Khaled A. Mahafzah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Khaled A. Mahafzah has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad A. Obeidat
Tafila Technical University
7 shared publications - Ali Qasem Al-Shetwi
Fahad Bin Sultan University
5 shared publications - Ayman M. Mansour
Tafila Technical University
3 shared publications - Eleonora Riva Sanseverino
Department of Engineering, University of Palermo, 90128 Palermo, Italy
2 shared publications - Mahammad Abdul Hannan
School of Engineering and Technology, Sunway University, Bandar Sunway, Petaling Jaya 47500, Malaysia
2 shared publications - Taha Selim Ustun
Fukushima Renewable Energy Institute, AIST, Koriyama, Japan
2 shared publications
Latest Publications
- 1 October 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (20) , 205332
Enhanced Ćuk converter topology with dual switches and switched LC cells for high-gain low-power brushless DC motor drives
This paper proposes a new high-gain DC-DC converter based on the Ćuk converter. The proposed converter consists of two MOSFETs, two diodes, four inductors, and three capacitors. The coupling stage employs switched-inductor and switched-capacitor cells. In this configuration, the switched capacitors play an important role in energy transfer to the load. The proposed converter offers several advantages, including high voltage gain with inverted polarity, low voltage stress across semiconductor devices, and a low-rated voltage across the coupling capacitors (which does not exceed the DC input voltage), thereby enabling a reduction in PCB size. The topology achieves a theoretical voltage gain of (3-D)/(1-D), which represents a threefold improvement over the conventional Ćuk converter at a 75% duty cycle. The converter operates in continuous conduction mode with a fixed duty cycle and constant switching frequency to demonstrate its effectiveness. Analytical expressions for currents, voltages, duty cycle, and voltage gain are derived to explain the various operating modes in detail. The proposed converter is simulated using LTspice, which utilizes component models based on actual datasheets, providing more realistic waveform results. A 45 W, 12 V input, 20 kHz converter is designed and simulated; for a 75% duty cycle, the ideal output voltage predicted by the analysis is −108 V, whereas the simulated output voltage is approximately −102 V. The results show that, under the same operating conditions, the efficiency of the suggested converter is estimated, using a loss model of the semiconductor devices, to be 89.4% at rated load conditions, which is higher than that of the conventional Ćuk converter (85.7% at the same rated load conditions). Using the devices available in the laboratory, a prototype (12 V input, 430 Hz, −106 V output at approximately 56 W) was constructed to validate the voltage-conversion behavior of the converter. Because a calibrated power analyzer was not available, the efficiency of the prototype was not measured. In addition to its evaluation under static-load conditions, the proposed converter is evaluated as the DC-link power-conversion stage of a BLDC motor drive supplied through a three-phase VSI. The dynamic-load results demonstrate the converter’s ability to maintain a stable output voltage while supplying the BLDC motor drive.
- 1 October 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (20) , 205332
Enhanced Ćuk converter topology with dual switches and switched LC cells for high-gain low-power brushless DC motor drives
This paper proposes a new high-gain DC-DC converter based on the Ćuk converter. The proposed converter consists of two MOSFETs, two diodes, four inductors, and three capacitors. The coupling stage employs switched-inductor and switched-capacitor cells. In this configuration, the switched capacitors play an important role in energy transfer to the load. The proposed converter offers several advantages, including high voltage gain with inverted polarity, low voltage stress across semiconductor devices, and a low-rated voltage across the coupling capacitors (which does not exceed the DC input voltage), thereby enabling a reduction in PCB size. The topology achieves a theoretical voltage gain of (3-D)/(1-D), which represents a threefold improvement over the conventional Ćuk converter at a 75% duty cycle. The converter operates in continuous conduction mode with a fixed duty cycle and constant switching frequency to demonstrate its effectiveness. Analytical expressions for currents, voltages, duty cycle, and voltage gain are derived to explain the various operating modes in detail. The proposed converter is simulated using LTspice, which utilizes component models based on actual datasheets, providing more realistic waveform results. A 45 W, 12 V input, 20 kHz converter is designed and simulated; for a 75% duty cycle, the ideal output voltage predicted by the analysis is −108 V, whereas the simulated output voltage is approximately −102 V. The results show that, under the same operating conditions, the efficiency of the suggested converter is estimated, using a loss model of the semiconductor devices, to be 89.4% at rated load conditions, which is higher than that of the conventional Ćuk converter (85.7% at the same rated load conditions). Using the devices available in the laboratory, a prototype (12 V input, 430 Hz, −106 V output at approximately 56 W) was constructed to validate the voltage-conversion behavior of the converter. Because a calibrated power analyzer was not available, the efficiency of the prototype was not measured. In addition to its evaluation under static-load conditions, the proposed converter is evaluated as the DC-link power-conversion stage of a BLDC motor drive supplied through a three-phase VSI. The dynamic-load results demonstrate the converter’s ability to maintain a stable output voltage while supplying the BLDC motor drive.
