss analyses in LiFePO4/graphite 18650 electrochemical cell
- 1 February 2016
- Published by Elsevier in Journal of Power Sources
- Vol. 306, 552-558
The effect of polymorphism on the lithium storage performance of Li2MnSiO4
- 1 February 2016
- Published by Elsevier in Journal of Power Sources
- Vol. 306, 552-558
The effect of polymorphism on the lithium storage performance of Li2MnSiO4
- 5 May 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (62) , 50155-50164
Synthesis, characterisation and enhanced electrochemical performance of nanostructured Na2FePO4F for sodium batteries
Nanostructured Na2FePO4F was synthesised by a soft template method, followed by high-energy ball milling (HEBM) and post-heat treatment. The HEBM sample shows excellent sodium storage performance with a discharge capacity of 116 mA h g−1at 0.1 C.
- 5 May 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (62) , 50155-50164
Synthesis, characterisation and enhanced electrochemical performance of nanostructured Na2FePO4F for sodium batteries
Nanostructured Na2FePO4F was synthesised by a soft template method, followed by high-energy ball milling (HEBM) and post-heat treatment. The HEBM sample shows excellent sodium storage performance with a discharge capacity of 116 mA h g−1at 0.1 C.
- 16 August 2013
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 15 (40) , 17240-17249
Enhancing the electrochemical kinetics of high voltage olivine LiMnPO4 by isovalent co-doping
We report here doping of Fe2+ and/or Mg2+ in LiMnPO4 cathode material to enhance its lithium storage performance and appraise the effect of doping. For this purpose, LiMn0.9Fe(0.1−x)MgxPO4/C (x = 0 and 0.05) and LiMn0.95Mg0.05PO4/C have been prepared by a ball mill assisted soft template method. These materials were prepared with similar morphology, particle size and carbon content. Amongst them, the isovalent co-doped LiMn0.9Fe0.05Mg0.05PO4/C sample shows better electrochemical performance compared to LiMn0.9Fe0.1PO4/C and LiMn0.95Mg0.05PO4/C samples. For instance, a lithium storage capacity of 159 mA h g−1 is obtained at 0.1 C for LiMn0.9Fe0.05Mg0.05PO4/C material with a relatively low polarization of ∼139 mV. This is in sharp contrast to LiMn0.9Fe0.1PO4/C and LiMn0.95Mg0.05PO4/C which show only 136.8 and 128.4 mA h g−1 at 0.1 C with the polarization of ∼222 and 334 mV respectively. Further, the LiMn0.9Fe0.05Mg0.05PO4/C electrode delivers discharge capacities of 155.8, 141.4, 118.8, 104.6, 81.4 and 51.8 mA h g−1 at 0.2, 0.5, 1, 2, 5 and 10 C respectively. This electrode material also retains a capacity of 116 mA h g−1 at 1 C after 200 cycles, which is 96% of its initial capacity. Such improved cycling stability of LiMn0.9Fe0.05Mg0.05PO4/C is attributed to the suppressed Mn dissolution in the electrolyte compared to the other samples. Further, during the Li extraction process, delithiated phases created from the Fe2+/Fe3+ redox reaction (∼3.45 V) favor enhanced electrochemical activity of the succeeding Mn2+/Mn3+ redox couples. The fully charged state (4.6 V) contains a partially lithiated phase owing to the presence of electrochemically inactive Mg2+. The presence of such lithiated phase provides a favourable environment for the subsequent lithium insertion process. We also observe improved electronic conductivity and Li-ion diffusion for the co-doped sample compared to LiMnPO4 doped with either Fe2+ or Mg2+ by impedance measurements. The improved storage performance of co-doped LiMnPO4 is thus explained in terms of (i) favorable extraction and insertion reactions and (ii) enhanced transport properties.
