Soo Ouk Jang
Research Subjects
Soo Ouk Jang has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- In Je Kang
Institute of Plasma Technology, Korea Institute of Fusion Energy, Gunsan 54004, Korea
3 shared publications - Chang Hyun Cho
Institute of Plasma Technology, Korea Institute of Fusion Energy, Gunsan 54004, Republic of Korea
2 shared publications - Dae Gun Kim
Research Center, IONES Co., Ltd., Hwaseong 18487, Republic of Korea
2 shared publications - Hyonu Chang
Korea Institute of Fusion Energy
2 shared publications - Hyunjae Park
Institute of Plasma Technology and the Korea Institute of Fusion Energy, Gunsan, South Korea
2 shared publications - Ji Hun Kim
Institute of Plasma Technology, Korea Institute of Fusion Energy, Gunsan, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 8 June 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (25) , 37284-37297
Plasma-Chemical Integration of Solution-Derived ATTT with 3D Carbon Nanowalls for Controllable WS 2 /WO x Hybrid Supercapacitor Electrodes
Two-dimensional (2D) tungsten disulfide (WS2) has attracted considerable interest as a pseudocapacitive material, yet its practical application is often hindered by limited electrical conductivity, complex fabrication routes, and the need for binders. Here, we report a plasma-chemical route for fabricating binder-free, composition-tuned WS2/WO x @CNW hybrid electrodes from solution-deposited ammonium tetrathiotungstate (ATTT) with a downstream hydrogen remote plasma process. By systematically varying the ATTT concentration and microwave power, the surface chemistry of the CNW scaffold is controllably routed into CNW-dominant, WS2-rich, S-oxide-rich, and WO x -dominant regimes while preserving the overall three-dimensional CNW framework, despite partial surface masking at high oxide coverage. Structural and chemical analyses reveal that incomplete plasma conversion at high ATTT and low power leaves sulfur-rich species that are prone to oxidation, whereas high power promotes sulfur-vacancy formation and W-rich surfaces that preferentially evolve into WO x upon air exposure. Electrochemical measurements demonstrate that introducing WS2/WO x functionalities markedly enhances areal capacitance relative to bare CNWs. The WO x -dominant electrode delivered the highest areal capacitance among the tested electrodes, 91.1 mF cm–2 at 0.1 V s–1 and 21.7 mF cm–2 at 1.0 V s–1, compared with 4.6 and 3.15 mF cm–2 for bare CNW, respectively, although this gain was accompanied by increased interfacial and transport resistance. Dunn and impedance analyses reveal that this improvement arises primarily from increased diffusion-controlled pseudocapacitive charge storage, accompanied by a trade-off in the form of higher interfacial and transport resistance. This work elucidates how precursor loading and hydrogen-radical flux govern competitive sulfur- versus tungsten-centered oxidation pathways and provides a practical plasma-chemical framework for engineering high-performance, binder-free WS2/WO x @CNW hybrid electrodes for supercapacitor applications.