- Open Access
- 4 February 2026
- Published by Acadlore Publishing Services Limited in International Journal of Transport Development and Integration
- Vol. 10 (1) , 76-92
Design, Modeling, and Control of a Ćuk based DC-DC Converter for Hybrid Vehicle Applications
- 4 February 2026
- Published by Acadlore Publishing Services Limited in International Journal of Transport Development and Integration
- Vol. 10 (1) , 76-92
Open AccessDesign, Modeling, and Control of a Ćuk based DC-DC Converter for Hybrid Vehicle Applications
- Open Access
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 39 (3) , 1499-1513
An improved hybrid AC to DC converter suitable for electric vehicles applications
This paper introduces a novel hybrid AC-DC converter designed for various applications like DC micro-grids, Electric Vehicle setups, and the integration of renewable energy resources into electric grids. The suggested hybrid converter involves a diode bridge rectifier, two interconnected single ended primary inductor converter (SEPIC) and Flyback converters, and two additional auxiliary controlled switches. These extra switches facilitate switching between SEPIC, Flyback, or a combination of both. The paper ex-tensively discusses the operational modes using mathematical equations, deriving specific duty cycles for each switch based on the circuit parameters. This hybrid converter aims to decrease total harmonic distortion (THD) in the line current. The findings exhibit a THD of approximately 14.51%, showcasing a 3% reduction compared to prior hybrid converters, thereby enhancing the power factor of the line current. Furthermore, at rated load conditions, the proposed converter achieves 90% efficiency. To validate the proposed hybrid converter’s functionality, a 4.5 kW converter is simulated and performed using MATLAB/Simulink after configuring the appropriate passive parameters.
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 39 (3) , 1499-1513
Open AccessAn improved hybrid AC to DC converter suitable for electric vehicles applications
This paper introduces a novel hybrid AC-DC converter designed for various applications like DC micro-grids, Electric Vehicle setups, and the integration of renewable energy resources into electric grids. The suggested hybrid converter involves a diode bridge rectifier, two interconnected single ended primary inductor converter (SEPIC) and Flyback converters, and two additional auxiliary controlled switches. These extra switches facilitate switching between SEPIC, Flyback, or a combination of both. The paper ex-tensively discusses the operational modes using mathematical equations, deriving specific duty cycles for each switch based on the circuit parameters. This hybrid converter aims to decrease total harmonic distortion (THD) in the line current. The findings exhibit a THD of approximately 14.51%, showcasing a 3% reduction compared to prior hybrid converters, thereby enhancing the power factor of the line current. Furthermore, at rated load conditions, the proposed converter achieves 90% efficiency. To validate the proposed hybrid converter’s functionality, a 4.5 kW converter is simulated and performed using MATLAB/Simulink after configuring the appropriate passive parameters.
