ASAhmad Indra Siswantara

Ahmad Indra Siswantara

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ahmad Indra Siswantara has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigating Kinetic and Thermodynamic Parameters in the Pyrolysis of Sheep Manure Using Thermogravimetric Analysis

    by Ahmad Indra Siswantara, Illa Rizianiza, Diyas Prawara Mahdi, Tanwir Ahmad Farhan, Candra Damis Widiawati, Muhamad Hilman Gumelar Syafei, Adi Syuriadi


  • Open Access

    Identifying the influence of inlet velocity changes to pressure drop and collecting efficiency in Stairmand and Lapple type cyclone separators

    by Adi Syuriadi, Ahmad Indra Siswantara, Ridho Irwansyah, Supriyadi Supriyadi, Candra Damis Widiawaty, Muhammad Hilman Gumelar Syafei, Illa Rizianiza, Sulaksana Permana, Iwan Susanto

    The object of this research is to compare the performance of Stairmand and Lapple type cyclone separators. The main problem to be solved in this research is determining which Stairmand or Lapple type cyclone separator is more suitable for integration into the pyrolysis system. The comparison is based on key performance indicators: pressure drop and collecting efficiency. The research findings indicate that both Stairmand and Lapple cyclone separators exhibit similar trends in pressure drop and collecting efficiency. As inlet velocity increases, the pressure drop also increases for both types. However, the collecting efficiency initially rises but then declines when inlet velocities exceed 13 m/s. The Lapple variant achieved a peak collecting efficiency of 98.94 % and pressure drop 16.26 mbar at an inlet velocity of 13 m/s, whereas the Stairmand design reached 97.33 % and pressure drop 12.16 mbar at 13 m/s inlet velocity. The Lapple type cyclone separator outperformed the Stairmand type in terms of both of pressure drop and collecting efficiency. This superiority is attributed to the specific design features and characteristics of the Lapple type. The superior performance of the Lapple type cyclone separator can be explained by its unique design elements that contribute to improved particulate matter separation and pressure drop. These elements may include differences in cylinder height and particulate matter outlet diameter. Based on the findings of this research, the Lapple type cyclone separator is recommended for integration into pyrolysis systems. However, it is important to consider the specific operating conditions of the pyrolysis process, such as temperature, the particulate matter size distribution, flow rate, and desired separation efficiency

  • Open Access

    Identifying the influence of blade number and angle of attack on a breastshot type waterwheel micro hydroelectric power generator using ANOVA

    by Adi Syuriadi, Ahmad Indra Siswantara, Dewin Purnama, Gun Gun Ramdlan Gunadi, Iwan Susanto, Sulaksana Permana

    This study focuses on optimizing the performance of micro-hydro power generation, specifically the breastshot type waterwheel. The limited availability of non-renewable energy sources and the high cost of developing renewable energy sources in the energy sector pose challenges, making it essential to find new energy sources and improve energy efficiency. The 2004–2022 national electricity plan aims to increase electricity access in rural areas, including remote regions like Bogor Regency, where access to electricity is limited. Many residents have constructed their own micro hydroelectric power generators, but their vulnerability to natural disasters is a concern. The study investigates the potential of breastshot waterwheel technology for micro hydroelectric power generation. The study involved testing a micro hydro power plant with 6, 8, and 10 blades and blade angles of 0°, 30°, and 45°. The current research focuses on performance optimization, including the use of ANOVA analysis to know the significant impact of blade number and angle on the waterwheel’s rotation. The maximum rotational speed was achieved with 10 blades and an angle of attack of 0°, 30°, and 45°, with respective speeds of 153.59 RPM, 155.84 RPM, and 164.95 RPM. The study indicates that the higher the number and angle of attack of blades, the greater the rotation of the breastshot type waterwheel. ANOVA tests showed that the number of blades had a significant impact on the waterwheel’s rotation, with an F-test value of 6.32 and a p-value of 0.012. On the other hand, the angle of attack of the blade had no significant impact, with an F-test value of 3.20 and a p-value of 0.067


  • Open Access

    Flow distribution analysis of a novel fcc system through experiment study and atomic model

    by Ahmad Indra Siswantara, M. Hilman Gumelar Syafei, Muhammad Arif Budiyanto, Candra Damis Widiawaty, Adi Syuriadi, Tanwir Ahmad Farhan, Sulaksana Permana

    As the largest palm oil producer in the world, Indonesia has a promising potential to produce green fuel through the Fluid Catalytic Cracking (FCC) process. A novel FCC configuration, FCC Proto X 3, which combines a riser reactor and downer reactor in the system, has been developed. However, several valves including in the FCC system remain a black box to the flow distribution in the system. The objective of this paper is to investigate the effect of the valve setting variation on the airflow distribution of the FCC system. The methodology uses experiment and acausal modeling. The effect of valve setting variation on pressure and average velocity of the airflow has been investigated. The experiment is conducted under cold test conditions, while the acausal model of the FCC system is built by using OpenModelica. It is obtained that valve 2 which controls the flow at the channel toward the regenerator is essential due to its role in controlling the air supply combustion process in the regenerator and driving the spent catalyst particles to the regenerator. Valve 3 is responsible for controlling the flow toward the riser reactor directly. Later, it is responsible for supplying the lifting fluid to support the catalytic cracking reaction at the riser sections. Valve 4 contributes to controlling the lifting fluid to the downer reactor. It will also be responsible for supplying thermal energy from the high-temperature particle catalyst to the reactor. When all valves toward the regenerator and reactor are 100 % open, the measured average velocity at the flue gas outlet and the product outlet are 8.04 m/s and 5.775 m/s respectively. The result shows that the airflow at the FCC system tends to flow through the regenerator. The atomic model estimation also shows a similar trend to the experiment result


