Cole D. Fincher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cole D. Fincher has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Yet-Ming Chiang
Massachusetts Institute of Technology
12 shared publications W. Craig Carter
Massachusetts Institute of Technology
6 shared publicationsBrian W. Sheldon
Brown University
4 shared publicationsColin Gilgenbach
Massachusetts Institute of Technology
4 shared publications- Andrew B. Li
Department of Mechanical Engineering
3 shared publications - Chiung-Yuan Lo
Department of Materials Science & Engineering
3 shared publications
Latest Publications
- Open Access
- 16 September 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Adaptive Voiding Enables Interfacial Morphological Control at Low Stack Pressure in Solid-State Batteries
Solid-state batteries with alkali metal anodes offer high energy density and improved safety, but their performance is hindered by void formation at the metal-solid electrolyte interface during metal stripping, leading to impedance rise and increased probability of dendrite formation upon plating. Here, we demonstrate that low concentrations (<5 vol%) of potassium metal added to industrial-grade lithium metal creates a dispersed Na-K liquid phase that suppresses voiding and enables stable, high-capacity stripping at practical current densities and stack pressures below 1 MPa. We furthermore identify a low-frequency oscillatory impedance attributed to “adaptive voiding”—the cyclic expansion and contraction of interfacial voids arising from an interplay between void growth and lithium deformation. This behavior, revealed by cryo-PFIB imaging and electrochemical analysis, offers a diagnostic signature for evaluating interfacial stability. These findings highlight new opportunities for designing robust, high-capacity SSBs operable under realistic mechanical constraints by controlling dynamic interfacial morphologies.
- 16 September 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessAdaptive Voiding Enables Interfacial Morphological Control at Low Stack Pressure in Solid-State Batteries
Solid-state batteries with alkali metal anodes offer high energy density and improved safety, but their performance is hindered by void formation at the metal-solid electrolyte interface during metal stripping, leading to impedance rise and increased probability of dendrite formation upon plating. Here, we demonstrate that low concentrations (<5 vol%) of potassium metal added to industrial-grade lithium metal creates a dispersed Na-K liquid phase that suppresses voiding and enables stable, high-capacity stripping at practical current densities and stack pressures below 1 MPa. We furthermore identify a low-frequency oscillatory impedance attributed to “adaptive voiding”—the cyclic expansion and contraction of interfacial voids arising from an interplay between void growth and lithium deformation. This behavior, revealed by cryo-PFIB imaging and electrochemical analysis, offers a diagnostic signature for evaluating interfacial stability. These findings highlight new opportunities for designing robust, high-capacity SSBs operable under realistic mechanical constraints by controlling dynamic interfacial morphologies.
- Top Cited Papers
- 25 March 2026
- Published by Springer Nature in Nature
- Vol. 652 (8111) , 906-911
Electrochemical corrosion accompanies dendrite growth in solid electrolytes
Charging rates, cycling performance and safety of solid-state batteries using metal negative electrodes are often limited by dendrites1,2,3, the growth of which depends on coupling between electrochemical and mechanical driving forces. Previously, it has been assumed that dendrites propagate when plating-induced stresses reach the fracture stress of the solid electrolyte. Here we show that dendrites can propagate at far lower stresses. Using operando birefringence microscopy4, we directly measure stresses around growing dendrites in garnet Li6.6La3Zr1.6Ta0.4O12, a highly stable solid electrolyte5,6,7. Plating-induced stresses are present throughout growth and approach the mechanical fracture stress for the slowest-growing dendrites. As current densities and dendrite velocities increase, the stresses accompanying dendrite growth surprisingly decrease, with dendrite propagation occurring at stresses up to 75% lower than under mechanical load alone. Cryogenic scanning transmission electron microscopy (STEM) of dendrites propagated at high current reveals electrolyte decomposition to new phases, associated with which is a net molar volume contraction. The electrochemically induced mode of embrittlement may be mitigated through understanding and control of the nature of phase transitions accompanying instability.