- 16 August 2013
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 15 (40) , 17240-17249
Enhancing the electrochemical kinetics of high voltage olivine LiMnPO4 by isovalent co-doping
We report here doping of Fe2+ and/or Mg2+ in LiMnPO4 cathode material to enhance its lithium storage performance and appraise the effect of doping. For this purpose, LiMn0.9Fe(0.1−x)MgxPO4/C (x = 0 and 0.05) and LiMn0.95Mg0.05PO4/C have been prepared by a ball mill assisted soft template method. These materials were prepared with similar morphology, particle size and carbon content. Amongst them, the isovalent co-doped LiMn0.9Fe0.05Mg0.05PO4/C sample shows better electrochemical performance compared to LiMn0.9Fe0.1PO4/C and LiMn0.95Mg0.05PO4/C samples. For instance, a lithium storage capacity of 159 mA h g−1 is obtained at 0.1 C for LiMn0.9Fe0.05Mg0.05PO4/C material with a relatively low polarization of ∼139 mV. This is in sharp contrast to LiMn0.9Fe0.1PO4/C and LiMn0.95Mg0.05PO4/C which show only 136.8 and 128.4 mA h g−1 at 0.1 C with the polarization of ∼222 and 334 mV respectively. Further, the LiMn0.9Fe0.05Mg0.05PO4/C electrode delivers discharge capacities of 155.8, 141.4, 118.8, 104.6, 81.4 and 51.8 mA h g−1 at 0.2, 0.5, 1, 2, 5 and 10 C respectively. This electrode material also retains a capacity of 116 mA h g−1 at 1 C after 200 cycles, which is 96% of its initial capacity. Such improved cycling stability of LiMn0.9Fe0.05Mg0.05PO4/C is attributed to the suppressed Mn dissolution in the electrolyte compared to the other samples. Further, during the Li extraction process, delithiated phases created from the Fe2+/Fe3+ redox reaction (∼3.45 V) favor enhanced electrochemical activity of the succeeding Mn2+/Mn3+ redox couples. The fully charged state (4.6 V) contains a partially lithiated phase owing to the presence of electrochemically inactive Mg2+. The presence of such lithiated phase provides a favourable environment for the subsequent lithium insertion process. We also observe improved electronic conductivity and Li-ion diffusion for the co-doped sample compared to LiMnPO4 doped with either Fe2+ or Mg2+ by impedance measurements. The improved storage performance of co-doped LiMnPO4 is thus explained in terms of (i) favorable extraction and insertion reactions and (ii) enhanced transport properties.
- 1 August 2013
- Published by Elsevier in Electrochimica Acta
- Vol. 105, 496-505
The effect of synthesis parameters on the lithium storage performance of LiMnPO4/C
- 1 August 2013
- Published by Elsevier in Electrochimica Acta
- Vol. 105, 496-505
The effect of synthesis parameters on the lithium storage performance of LiMnPO4/C
- 14 February 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (18) , 6386-6394
Developing a light weight lithium ion battery – an effective material and electrode design for high performance conversion anodes
The process of lithium storage by conversion reaction is a subject of intense research in the field of lithium ion batteries as it opens up the possibility of storing more than one mole of lithium per formula unit, leading to very high storage capacities. For instance, lithium storage by conversion reaction in hematite (α-Fe2O3) results in high theoretical capacity of 1005 mAh g−1. Despite numerous attempts, the first cycle reversibility and cyclability achieved in this material have been disappointingly low. To overcome these limitations, we report here an effective “active material-electrode design” incorporating the following features: (i) well-connected active material particles; (ii) adequate active material surface area; (iii) strong particle-current collector adhesion and (iv) superior degree of electrode drying. Incorporating these features in α-Fe2O3 electrodes enhances its overall electrochemical performance. For the first time, a high first cycle reversibility of 90% is reported for lithium storage via conversion reaction in α-Fe2O3. The long term cyclability over 800 cycles demonstrated here is one of highest reported values for this material. Even at high current densities of 5.025 A g−1 (12 mins of charge/discharge), this tailored α-Fe2O3 delivers capacities (446 mAh g−1) in excess of graphite (372 mAh g−1). Most importantly, this anode material shows feasible operation in a full cell containing olivine LiMn0.8Fe0.2PO4 cathode. It is believed that this simple design approach could also be extended to other material systems such as phosphides, sulphides, nitrides and fluorides that store lithium via conversion mechanism.