- Top Cited Papers
- 10 October 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 478
Feasibility of future transition to 100% renewable energy: Recent progress, policies, challenges, and perspectives
- 10 October 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 478
Top Cited PapersFeasibility of future transition to 100% renewable energy: Recent progress, policies, challenges, and perspectives
- Open Access
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (3) , 2522-2532
An improved modulation technique suitable for a three level flying capacitor multilevel inverter
This research paper introduces an innovative modulation technique for controlling a 3-level flying capacitor multilevel inverter (FCMLI), aiming to streamline the modulation process in contrast to conventional methods. The proposed simplified modulation technique paves the way for more straightforward and efficient control of multilevel inverters, enabling their widespread adoption and integration into modern power electronic systems. Through the amalgamation of sinusoidal pulse width modulation (SPWM) with a high-frequency square wave pulse, this controlling technique attains energy equilibrium across the coupling capacitor. The modulation scheme incorporates a simplified switching pattern and a decreased count of voltage references, thereby simplifying the control algorithm.
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (3) , 2522-2532
Open AccessAn improved modulation technique suitable for a three level flying capacitor multilevel inverter
This research paper introduces an innovative modulation technique for controlling a 3-level flying capacitor multilevel inverter (FCMLI), aiming to streamline the modulation process in contrast to conventional methods. The proposed simplified modulation technique paves the way for more straightforward and efficient control of multilevel inverters, enabling their widespread adoption and integration into modern power electronic systems. Through the amalgamation of sinusoidal pulse width modulation (SPWM) with a high-frequency square wave pulse, this controlling technique attains energy equilibrium across the coupling capacitor. The modulation scheme incorporates a simplified switching pattern and a decreased count of voltage references, thereby simplifying the control algorithm.
- Open Access
- 8 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (6) , 2274
A New Smart Grid Hybrid DC–DC Converter with Improved Voltage Gain and Synchronized Multiple Outputs
This paper introduces a new hybrid DC–DC converter with enhanced voltage gain and synchronized multiple output capabilities, specifically tailored for smart grid applications. The proposed converter is based on the integration of non-isolated Zeta and Mahafzah converters, comprising a single controlled switch, two diodes, three inductors, and two coupling capacitors. The primary objective of this novel hybrid converter is to improve voltage gain as compared to conventional Zeta and Mahafzah topologies. By achieving higher voltage gain at lower duty cycles, the converter effectively reduces voltage stress on semiconductor switches and output diodes, thereby enhancing overall performance and reliability. A comprehensive examination of the hybrid converter’s operating principle is presented, along with detailed calculations of duty cycle and switching losses. The paper also explores the converter’s application in smart grids, specifically in the context of renewable energy systems and electric vehicles. Two distinct scenarios are analyzed to evaluate the converter’s efficacy. Firstly, the converter is assessed as a DC–DC converter for renewable energy systems, highlighting its relevance in sustainable energy applications. Secondly, the converter is evaluated as an electric vehicle adapter, showcasing its potential in the transportation sector. To validate the converter’s performance, extensive simulations are carried out using MATLAB/SIMULINK with parameters set at 25 kW, 200 V, and 130 A. The simulation results demonstrate the converter’s ability to efficiently supply multiple loads with opposing energy flows, making it a promising technology for optimized grid management and energy distribution. Moreover, the paper investigates the total harmonic distortion (THD) of the grid current, focusing on its impact in smart grid environments. Notably, the new hybrid converter topology achieves a THD of 21.11% for the grid current, indicating its ability to effectively mitigate harmonics and improve power quality. Overall, this research introduces a cutting-edge hybrid DC–DC converter that enhances voltage gain and synchronizes multiple outputs, specifically catering to the requirements of smart grid applications. The findings underscore the converter’s potential to significantly contribute to the advancement of efficient and resilient power conversion technologies for smart grids, enabling seamless integration of renewable energy systems and electric vehicles into the grid.