- 25 March 2026
- Published by Springer Nature in Nature
- Vol. 652 (8111) , 906-911
Top Cited PapersElectrochemical corrosion accompanies dendrite growth in solid electrolytes
Charging rates, cycling performance and safety of solid-state batteries using metal negative electrodes are often limited by dendrites1,2,3, the growth of which depends on coupling between electrochemical and mechanical driving forces. Previously, it has been assumed that dendrites propagate when plating-induced stresses reach the fracture stress of the solid electrolyte. Here we show that dendrites can propagate at far lower stresses. Using operando birefringence microscopy4, we directly measure stresses around growing dendrites in garnet Li6.6La3Zr1.6Ta0.4O12, a highly stable solid electrolyte5,6,7. Plating-induced stresses are present throughout growth and approach the mechanical fracture stress for the slowest-growing dendrites. As current densities and dendrite velocities increase, the stresses accompanying dendrite growth surprisingly decrease, with dendrite propagation occurring at stresses up to 75% lower than under mechanical load alone. Cryogenic scanning transmission electron microscopy (STEM) of dendrites propagated at high current reveals electrolyte decomposition to new phases, associated with which is a net molar volume contraction. The electrochemically induced mode of embrittlement may be mitigated through understanding and control of the nature of phase transitions accompanying instability.
- Open Access
- 13 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Adaptive Voiding Enables Interfacial Morphological Control at Low Stack Pressure in Solid-State Batteries
Solid-state batteries with alkali metal anodes offer high energy density and improved safety, but their performance is hindered by void formation at the metal-solid electrolyte interface during discharge. These voids lead to contact loss and impedance rise, and increase the probability of dendrite formation upon plating. While high stack pressures (≥1 MPa) can suppress voiding, they impose engineering constraints that reduce pack-level energy density. In this work, we demonstrate that adding low concentrations (<5 vol%) of potassium metal to industrial-grade lithium metal creates a dispersed Na-K liquid phase that suppresses voiding and enables stable, high-capacity stripping at practical current densities and stack pressures below 1 MPa. Additionally, we identify a low-frequency oscillatory impedance response which we attribute to "adaptive voiding"-the cyclic expansion and contraction of interfacial voids arising from the interplay of contact loss and stress-driven lithium deformation. This behavior, characterized by cryo-PFIB imaging and electrochemical analysis, offers a diagnostic signature for evaluating interfacial stability in alkali metal-solid electrolyte systems. These findings highlight new opportunities for designing robust, high-capacity solid-state batteries operable under realistic mechanical constraints by leveraging dynamic interfacial morphological control.
- 13 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessAdaptive Voiding Enables Interfacial Morphological Control at Low Stack Pressure in Solid-State Batteries
Solid-state batteries with alkali metal anodes offer high energy density and improved safety, but their performance is hindered by void formation at the metal-solid electrolyte interface during discharge. These voids lead to contact loss and impedance rise, and increase the probability of dendrite formation upon plating. While high stack pressures (≥1 MPa) can suppress voiding, they impose engineering constraints that reduce pack-level energy density. In this work, we demonstrate that adding low concentrations (<5 vol%) of potassium metal to industrial-grade lithium metal creates a dispersed Na-K liquid phase that suppresses voiding and enables stable, high-capacity stripping at practical current densities and stack pressures below 1 MPa. Additionally, we identify a low-frequency oscillatory impedance response which we attribute to "adaptive voiding"-the cyclic expansion and contraction of interfacial voids arising from the interplay of contact loss and stress-driven lithium deformation. This behavior, characterized by cryo-PFIB imaging and electrochemical analysis, offers a diagnostic signature for evaluating interfacial stability in alkali metal-solid electrolyte systems. These findings highlight new opportunities for designing robust, high-capacity solid-state batteries operable under realistic mechanical constraints by leveraging dynamic interfacial morphological control.