- 8 June 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (25) , 37284-37297
Open AccessPlasma-Chemical Integration of Solution-Derived ATTT with 3D Carbon Nanowalls for Controllable WS 2 /WO x Hybrid Supercapacitor Electrodes
Two-dimensional (2D) tungsten disulfide (WS2) has attracted considerable interest as a pseudocapacitive material, yet its practical application is often hindered by limited electrical conductivity, complex fabrication routes, and the need for binders. Here, we report a plasma-chemical route for fabricating binder-free, composition-tuned WS2/WO x @CNW hybrid electrodes from solution-deposited ammonium tetrathiotungstate (ATTT) with a downstream hydrogen remote plasma process. By systematically varying the ATTT concentration and microwave power, the surface chemistry of the CNW scaffold is controllably routed into CNW-dominant, WS2-rich, S-oxide-rich, and WO x -dominant regimes while preserving the overall three-dimensional CNW framework, despite partial surface masking at high oxide coverage. Structural and chemical analyses reveal that incomplete plasma conversion at high ATTT and low power leaves sulfur-rich species that are prone to oxidation, whereas high power promotes sulfur-vacancy formation and W-rich surfaces that preferentially evolve into WO x upon air exposure. Electrochemical measurements demonstrate that introducing WS2/WO x functionalities markedly enhances areal capacitance relative to bare CNWs. The WO x -dominant electrode delivered the highest areal capacitance among the tested electrodes, 91.1 mF cm–2 at 0.1 V s–1 and 21.7 mF cm–2 at 1.0 V s–1, compared with 4.6 and 3.15 mF cm–2 for bare CNW, respectively, although this gain was accompanied by increased interfacial and transport resistance. Dunn and impedance analyses reveal that this improvement arises primarily from increased diffusion-controlled pseudocapacitive charge storage, accompanied by a trade-off in the form of higher interfacial and transport resistance. This work elucidates how precursor loading and hydrogen-radical flux govern competitive sulfur- versus tungsten-centered oxidation pathways and provides a practical plasma-chemical framework for engineering high-performance, binder-free WS2/WO x @CNW hybrid electrodes for supercapacitor applications.
- 7 February 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (2)
Experimental analysis on effects of hydrogen addition on argon plasma jet at low vacuum
The effects of the addition of hydrogen on the properties of an argon plasma jet generated using a microwave plasma source under low-pressure conditions were experimentally investigated. Hydrogen was introduced at concentrations of 0.1%–1%, and the resulting changes in plasma jet characteristics were analyzed using optical emission spectroscopy (OES) and Langmuir probe (LP) measurements. The plasma jet length decreased significantly, and a reduction of over 60% occurred at a hydrogen concentration of 0.4% compared to that in pure argon plasma. The OES results indicated a reduction in Ar I intensities and a nonlinear trend in Hα and Hβ emission intensities. Based on LP measurements, decreases of 54% and 37% were observed in the electron temperature and plasma density, respectively, with 0.6% hydrogen addition. These effects are attributed to recombination reactions and interactions between argon and hydrogen species, which consume free electrons and metastable argon states.
- 7 February 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (2)
Experimental analysis on effects of hydrogen addition on argon plasma jet at low vacuum
The effects of the addition of hydrogen on the properties of an argon plasma jet generated using a microwave plasma source under low-pressure conditions were experimentally investigated. Hydrogen was introduced at concentrations of 0.1%–1%, and the resulting changes in plasma jet characteristics were analyzed using optical emission spectroscopy (OES) and Langmuir probe (LP) measurements. The plasma jet length decreased significantly, and a reduction of over 60% occurred at a hydrogen concentration of 0.4% compared to that in pure argon plasma. The OES results indicated a reduction in Ar I intensities and a nonlinear trend in Hα and Hβ emission intensities. Based on LP measurements, decreases of 54% and 37% were observed in the electron temperature and plasma density, respectively, with 0.6% hydrogen addition. These effects are attributed to recombination reactions and interactions between argon and hydrogen species, which consume free electrons and metastable argon states.
- Open Access
Microwave Plasma Assisted Aerosol Deposition (μ-PAD) for Ceramic Coating Applications
To improve plasma and chemical resistance on various vacuum components used for semiconductor manufacturing equipment, various ceramic coating techniques have been applied. Among these methods for ceramic coating, the well-known atmospheric plasma spray (APS) is advantageous for providing thick film (100 µm or more) deposition. However, there are problems associated with the phase transition of the coating film and poor film quality due to formation of voids. To solve these problems, the aerosol deposition (AD) method has been developed. This method provides nice ceramic film quality. However, the coating rate is quite slow and has difficulty producing thick films (>30 µm). To overcome these limitations, microwave plasma-assisted aerosol deposition (μ-PAD) is applied at low vacuum conditions without the AD nozzle. This method uses a microwave plasma source during the AD process. After enduring a long-term durability test, as a trial run, μ-PAD has been applied on the actual process site. With the Al2O3 powder, μ-PAD shows a coating rate that is 12 times higher than the AD method. In addition, the formation of a thicker film (96 µm) deposition has been demonstrated. On the other hand, the coating film hardness, porosity, adhesion, and withstand voltage characteristics were confirmed to be less than the AD method.