- 8 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (6) , 2274
Open AccessA New Smart Grid Hybrid DC–DC Converter with Improved Voltage Gain and Synchronized Multiple Outputs
This paper introduces a new hybrid DC–DC converter with enhanced voltage gain and synchronized multiple output capabilities, specifically tailored for smart grid applications. The proposed converter is based on the integration of non-isolated Zeta and Mahafzah converters, comprising a single controlled switch, two diodes, three inductors, and two coupling capacitors. The primary objective of this novel hybrid converter is to improve voltage gain as compared to conventional Zeta and Mahafzah topologies. By achieving higher voltage gain at lower duty cycles, the converter effectively reduces voltage stress on semiconductor switches and output diodes, thereby enhancing overall performance and reliability. A comprehensive examination of the hybrid converter’s operating principle is presented, along with detailed calculations of duty cycle and switching losses. The paper also explores the converter’s application in smart grids, specifically in the context of renewable energy systems and electric vehicles. Two distinct scenarios are analyzed to evaluate the converter’s efficacy. Firstly, the converter is assessed as a DC–DC converter for renewable energy systems, highlighting its relevance in sustainable energy applications. Secondly, the converter is evaluated as an electric vehicle adapter, showcasing its potential in the transportation sector. To validate the converter’s performance, extensive simulations are carried out using MATLAB/SIMULINK with parameters set at 25 kW, 200 V, and 130 A. The simulation results demonstrate the converter’s ability to efficiently supply multiple loads with opposing energy flows, making it a promising technology for optimized grid management and energy distribution. Moreover, the paper investigates the total harmonic distortion (THD) of the grid current, focusing on its impact in smart grid environments. Notably, the new hybrid converter topology achieves a THD of 21.11% for the grid current, indicating its ability to effectively mitigate harmonics and improve power quality. Overall, this research introduces a cutting-edge hybrid DC–DC converter that enhances voltage gain and synchronizes multiple outputs, specifically catering to the requirements of smart grid applications. The findings underscore the converter’s potential to significantly contribute to the advancement of efficient and resilient power conversion technologies for smart grids, enabling seamless integration of renewable energy systems and electric vehicles into the grid.
- 30 June 2023
- Published by International Information and Engineering Technology Association in Journal Européen des Systèmes Automatisés
- Vol. 56 (3) , 409-414
Improved Frequency Response of Parallel Virtual Synchronous Generators Using Grey Wolf Optimization
- 30 June 2023
- Published by International Information and Engineering Technology Association in Journal Européen des Systèmes Automatisés
- Vol. 56 (3) , 409-414
Improved Frequency Response of Parallel Virtual Synchronous Generators Using Grey Wolf Optimization
- Open Access
- 1 June 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 14 (2) , 898-908
A novel step-up/step-down DC-DC converter based on flyback and SEPIC topologies with improved voltage gain
A novel step-up/step-down DC-DC converter with improved voltage gain characteristics is suggested in this paper. The proposed converter combines flyback and single-ended primary inductance converter (SEPIC) converters. The voltage control loop design is simplified due to the use of only a single controlled switch. It has been discussed how switch duty cycle affects voltage gain. This relationship demonstrates that the proposed converter voltage gain is improved compared with flyback and SEPIC converters. However, compared to flyback and SEPIC converters, it has a higher voltage gain at any given duty cycle. The proposed converter operation is thoroughly discussed, the associated equations are derived, and its parameters are expertly designed. Moreover, it is designed to supply a DC load of 2.5 kW, 500 V, and 5 A. The proposed converter efficiency exceeds 84% under rated load conditions. Additionally, it is also presented as an adapter for electric vehicles. The waveforms associated with the simulation of the converter across the universal line voltage of 110-260 Vrms are shown. At both line voltages, the total harmonics distortions (THDs) of the line current are 17.12% and 27.26%, respectively. MATLAB/Simulink is utilized for validation in order to validate the topology for different applications.