- Open Access
- 5 November 2025
- Published by Wiley in Advanced Materials
- Vol. 38 (16) , e12961
Reactive Carbide‐Based Synthesis and Microstructure of NASICON Sodium Metal All Solid‐State Electrolyte
Reactive carbide precursor‐based synthesis of NASICON‐type NZSP (Na 1+x Zr 2 Si x P 3‐x O 12 ) solid‐state electrolyte (SSE) is demonstrated, in contrast to the established oxide‐based approach. Exothermic decomposition of ZrC and SiC in air homogenizes microstructure, yielding 98% compact density after conventional sintering at 1200 °C. Quantitative stereology demonstrates that significant microstructural differences are present. Compacts of carbide‐derived Carb‐NZSP are 98% dense with a secondary zirconium oxide (ZrO 2 ) volume fraction of 0.2% ± 0.3%, versus 93% dense and 3% ± 1% for oxide‐derived baseline. For Carb‐NZSP, the secondary glassy phosphate phase is agglomerated, while for baseline, it is dispersed and percolated. Electrochemical testing combined with post‐mortem analysis demonstrates how microstructural control of secondary phases is critical for dendrite suppression: Carb‐NZSP critical current density (CCD) is 3.1 ± 0.8 mA cm − 2 at 0.1 mAh cm − 2 , versus 1.0 ± 0.7 mA cm −2 at 0.1 mAh cm −2 . Cryogenic focused ion beam (cryo‐FIB) analysis demonstrates that in both materials, the porous 2D sheet‐like sodium metal dendrites propagate around and subsume NZSP grains, likely following a path enriched with glassy phase and with porosity. Dendrites also flow around isolated zirconia particles. Phase field simulation reveals deflection of dendrites by mechanically tough zirconia, while brittle glassy phase accelerates dendrite growth, especially when finely distributed.
- 5 November 2025
- Published by Wiley in Advanced Materials
- Vol. 38 (16) , e12961
Open AccessReactive Carbide‐Based Synthesis and Microstructure of NASICON Sodium Metal All Solid‐State Electrolyte
Reactive carbide precursor‐based synthesis of NASICON‐type NZSP (Na 1+x Zr 2 Si x P 3‐x O 12 ) solid‐state electrolyte (SSE) is demonstrated, in contrast to the established oxide‐based approach. Exothermic decomposition of ZrC and SiC in air homogenizes microstructure, yielding 98% compact density after conventional sintering at 1200 °C. Quantitative stereology demonstrates that significant microstructural differences are present. Compacts of carbide‐derived Carb‐NZSP are 98% dense with a secondary zirconium oxide (ZrO 2 ) volume fraction of 0.2% ± 0.3%, versus 93% dense and 3% ± 1% for oxide‐derived baseline. For Carb‐NZSP, the secondary glassy phosphate phase is agglomerated, while for baseline, it is dispersed and percolated. Electrochemical testing combined with post‐mortem analysis demonstrates how microstructural control of secondary phases is critical for dendrite suppression: Carb‐NZSP critical current density (CCD) is 3.1 ± 0.8 mA cm − 2 at 0.1 mAh cm − 2 , versus 1.0 ± 0.7 mA cm −2 at 0.1 mAh cm −2 . Cryogenic focused ion beam (cryo‐FIB) analysis demonstrates that in both materials, the porous 2D sheet‐like sodium metal dendrites propagate around and subsume NZSP grains, likely following a path enriched with glassy phase and with porosity. Dendrites also flow around isolated zirconia particles. Phase field simulation reveals deflection of dendrites by mechanically tough zirconia, while brittle glassy phase accelerates dendrite growth, especially when finely distributed.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (8) , 1209
Direct Mechanical and Electrochemical Analysis of Dendrites in Solid-State Electrolytes
Although solid-state batteries with metal anodes promise to enable safer, higher energy density batteries, metal protrusions (dendrites) short-circuit the cell when charging faster than a critical current density.1,2It is generally believed that dendrites grow when the strain energy available for crack extension (the strain energy release rate, ) exceeds that required for fracture of the solid-electrolyte..2-4 We test this hypothesis using operando birefringence microscopy5 to directly observe dendrite-induced stresses. The strain energy release rate is determined by fitting the experimentally measured stress distribution to that which is expected in the vicinity of an internally loaded crack (detailed in Fig. 1).6 These operando experiments, combined with cryogenic scanning transmission electron microscopy (STEM) characterization of the dendrite tip, enable studies of electrochemical and mechanical phenomena underlying dendrite growth in ceramic electrolytes. All experiments were conducted on the most