  • Open Access

    Identification of combustion regularities of fuel mixtures from Azolla biomass, goat manure biochar and goat manure bio-oil for FCC furnace

    by Tanwir Ahmad Farhan, Ahmad Indra Siswantara, Ahmad Syihan Auzani, Adi Syuriadi, Candra Damis Widiawaty, Muhammad Hilman Gumelar Syafei, Iwan Susanto

    Fluid catalytic cracking (FCC) is a method of cracking vegetable oils into simpler fractions and green fuel oils. One component of the FCC system is the FCC furnace. The FCC furnace is where the combustion process occurs and provides high heat transfer throughout the FCC system, especially for heating the reactor. The reactor temperature is the catalyst cracking temperature. The cracking temperature of the catalyst depends on the feed oil used in the cracking process, such as crude palm oil at 450‒550 °C or crude bio-oil at 300 °C. The fuel for heating an FCC furnace is usually coal. To reduce coal, we use a mixture of Azolla microphylla biomass with biochar and bio-oil from goat manure. The aim of this study was to analyze the mixture of Azolla microphylla biomass with biochar and bio-oil from goat manure to obtain sufficient furnace temperature to heat the FCC reactor, perform analytical calculations to obtain the volume of flue gas formed from the combustion reaction. We conducted two experiments; the first experiment used a mixture of 1 kg of Goat Manure Biochar (GMBC) with 0.5 kg of Azolla microphylla and the second experiment used a mixture of one kg of GMBC with 0.5 kg of Azolla microphylla plus 300 ml of Goat Manure Bio-oil (GMBO). A fuel mixture of one kilogram GMBC with 0.5 kg Azolla is not effective in combustion because the maximum temperature in the furnace is 177 °C but the fuel mixture of one kg GMBC, 0.5 kg Azolla and 300 ml GMBO has a furnace temperature of 472.75 °C, which can heat the stripper up to 313.25 °C so that cracking can occur in the raw bio-oil. Analysis of combustion results showed an increase in total CO2 volume from experiment one and experiment two of 0.966

  • Open Access

    Analysis of the effect of biomass variants (fish waste, tamanu waste and duckweed) on the characteristics of syngas, bio oil, and carbon charcoal produced in the pyrolysis process

    by Adi Syuriadi, Ahmad Indra Siswantara, Fadia Ramadhania Nurhakim, Yubdina Nurfazlia Irbah, Bagas Al Rizky, Fara Arinda Zulfa, Faisal Azizi Devitra, Sulaksana Permana, Iwan Susanto

    Biomass is one of the renewable energy sources that are often found around the Indonesia area. It can be converted into various forms of fuel by pyrolysis. Pyrolysis is a process of chemical decomposition of biomass through a heating process at high temperatures that occurs with no or little oxygen. The purpose of this study was to analyze the effect of the type of biomass on the characteristics of syngas, bio oil and carbon charcoal produced in pyrolysis. Syngas consisting of hydrogen and carbon monoxide can be used as raw materials for the chemical industry in addition to electrical energy, such as methanol, formic acid and ammonia industries. Bio-oil contains a number of chemical compounds that have the potential as raw materials for preservatives, antioxidants, disinfectants, or as biopesticides. Carbon charcoal is useful as an energy source, activated carbon with higher economic value such as catalysts, adsorbents, and supercapacitors. This research used an experimental method. Biomass comes from fish waste, tamanu waste, and duckweed. The parameters observed were temperature of 400–500 °C, for 30 minutes, and 150 grams biomass, in order to determine the duration of the syngas flame and the amount of bio-oil and carbon charcoal. The syngas produced from duckweed has a longer flame test with a time of 126 seconds with a blue flame while the syngas from tamanu waste produces a reddish blue flame for 18 seconds. On the other hand, the results of the bio-oil produced from fish waste, 19.1 grams are weightier than from duckweed, 3.2 grams. Then the most carbon charcoal is produced by tamanu waste weighing 141.9 grams while the least is produced by duckweed weighing 27.7 grams


  • Open Access

    Effects of the superficial gas velocity on the distribution of solid particles in the circulating fluidized bed using CFD simulations

    by A Daryus, A I Siswantara, B Budiarso, H Pujowidodo, G G R Gunadi

    The purpose of the study is to investigate the effects of various air flow rate or superficial gas velocity in term of excess air to obtain the optimum distribution of solid phase in the Circulating Fluidized Bed (CFB). The Computational Fluid Dynamics (CFD) method used for simulations uses the Multi-fluid Eulerian approaches incorporating the Kinetic Theory of Granular to calculate the motion of particles and the standard k-ॉ turbulence model to simulate the fluid flows. The simulations were carried out using five different air mass flow rates, based on the air consumption in the combustion of coal used in real CFB boiler operation. Since this simulation is the preliminary study of the particle dynamics in CFB, the combustion process had not simulated yet. In this work, the complex flow has been resolved by applying the CFDSOF commercial CFD software. The pressure on bed, the distribution of pressure, the particle velocity and volume fraction in the CFB were investigated to obtain the optimum results of the fluidization. The values of the pressure found from experiments at the bottom of bed was around 4,500 Pa, and the results from simulations were not different significantly with this values. At the excess air of 90%, the velocity of particles at the surface of bed is highest that can lead to the erosion on the firewall in long term operations, meanwhile at the lower excess air values, their velocity were relatively small. The optimum of excess air that found to be safe for boiler to operate was around 60% - 75% for average particle size 1 mm.