Open AccessMicrowave Plasma Assisted Aerosol Deposition (μ-PAD) for Ceramic Coating Applications
To improve plasma and chemical resistance on various vacuum components used for semiconductor manufacturing equipment, various ceramic coating techniques have been applied. Among these methods for ceramic coating, the well-known atmospheric plasma spray (APS) is advantageous for providing thick film (100 µm or more) deposition. However, there are problems associated with the phase transition of the coating film and poor film quality due to formation of voids. To solve these problems, the aerosol deposition (AD) method has been developed. This method provides nice ceramic film quality. However, the coating rate is quite slow and has difficulty producing thick films (>30 µm). To overcome these limitations, microwave plasma-assisted aerosol deposition (μ-PAD) is applied at low vacuum conditions without the AD nozzle. This method uses a microwave plasma source during the AD process. After enduring a long-term durability test, as a trial run, μ-PAD has been applied on the actual process site. With the Al2O3 powder, μ-PAD shows a coating rate that is 12 times higher than the AD method. In addition, the formation of a thicker film (96 µm) deposition has been demonstrated. On the other hand, the coating film hardness, porosity, adhesion, and withstand voltage characteristics were confirmed to be less than the AD method.
- Open Access
- 8 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 1959
Scanning Deposition Method for Large-Area Diamond Film Synthesis Using Multiple Microwave Plasma Sources
The demand for synthetic diamonds and research on their use in next-generation semiconductor devices have recently increased. Microwave plasma chemical vapor deposition (MPCVD) is considered one of the most promising techniques for the mass production of large-sized and high-quality single-, micro- and nanocrystalline diamond films. Although the low-pressure resonant cavity MPCVD method can synthesize high-quality diamonds, improvements are needed in terms of the resulting area. In this study, a large-area diamond synthesis method was developed by arranging several point plasma sources capable of processing a small area and scanning a wafer. A unit combination of three plasma sources afforded a diamond film thickness uniformity of ±6.25% at a wafer width of 70 mm with a power of 700 W for each plasma source. Even distribution of the diamond grains in a size range of 0.1–1 μm on the thin-film surface was verified using field-emission scanning electron microscopy. Therefore, the proposed novel diamond synthesis method can be theoretically expanded to achieve large-area films.
- 8 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 1959
Open AccessScanning Deposition Method for Large-Area Diamond Film Synthesis Using Multiple Microwave Plasma Sources
The demand for synthetic diamonds and research on their use in next-generation semiconductor devices have recently increased. Microwave plasma chemical vapor deposition (MPCVD) is considered one of the most promising techniques for the mass production of large-sized and high-quality single-, micro- and nanocrystalline diamond films. Although the low-pressure resonant cavity MPCVD method can synthesize high-quality diamonds, improvements are needed in terms of the resulting area. In this study, a large-area diamond synthesis method was developed by arranging several point plasma sources capable of processing a small area and scanning a wafer. A unit combination of three plasma sources afforded a diamond film thickness uniformity of ±6.25% at a wafer width of 70 mm with a power of 700 W for each plasma source. Even distribution of the diamond grains in a size range of 0.1–1 μm on the thin-film surface was verified using field-emission scanning electron microscopy. Therefore, the proposed novel diamond synthesis method can be theoretically expanded to achieve large-area films.