electrochemically stable Li-ion conducting solid electrolyte (tantalum-doped lithium lanthanum zirconium oxide). References: Sudworth, J. L., Hames, M. D., Storey, M. A., Azim, M. F. & Tilley, A. R. An analysis and laboratory assessment of Two Sodium Sulfur Cell Designs. Power Sources 4, 1–18 (1972). Sharafi, A. S. et al. Characterizing the Li–Li7La3Zr2O12 interface stability and kinetics as a function of temperature and current density. J. Power Sources 302, 135–139 (2016). Fincher, C. D. et al. Controlling dendrite propagation in solid-state batteries with engineered stress. Joule 6, 2794-2809 (2022). Porz†, L., Swamy†, T. et al. Mechanism of lithium metal penetration through inorganic solid electrolytes. Adv. Energy Mater. 7, 1701003 (2017). Athanasiou†, C. E., Fincher†, C. D. et al. Operando measurements of dendrite-induced stresses in ceramic electrolytes using photoelasticity. Matter (2023). Fincher C. D., et al. In prep. Figure 1: Operando birefringence imaging enables direct measurement of dendrite-induced stresses in solid-electrolytes. Pixel-by-pixel computational analysis allows measurement of the mechanical driving force for crack growth, (the strain energy release rate).6 (a) Dendrites are grown through the plane of a thin LLZO solid electrolyte which was mechanically thinned to the point of translucency. A microscope is used to collect (b) polarized light images of dendrite propagation, and (c) spatially resolved measurements of the max shear stress in the solid electrolyte. The stress measurements in (c) correspond to the region enclosed by the dashed black box in (b). The strain energy release rate is determined by fitting the experimentally determined stress field (c) to that expected analytically (d), using as a fitting parameter. (e) The stress distribution measured along a line profile starting at the crack tip and ending at a point 45° (in red) and 90° (in blue) from the propagation direction. The solid and dashed lines series represent data from the experimental and computed analytic stress fields in c and d, respectively. The end points of the 45° and 90° profiles are shown as red and blue “X” symbols in c and d, respectively. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (8) , 1209
Direct Mechanical and Electrochemical Analysis of Dendrites in Solid-State Electrolytes
Although solid-state batteries with metal anodes promise to enable safer, higher energy density batteries, metal protrusions (dendrites) short-circuit the cell when charging faster than a critical current density.1,2It is generally believed that dendrites grow when the strain energy available for crack extension (the strain energy release rate, ) exceeds that required for fracture of the solid-electrolyte..2-4 We test this hypothesis using operando birefringence microscopy5 to directly observe dendrite-induced stresses. The strain energy release rate is determined by fitting the experimentally measured stress distribution to that which is expected in the vicinity of an internally loaded crack (detailed in Fig. 1).6 These operando experiments, combined with cryogenic scanning transmission electron microscopy (STEM) characterization of the dendrite tip, enable studies of electrochemical and mechanical phenomena underlying dendrite growth in ceramic electrolytes. All experiments were conducted on the most electrochemically stable Li-ion conducting solid electrolyte (tantalum-doped lithium lanthanum zirconium oxide). References: Sudworth, J. L., Hames, M. D., Storey, M. A., Azim, M. F. & Tilley, A. R. An analysis and laboratory assessment of Two Sodium Sulfur Cell Designs. Power Sources 4, 1–18 (1972). Sharafi, A. S. et al. Characterizing the Li–Li7La3Zr2O12 interface stability and kinetics as a function of temperature and current density. J. Power Sources 302, 135–139 (2016). Fincher, C. D. et al. Controlling dendrite propagation in solid-state batteries with engineered stress. Joule 6, 2794-2809 (2022). Porz†, L., Swamy†, T. et al. Mechanism of lithium metal penetration through inorganic solid electrolytes. Adv. Energy Mater. 