- 1 June 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 14 (2) , 898-908
Open AccessA novel step-up/step-down DC-DC converter based on flyback and SEPIC topologies with improved voltage gain
A novel step-up/step-down DC-DC converter with improved voltage gain characteristics is suggested in this paper. The proposed converter combines flyback and single-ended primary inductance converter (SEPIC) converters. The voltage control loop design is simplified due to the use of only a single controlled switch. It has been discussed how switch duty cycle affects voltage gain. This relationship demonstrates that the proposed converter voltage gain is improved compared with flyback and SEPIC converters. However, compared to flyback and SEPIC converters, it has a higher voltage gain at any given duty cycle. The proposed converter operation is thoroughly discussed, the associated equations are derived, and its parameters are expertly designed. Moreover, it is designed to supply a DC load of 2.5 kW, 500 V, and 5 A. The proposed converter efficiency exceeds 84% under rated load conditions. Additionally, it is also presented as an adapter for electric vehicles. The waveforms associated with the simulation of the converter across the universal line voltage of 110-260 Vrms are shown. At both line voltages, the total harmonics distortions (THDs) of the line current are 17.12% and 27.26%, respectively. MATLAB/Simulink is utilized for validation in order to validate the topology for different applications.
- Open Access
- 24 May 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (11) , 8515
A New Cuk-Based DC-DC Converter with Improved Efficiency and Lower Rated Voltage of Coupling Capacitor
DC-DC converters play a crucial role in recent and advanced applications, enabling efficient power conversion and management for renewable energy systems, electric vehicles, portable devices, and advanced communication systems. In line with this, the objective of this paper is to introduce a new DC-DC configuration based on the Cuk converter named as Mahafzah converter, which utilizes a coupling capacitor with a lower rated voltage. The paper aims to demonstrate the effectiveness of the proposed converter in terms of improved efficiency, reduced size, and reduced semiconductor device currents compared to the conventional Cuk converter. The proposed configuration comprises the same components as the Cuk converter, but in a different arrangement, without any additional elements. The main advantage of the proposed converter is using a coupling capacitor with a much lower rated voltage than the Cuk converter, resulting in a smaller capacitor size, reduced printed circuit board (PCB) size, and manufacturing cost. Additionally, the proposed converter reduces the currents of the semiconductor devices compared to those in the Cuk converter. To demonstrate its effectiveness, the converter is operated under continuous current mode (CCM) with a constant duty cycle and switching frequency. The study provides an in-depth discussion of the various operating modes by making use of equations relating to currents, voltages, duty cycles, and voltage gains. It also provides detailed illustrations of the limits between CCM and discontinuous current mode (DCM). The effectiveness of the proposed converter is demonstrated through a design example with operating parameters of 1 kW, 200 V/−300 V, and 20 kHz. Additionally, a low voltage–low power prototype (12/−18 V, 3.24 W, 20 kHz) is established to verify the operation of the proposed converter. Simulation and experimental verification of the proposed configuration achieved the desired results to improve efficiency and reduce the rate. The results clearly indicate that the efficiency of the proposed converter surpasses that of the conventional Cuk converter under identical operating conditions, reaching approximately 88% at rated load conditions.
- 24 May 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (11) , 8515
Open AccessA New Cuk-Based DC-DC Converter with Improved Efficiency and Lower Rated Voltage of Coupling Capacitor
DC-DC converters play a crucial role in recent and advanced applications, enabling efficient power conversion and management for renewable energy systems, electric vehicles, portable devices, and advanced communication systems. In line with this, the objective of this paper is to introduce a new DC-DC configuration based on the Cuk converter named as Mahafzah converter, which utilizes a coupling capacitor with a lower rated voltage. The paper aims to demonstrate the effectiveness of the proposed converter in terms of improved efficiency, reduced size, and reduced semiconductor device currents compared to the conventional Cuk converter. The proposed configuration comprises the same components as the Cuk converter, but in a different arrangement, without any additional elements. The main advantage of the proposed converter is using a coupling capacitor with a much lower rated voltage than the Cuk converter, resulting in a smaller capacitor size, reduced printed circuit board (PCB) size, and manufacturing cost. Additionally, the proposed converter reduces the currents of the semiconductor devices compared to those in the Cuk converter. To demonstrate its effectiveness, the converter is operated under continuous current mode (CCM) with a constant duty cycle and switching frequency. The study provides an in-depth discussion of the various operating modes by making use of equations relating to currents, voltages, duty cycles, and voltage gains. It also provides detailed illustrations of the limits between CCM and discontinuous current mode (DCM). The effectiveness of the proposed converter is demonstrated through a design example with operating parameters of 1 kW, 200 V/−300 V, and 20 kHz. Additionally, a low voltage–low power prototype (12/−18 V, 3.24 W, 20 kHz) is established to verify the operation of the proposed converter. Simulation and experimental verification of the proposed configuration achieved the desired results to improve efficiency and reduce the rate. The results clearly indicate that the efficiency of the proposed converter surpasses that of the conventional Cuk converter under identical operating conditions, reaching approximately 88% at rated load conditions.