- 14 February 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (18) , 6386-6394
Developing a light weight lithium ion battery – an effective material and electrode design for high performance conversion anodes
The process of lithium storage by conversion reaction is a subject of intense research in the field of lithium ion batteries as it opens up the possibility of storing more than one mole of lithium per formula unit, leading to very high storage capacities. For instance, lithium storage by conversion reaction in hematite (α-Fe2O3) results in high theoretical capacity of 1005 mAh g−1. Despite numerous attempts, the first cycle reversibility and cyclability achieved in this material have been disappointingly low. To overcome these limitations, we report here an effective “active material-electrode design” incorporating the following features: (i) well-connected active material particles; (ii) adequate active material surface area; (iii) strong particle-current collector adhesion and (iv) superior degree of electrode drying. Incorporating these features in α-Fe2O3 electrodes enhances its overall electrochemical performance. For the first time, a high first cycle reversibility of 90% is reported for lithium storage via conversion reaction in α-Fe2O3. The long term cyclability over 800 cycles demonstrated here is one of highest reported values for this material. Even at high current densities of 5.025 A g−1 (12 mins of charge/discharge), this tailored α-Fe2O3 delivers capacities (446 mAh g−1) in excess of graphite (372 mAh g−1). Most importantly, this anode material shows feasible operation in a full cell containing olivine LiMn0.8Fe0.2PO4 cathode. It is believed that this simple design approach could also be extended to other material systems such as phosphides, sulphides, nitrides and fluorides that store lithium via conversion mechanism.
- 3 January 2013
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 15 (8) , 2945-2953
A rationally designed dual role anode material for lithium-ion and sodium-ion batteries: case study of eco-friendly Fe3O4
Identifying dual role electrode materials capable of storing both lithium and sodium are thought to be highly relevant, as these materials could find potential applications simultaneously in lithium and sodium ion batteries. In this regard, the concept of dual alkali storage is demonstrated in Fe3O4 anode material undergoing conversion reaction. To enable improved storage, a rational active material and electrode design is proposed. Accordingly, the following features were simultaneously incorporated into the design: (i) an optimal particle size, (ii) a conducting matrix, (iii) adequately large active material surface area and (iv) strong electrode material-current collector integrity. Electrodes incorporating this rational design exhibit excellent high rate performance and impressive cyclability during lithium storage. For instance, Fe3O4 electrodes deliver a charge capacity of 950 mAh g−1 at 1.2 C (∼2.6 times higher than graphite and 5.4 times higher than Li4Ti5O12). Further, these electrodes show no signs of capacity fade even up to 1100 cycles. Impressively, the cells could also be charged–discharged to 65% of their theoretical capacity in just 5 min or 12 C (11.11 A g−1). The rate performance and cyclability of lithium storage achieved here are amongst the highest reported values in the literature for the conversion reaction in Fe3O4. Besides lithium storage, the dual role of this anode is shown by demonstrating its sodium storage ability by conversion reaction for the first time.
- 3 January 2013
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 15 (8) , 2945-2953
A rationally designed dual role anode material for lithium-ion and sodium-ion batteries: case study of eco-friendly Fe3O4
Identifying dual role electrode materials capable of storing both lithium and sodium are thought to be highly relevant, as these materials could find potential applications simultaneously in lithium and sodium ion batteries. In this regard, the concept of dual alkali storage is demonstrated in Fe3O4 anode material undergoing conversion reaction. To enable improved storage, a rational active material and electrode design is proposed. Accordingly, the following features were simultaneously incorporated into the design: (i) an optimal particle size, (ii) a conducting matrix, (iii) adequately large active material surface area and (iv) strong electrode material-current collector integrity. Electrodes incorporating this rational design exhibit excellent high rate performance and impressive cyclability during lithium storage. For instance, Fe3O4 electrodes deliver a charge capacity of 950 mAh g−1 at 1.2 C (∼2.6 times higher than graphite and 5.4 times higher than Li4Ti5O12). Further, these electrodes show no signs of capacity fade even up to 1100 cycles. Impressively, the cells could also be charged–discharged to 65% of their theoretical capacity in just 5 min or 12 C (11.11 A g−1). The rate performance and cyclability of lithium storage achieved here are amongst the highest reported values in the literature for the conversion reaction in Fe3O4. Besides lithium storage, the dual role of this anode is shown by demonstrating its sodium storage ability by conversion reaction for the first time.
- 1 May 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8377, 837703
Influence of nanosize and thermodynamics on lithium storage in insertion and conversion reactions
- 1 May 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8377, 837703
Influence of nanosize and thermodynamics on lithium storage in insertion and conversion reactions