7, 1701003 (2017). Athanasiou†, C. E., Fincher†, C. D. et al. Operando measurements of dendrite-induced stresses in ceramic electrolytes using photoelasticity. Matter (2023). Fincher C. D., et al. In prep. Figure 1: Operando birefringence imaging enables direct measurement of dendrite-induced stresses in solid-electrolytes. Pixel-by-pixel computational analysis allows measurement of the mechanical driving force for crack growth, (the strain energy release rate).6 (a) Dendrites are grown through the plane of a thin LLZO solid electrolyte which was mechanically thinned to the point of translucency. A microscope is used to collect (b) polarized light images of dendrite propagation, and (c) spatially resolved measurements of the max shear stress in the solid electrolyte. The stress measurements in (c) correspond to the region enclosed by the dashed black box in (b). The strain energy release rate is determined by fitting the experimentally determined stress field (c) to that expected analytically (d), using as a fitting parameter. (e) The stress distribution measured along a line profile starting at the crack tip and ending at a point 45° (in red) and 90° (in blue) from the propagation direction. The solid and dashed lines series represent data from the experimental and computed analytic stress fields in c and d, respectively. The end points of the 45° and 90° profiles are shown as red and blue “X” symbols in c and d, respectively. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (67) , 4543
Void-Suppression at Low Stack Pressures Using a Microstructurally Engineered Anode
Solid-state batteries (SSBs) with a Li+ working ion promise a step change in specific energy and safety by using less-reactive solid-state electrolytes (SSEs) in contact with Li metal. However, commercialization of SSBs has been hindered by low specific power due to contact loss at solid-solid interfaces. Voids nucleate and grow at the solid-solid interface between Li metal and the SSE, increasing interfacial resistance. It is hypothesized that during charging ionic current intensification at this interface, which magnifies with increased contact loss, can increase the driving force to nucleate Li dendrites which grow until a short circuit causes cell failure.1 A common workaround for these anode/SSE contact loss issues is to use high uniaxial stack pressures (>1 MPa) applied normal to the planar interface; one theory is that mechanical deformation of Li metal via power-law creep suppresses void growth.2,3 This approach negates one of the proposed benefits of SSBs: high stack pressures require additional mechanical fixturing components which reduces the cell specific energy. We introduce a microstructured Li metal anode which, while operating in contact with Li6.75La3Zr1.75Ta0.25O12 (LLZTO) SSE at low stack pressures (0.15 MPa) and at room temperature, achieves stable Li stripping for areal capacities more than 10 times that of a lithium control group at current densities up to 1 mA cm-2. We will discuss the mechanisms enabling this suppression of contact loss using data from 3-electrode (Li reference) galvanostatic tests allowing contributions from the stripping and plating electrodes to be deconvoluted. References: [1] Raj, V.; Venturi, V.; Kankanallu, V. R.; Kuiri, B.; Viswanathan, V.; Aetukuri, N. P. B. Direct Correlation between Void Formation and Lithium Dendrite Growth in Solid-State Electrolytes with Interlayers. Nat. Mater. 2022, 21 (9), 1050–1056. [2] Wang, M. J.; Choudhury, R.; Sakamoto, J. Characterizing the Li-Solid-Electrolyte Interface Dynamics as a Function of Stack Pressure and Current Density. Joule 2019, 3 (9), 2165–2178. [3] Fincher, C. D.; Ojeda, D.; Zhang, Y.; Pharr, G. M.; Pharr, M. Mechanical Properties of Metallic Lithium: From Nano to Bulk Scales. Acta Mater. 2020, 186, 215–222. Acknowledgements: Funding is gratefully acknowledged from Morphogenic Interfaces, Defense Advanced Research Project Agency, contract HR00112220032. V.D.V. acknowledges funding from the National Science Foundation Graduate Research Fellowship Program. C.Y.L. acknowledges funding from the Chiang-Chen Overseas Fellowship. C.D.F acknowledges funding from the Department of Defense National Defense Science and Engineering Graduate Fellowship.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (67) , 4543
Void-Suppression at Low Stack Pressures Using a Microstructurally Engineered Anode