- 1 June 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (6) , 063304
Ion beam figuring with focused anode layer thruster
This work presents the peculiarities of cone ion beam formation with a focused thruster with anode layer (TAL) and its application to silicon carbide (SiC) ion beam figuring. Modeling results of Lorentz E × B force distribution in the discharge gap are presented. 3D particle tracing for keV Ar ions is carried out for the first time in the beam drift region of TAL with magnetic lens. Extracted ion beam full width at half maxima is about 2 mm in the focal plane, where the SiC etching rate reaches 0.5 µm/min. The SiC sputter yields are measured as a function of the Ar ion impact energy and beam incidence angle. The maximum sputter yield of 2.8 atom/ion is observed at 45° of the beam-sample angle for the Si targets. Furthermore, the maximum sputter yield value of 1.7 atom/ion is measured at 30° of the beam-sample angle for the SiC targets. The novelty of present research is in the application of focused TAL keV Ar ion beam to the SiC ion beam figuring.
- 1 June 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (6) , 063304
Ion beam figuring with focused anode layer thruster
This work presents the peculiarities of cone ion beam formation with a focused thruster with anode layer (TAL) and its application to silicon carbide (SiC) ion beam figuring. Modeling results of Lorentz E × B force distribution in the discharge gap are presented. 3D particle tracing for keV Ar ions is carried out for the first time in the beam drift region of TAL with magnetic lens. Extracted ion beam full width at half maxima is about 2 mm in the focal plane, where the SiC etching rate reaches 0.5 µm/min. The SiC sputter yields are measured as a function of the Ar ion impact energy and beam incidence angle. The maximum sputter yield of 2.8 atom/ion is observed at 45° of the beam-sample angle for the Si targets. Furthermore, the maximum sputter yield value of 1.7 atom/ion is measured at 30° of the beam-sample angle for the SiC targets. The novelty of present research is in the application of focused TAL keV Ar ion beam to the SiC ion beam figuring.
- Open Access
- 29 June 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (7) , 1705
Characteristics of Plasma Flow for Microwave Plasma Assisted Aerosol Deposition
To validate the possibility of the developed microwave plasma source with a novel structure for plasma aerosol deposition, the characteristics of the plasma flow velocity generated from the microwave plasma source were investigated by a Mach probe with pressure variation. Simulation with the turbulent model was introduced to deduce calibration factor of the Mach probe and to compare experimental measurements for analyses of collisional plasma conditions. The results show calibration factor does not seem to be a constant parameter and highly dependent on the collision parameter. The measured plasma flow velocity, which witnessed fluctuations produced by a shock flow, was between 400 and 700 m/s. The optimized conditions for microwave plasma assisted aerosol deposition were derived by the results obtained from analyses of the parameters of microwave plasma jet. Under the optimized conditions, Y2O3 coatings deposited on an aluminum substrate were investigated using scanning electron microscope. The results presented in this study show the microwave plasma assisted aerosol deposition with the developed microwave plasma source is highly feasible for thick films with >50 μm.
- 29 June 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (7) , 1705
Open AccessCharacteristics of Plasma Flow for Microwave Plasma Assisted Aerosol Deposition
To validate the possibility of the developed microwave plasma source with a novel structure for plasma aerosol deposition, the characteristics of the plasma flow velocity generated from the microwave plasma source were investigated by a Mach probe with pressure variation. Simulation with the turbulent model was introduced to deduce calibration factor of the Mach probe and to compare experimental measurements for analyses of collisional plasma conditions. The results show calibration factor does not seem to be a constant parameter and highly dependent on the collision parameter. The measured plasma flow velocity, which witnessed fluctuations produced by a shock flow, was between 400 and 700 m/s. The optimized conditions for microwave plasma assisted aerosol deposition were derived by the results obtained from analyses of the parameters of microwave plasma jet. Under the optimized conditions, Y2O3 coatings deposited on an aluminum substrate were investigated using scanning electron microscope. The results presented in this study show the microwave plasma assisted aerosol deposition with the developed microwave plasma source is highly feasible for thick films with >50 μm.