- Open Access
- 9 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 16504
Artificial-Intelligence-Based Open-Circuit Fault Diagnosis in VSI-Fed PMSMs and a Novel Fault Recovery Method
Artificial intelligence (AI) techniques are widely used in fault diagnosis because they are superior in detection and prediction. The detection of faults in power systems containing electronic components is critical. The switch faults of the voltage source inverter (VSI) have a severe impact on the driving system. Short-circuit switches increase the thermal stress due to their fast and high stator currents. Additionally, open-circuit switches cause unstable motor operation. However, these issues are not sufficiently addressed or accurately predicted for VSI switch faults in the literature. Thus, this paper investigates the use of different AI classifiers for three-phase VSI fault diagnosis. Various AI methods are used, such as naïve Bayes, support vector machine (SVM), artificial neural network (ANN), and decision tree (DT) techniques. These methods are applied to a VSI-fed permanent magnet synchronous motor (PMSM) to detect the faults in the inverter switches. These methods use the drain–source voltage and PWM signals to decide whether the switch is healthy or unhealthy. In addition, they are compared in terms of their detection accuracy. In this regard, the comparative results show that the DT method has the highest accuracy as compared to other methods in the fault diagnosis process. Moreover, this paper proposes a novel and universal voltage compensation loop to compensate for the absence of the voltage portion due to the open switch fault. Thus, the driving system is assisted in operating under its normal operating conditions. The universal term is used because the proposed voltage compensation loop can be implemented in any type of inverter. To validate the results, the proposed system is implemented using two software programs, LTSPICE XVII-USA, WEKA 3.9-New Zealand.
- 9 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 16504
Open AccessArtificial-Intelligence-Based Open-Circuit Fault Diagnosis in VSI-Fed PMSMs and a Novel Fault Recovery Method
Artificial intelligence (AI) techniques are widely used in fault diagnosis because they are superior in detection and prediction. The detection of faults in power systems containing electronic components is critical. The switch faults of the voltage source inverter (VSI) have a severe impact on the driving system. Short-circuit switches increase the thermal stress due to their fast and high stator currents. Additionally, open-circuit switches cause unstable motor operation. However, these issues are not sufficiently addressed or accurately predicted for VSI switch faults in the literature. Thus, this paper investigates the use of different AI classifiers for three-phase VSI fault diagnosis. Various AI methods are used, such as naïve Bayes, support vector machine (SVM), artificial neural network (ANN), and decision tree (DT) techniques. These methods are applied to a VSI-fed permanent magnet synchronous motor (PMSM) to detect the faults in the inverter switches. These methods use the drain–source voltage and PWM signals to decide whether the switch is healthy or unhealthy. In addition, they are compared in terms of their detection accuracy. In this regard, the comparative results show that the DT method has the highest accuracy as compared to other methods in the fault diagnosis process. Moreover, this paper proposes a novel and universal voltage compensation loop to compensate for the absence of the voltage portion due to the open switch fault. Thus, the driving system is assisted in operating under its normal operating conditions. The universal term is used because the proposed voltage compensation loop can be implemented in any type of inverter. To validate the results, the proposed system is implemented using two software programs, LTSPICE XVII-USA, WEKA 3.9-New Zealand.