Solid-state batteries (SSBs) with a Li+ working ion promise a step change in specific energy and safety by using less-reactive solid-state electrolytes (SSEs) in contact with Li metal. However, commercialization of SSBs has been hindered by low specific power due to contact loss at solid-solid interfaces. Voids nucleate and grow at the solid-solid interface between Li metal and the SSE, increasing interfacial resistance. It is hypothesized that during charging ionic current intensification at this interface, which magnifies with increased contact loss, can increase the driving force to nucleate Li dendrites which grow until a short circuit causes cell failure.1 A common workaround for these anode/SSE contact loss issues is to use high uniaxial stack pressures (>1 MPa) applied normal to the planar interface; one theory is that mechanical deformation of Li metal via power-law creep suppresses void growth.2,3 This approach negates one of the proposed benefits of SSBs: high stack pressures require additional mechanical fixturing components which reduces the cell specific energy. We introduce a microstructured Li metal anode which, while operating in contact with Li6.75La3Zr1.75Ta0.25O12 (LLZTO) SSE at low stack pressures (0.15 MPa) and at room temperature, achieves stable Li stripping for areal capacities more than 10 times that of a lithium control group at current densities up to 1 mA cm-2. We will discuss the mechanisms enabling this suppression of contact loss using data from 3-electrode (Li reference) galvanostatic tests allowing contributions from the stripping and plating electrodes to be deconvoluted. References: [1] Raj, V.; Venturi, V.; Kankanallu, V. R.; Kuiri, B.; Viswanathan, V.; Aetukuri, N. P. B. Direct Correlation between Void Formation and Lithium Dendrite Growth in Solid-State Electrolytes with Interlayers. Nat. Mater. 2022, 21 (9), 1050–1056. [2] Wang, M. J.; Choudhury, R.; Sakamoto, J. Characterizing the Li-Solid-Electrolyte Interface Dynamics as a Function of Stack Pressure and Current Density. Joule 2019, 3 (9), 2165–2178. [3] Fincher, C. D.; Ojeda, D.; Zhang, Y.; Pharr, G. M.; Pharr, M. Mechanical Properties of Metallic Lithium: From Nano to Bulk Scales. Acta Mater. 2020, 186, 215–222. Acknowledgements: Funding is gratefully acknowledged from Morphogenic Interfaces, Defense Advanced Research Project Agency, contract HR00112220032. V.D.V. acknowledges funding from the National Science Foundation Graduate Research Fellowship Program. C.Y.L. acknowledges funding from the Chiang-Chen Overseas Fellowship. C.D.F acknowledges funding from the Department of Defense National Defense Science and Engineering Graduate Fellowship.
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (38) , 2300
Electrochemical Embrittlement Accelerates Dendrite Growth in Ceramic Electrolytes
Although solid-state batteries with metal anodes promise to enable safer, higher energy density batteries, metal protrusions (dendrites) grow when charging faster than a critical current density[1,2]. It is generally believed that dendrites grow when plating-induced stresses exceed that required for fracture of the solid-electrolyte[2–4]. Although the electrolyte's fracture toughness is commonly taken as a constant[2–4], here we show that the effective fracture toughness depends markedly upon the metal deposition current density. Based upon operando birefringence microscopy[5], we directly measure dendrite-induced stresses and obtain the mechanical driving force for failure, as well as the electrolyte fracture toughness. We find that increasing current densities embrittle the solid electrolyte—diminishing the fracture toughness by as much as 70%. Cryogenic Scanning Transmission Electron Microscopy (Cryo-STEM) reveals decomposed electrolyte phases at the dendrite tip. This decomposition is associated with a volume contraction consistent with embrittlement of the electrolyte. All experiments were conducted on the most electrochemically stable Li-ion conducting solid electrolyte (tantalum-doped lithium lanthanum zirconium oxide); the fracture toughness of less stable electrolytes (e.g., agryodites) may be even more susceptible to such embrittlement. The collective results indicate that “electrochemical embrittlement” markedly weakens the electrolyte, enabling dendrite growth—even when such degradation has negligible effect on bulk electrochemical properties. References: Sudworth, J. L., Hames, M. D., Storey, M. A., Azim, M. F. & Tilley, A. R. An analysis and laboratory assessment of Two Sodium Sulfur Cell Designs. Power Sources 4, 1–18 (1972). Sharafi, A., Meyer, H. M., Nanda, J., Wolfenstine, J. & Sakamoto, J. Characterizing the Li–Li7La3Zr2O12 interface stability and kinetics as a function of temperature and current density. J. Power Sources 302, 135–139 (2016). Fincher, C. D. et al. Controlling dendrite propagation in solid-state batteries with engineered stress. Joule 6, 2794-2809 (2022). Porz, L. et al. Mechanism of lithium metal penetration through inorganic solid electrolytes. Adv. Energy Mater. 7, 1701003 (2017). Athanasiou†, C. E., Fincher†, C. D. et al. Operando measurements of dendrite-induced stresses in ceramic electrolytes using photoelasticity. Matter (2023).
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (38) , 2300
Electrochemical Embrittlement Accelerates Dendrite Growth in Ceramic Electrolytes
Although solid-state batteries with metal anodes promise to enable safer, higher energy density batteries, metal protrusions (dendrites) grow when charging faster than a critical current density[1,2]. It is generally believed that dendrites grow when plating-induced stresses exceed that required for fracture of the solid-electrolyte[2–4]. Although the electrolyte's fracture toughness is commonly taken as a constant[2–4], here we show that the effective fracture toughness depends markedly upon the metal deposition current density. Based upon operando birefringence microscopy[5], we directly measure dendrite-induced stresses and obtain the mechanical driving force for failure, as well as the electrolyte fracture toughness. We find that increasing current densities embrittle the solid electrolyte—diminishing the fracture toughness by as much as 70%. Cryogenic Scanning Transmission Electron Microscopy (Cryo-STEM) reveals decomposed electrolyte phases at the dendrite tip. This decomposition is associated with a volume contraction consistent with embrittlement of the electrolyte. All experiments were conducted on the most electrochemically stable Li-ion conducting solid electrolyte (tantalum-doped lithium lanthanum zirconium oxide); the fracture toughness of less stable electrolytes (e.g., agryodites) may be even more susceptible to such embrittlement. The collective results indicate that “electrochemical embrittlement” markedly weakens the electrolyte, enabling dendrite growth—even when such degradation has negligible effect on bulk electrochemical properties. References: Sudworth, J. L., Hames, M. D., Storey, M. A., Azim, M. F. & Tilley, A. R. An analysis and laboratory assessment of Two Sodium Sulfur Cell Designs. Power Sources 4, 1–18 (1972). Sharafi, A., Meyer, H. M., Nanda, J., Wolfenstine, J. & Sakamoto, J. Characterizing the Li–Li7La3Zr2O12 interface stability and kinetics as a function of temperature and current density. J. Power Sources 302, 135–139 (2016). Fincher, C. D. et al. Controlling dendrite propagation in solid-state batteries with engineered stress. Joule 6, 2794-2809 (2022). Porz, L. et al. Mechanism of lithium metal penetration through inorganic solid electrolytes. Adv. Energy Mater. 7, 1701003 (2017). Athanasiou†, C. E., Fincher†, C. D. et al. Operando measurements of dendrite-induced stresses in ceramic electrolytes using photoelasticity. Matter (2023).
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (55) , 2936
Solid-State Lithium-Ion Conductor via Reversible Self-Assembly of Aramid Amphiphiles
Lithium-ion batteries are critical in advancing carbon neutrality and sustainable development. However, their end-of-life management and the recyclability remain significant challenges. We investigated an alternative approach to improve the recyclability of lithium-ion batteries by incorporating a layer of reversible materials, acting as an 'upon-disposal switch.' This switch facilitates the smooth delamination of battery components upon recycle process, enabling a more efficient and clean separation of battery components to facilitate direct recycling. Inspired by the principles of biodegradability, we explore the use of organic small molecule self-assembled nanoribbons as the reversible layer integrated in the battery cell. These supramolecular nanoribbons are tailored to overcome the typical stability issues of self-assembled nanostructure and conduct lithium-ion as a solid-state electrolyte. This study delves into the performance and transport mechanisms of these supramolecular nanomaterials and presents a proof-of-concept demonstration of direct recyclability. Figure 1
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (55) , 2936
Solid-State Lithium-Ion Conductor via Reversible Self-Assembly of Aramid Amphiphiles
Lithium-ion batteries are critical in advancing carbon neutrality and sustainable development. However, their end-of-life management and the recyclability remain significant challenges. We investigated an alternative approach to improve the recyclability of lithium-ion batteries by incorporating a layer of reversible materials, acting as an 'upon-disposal switch.' This switch facilitates the smooth delamination of battery components upon recycle process, enabling a more efficient and clean separation of battery components to facilitate direct recycling. Inspired by the principles of biodegradability, we explore the use of organic small molecule self-assembled nanoribbons as the reversible layer integrated in the battery cell. These supramolecular nanoribbons are tailored to overcome the typical stability issues of self-assembled nanostructure and conduct lithium-ion as a solid-state electrolyte. This study delves into the performance and transport mechanisms of these supramolecular nanomaterials and presents a proof-of-concept demonstration of direct recyclability. Figure 1
- 13 April 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (23) , 2304530
Mechanical Milling – Induced Microstructure Changes in Argyrodite LPSCl Solid‐State Electrolyte Critically Affect Electrochemical Stability
Microstructure of argyrodite solid‐state electrolyte (SSE) critically affects lithium metal electrodeposition/dissolution. While the stability of unmodified SSE is mediocre, once optimized state‐of‐the‐art electrochemical performance is achieved (symmetric cells, full cells with NMC811) without secondary interlayers or functionalized current collectors. Planetary mechanical milling in wet media (m‐xylene) is employed to alter commercial Li6PS5Cl (LPSCl) powder. Quantitative stereology demonstrates how milling progressively refines grain and pore size/distribution in the SSE compact, increases its density, and geometrically smoothens the SSE‐Li interface. Mechanical indentation demonstrates that these changes lead to reduced site‐to‐site variation in the compact's hardness. Milled microstructures promote uniform early‐stage electrodeposition on foil collectors and stabilize solid electrolyte interphase (SEI) reactivity. Analysis of half‐cells with bilayer electrolytes demonstrates the importance of microstructure directly contacting current collector, with interface roughness due to pore and grain size distribution being key. For the first time, short‐circuiting Li metal dendrite is directly identified, employing 1.5 mm diameter “mini” symmetrical cell and cryogenic focused ion beam (cryo‐FIB) electron microscopy. The branching sheet‐like dendrite traverses intergranularly, filling the interparticle voids and forming an SEI around it. Mesoscale modeling reveals the relationship between Li‐SSE interface morphology and the onset of electrochemical instability, based on underlying reaction current distribution.
- 13 April 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (23) , 2304530
Mechanical Milling – Induced Microstructure Changes in Argyrodite LPSCl Solid‐State Electrolyte Critically Affect Electrochemical Stability
Microstructure of argyrodite solid‐state electrolyte (SSE) critically affects lithium metal electrodeposition/dissolution. While the stability of unmodified SSE is mediocre, once optimized state‐of‐the‐art electrochemical performance is achieved (symmetric cells, full cells with NMC811) without secondary interlayers or functionalized current collectors. Planetary mechanical milling in wet media (m‐xylene) is employed to alter commercial Li6PS5Cl (LPSCl) powder. Quantitative stereology demonstrates how milling progressively refines grain and pore size/distribution in the SSE compact, increases its density, and geometrically smoothens the SSE‐Li interface. Mechanical indentation demonstrates that these changes lead to reduced site‐to‐site variation in the compact's hardness. Milled microstructures promote uniform early‐stage electrodeposition on foil collectors and stabilize solid electrolyte interphase (SEI) reactivity. Analysis of half‐cells with bilayer electrolytes demonstrates the importance of microstructure directly contacting current collector, with interface roughness due to pore and grain size distribution being key. For the first time, short‐circuiting Li metal dendrite is directly identified, employing 1.5 mm diameter “mini” symmetrical cell and cryogenic focused ion beam (cryo‐FIB) electron microscopy. The branching sheet‐like dendrite traverses intergranularly, filling the interparticle voids and forming an SEI around it. Mesoscale modeling reveals the relationship between Li‐SSE interface morphology and the onset of electrochemical instability, based on underlying reaction current distribution.
- Open Access
- 28 December 2023
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (9)
Harnessing Electrochemical‐Mechanical Couplings to Improve the Reliability of Solid‐State Batteries
One key barrier to using lithium‐metal anode batteries is that metal dendrites can penetrate solid electrolytes, causing short‐circuits and battery failures. It is established that this failure is likely caused by crack propagation due to electrodeposition‐induced stresses from lithium metal. This study explores ways to harness these electrochemical‐mechanical couplings to control dendrite growth and improve battery reliability using a phase‐field model and targeted fracture experiments. The results show that dendrite growth can be effectively mitigated by applying mechanical stresses or tailoring the material's fracture toughness. This study also outlines the requirements for compressive stress to halt or deflect dendrites as a function of the overpotential and discusses the role of microstructure in this process.
- 28 December 2023
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (9)
Open AccessHarnessing Electrochemical‐Mechanical Couplings to Improve the Reliability of Solid‐State Batteries
One key barrier to using lithium‐metal anode batteries is that metal dendrites can penetrate solid electrolytes, causing short‐circuits and battery failures. It is established that this failure is likely caused by crack propagation due to electrodeposition‐induced stresses from lithium metal. This study explores ways to harness these electrochemical‐mechanical couplings to control dendrite growth and improve battery reliability using a phase‐field model and targeted fracture experiments. The results show that dendrite growth can be effectively mitigated by applying mechanical stresses or tailoring the material's fracture toughness. This study also outlines the requirements for compressive stress to halt or deflect dendrites as a function of the overpotential and discusses the role of microstructure in this process.