Andrea Parise
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrea Parise has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Luigi Pugliese
Department of Civil Engineering, University of Calabria, Rende, Italy
7 shared publications - Antonello Troncone
Department of Civil Engineering, University of Calabria, Rende, Italy
6 shared publications - Enrico Conte
Department of Civil Engineering, University of Calabria, Rende, Italy
6 shared publications - Angelo Furfaro
University of Calabria
1 shared publication Antonello Troncone
1 shared publication- Antonio Piccolo
Department of Engineering, University of Messina, Contrada di Dio, 98166 Messina, Italy
1 shared publication
Latest Publications
- 2 September 2026
- Published by Springer Nature
- p. 38-45
A Practical Method for the Predictive Analysis of Landslides in Sensitive Clays
- 2 September 2026
- Published by Springer Nature
- p. 38-45
A Practical Method for the Predictive Analysis of Landslides in Sensitive Clays
- 13 March 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 179 (2) , 219-232
Settlement analysis of residential buildings with eccentric loads and complex subsoil conditions
In the present paper, an analysis is performed on the movements undergone by some residential buildings in 1983, during their construction. A common feature of these buildings is an asymmetric superstructure that makes the vertical loads acting on the foundations highly eccentric. A sloping ground surface and a complex subsoil condition, characterised by the presence of strongly inclined layers of compressible soils, were other predisposing factors for the observed movements. The buildings underwent a significant rigid rotation (tilt) to the extent that their serviceability was compromised because of the resulting floor inclination. As a consequence, construction was suspended and a subsurface investigation consisting of boreholes, cone penetration tests and conventional laboratory tests was performed. In addition, the vertical displacement of some representative points of the building foundations was measured during a period of about 1 year. A finite-element analysis of the building displacements is carried out in the present study to highlight the different roles played by load eccentricity, soil layering and a sloping ground surface in causing the observed building movements. To restore the serviceability of the buildings, their foundations were underpinned with micropiles, some of which were pre-stressed. The effectiveness of this measure is also analysed.
- 13 March 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 179 (2) , 219-232
Settlement analysis of residential buildings with eccentric loads and complex subsoil conditions
In the present paper, an analysis is performed on the movements undergone by some residential buildings in 1983, during their construction. A common feature of these buildings is an asymmetric superstructure that makes the vertical loads acting on the foundations highly eccentric. A sloping ground surface and a complex subsoil condition, characterised by the presence of strongly inclined layers of compressible soils, were other predisposing factors for the observed movements. The buildings underwent a significant rigid rotation (tilt) to the extent that their serviceability was compromised because of the resulting floor inclination. As a consequence, construction was suspended and a subsurface investigation consisting of boreholes, cone penetration tests and conventional laboratory tests was performed. In addition, the vertical displacement of some representative points of the building foundations was measured during a period of about 1 year. A finite-element analysis of the building displacements is carried out in the present study to highlight the different roles played by load eccentricity, soil layering and a sloping ground surface in causing the observed building movements. To restore the serviceability of the buildings, their foundations were underpinned with micropiles, some of which were pre-stressed. The effectiveness of this measure is also analysed.
- Open Access
- 1 July 2025
- Published by Elsevier in Soils and Foundations
- Vol. 65 (4)
An approach for predicting earthquake-induced permanent displacements of embedded cantilever walls in soils with cohesion
- 1 July 2025
- Published by Elsevier in Soils and Foundations
- Vol. 65 (4)
Open AccessAn approach for predicting earthquake-induced permanent displacements of embedded cantilever walls in soils with cohesion
- 17 June 2023
- Published by Springer Nature
- p. 553-560
A Simplified Method for Relating Rainfall to Movements of Slopes Reinforced by Piles
- 17 June 2023
- Published by Springer Nature
- p. 553-560
A Simplified Method for Relating Rainfall to Movements of Slopes Reinforced by Piles
- 17 June 2023
- Published by Springer Nature
- p. 561-568
Back-Analysis of the Post-failure Stage of a Landslide in Sensitive Clays
- 17 June 2023
- Published by Springer Nature
- p. 561-568
Back-Analysis of the Post-failure Stage of a Landslide in Sensitive Clays
- Open Access
- 1 June 2023
- Published by Emerald Publishing in Geotechnical Research
- Vol. 10 (2) , 67-77
Analysis of a landslide in sensitive clays using the material point method
Slope movements are generally classified into four different phases: pre-failure, failure, post-failure and eventual reactivation. In engineering applications, the pre-failure and failure phases are usually analysed using traditional numerical techniques, such as the finite-element method and the finite-difference method. However, these methods are often based on the assumption of small deformations and consequently are unsuitable for analysing the slope behaviour during the post-failure stage, which is usually characterised by very large deformations. To overcome this shortcoming, the material point method (MPM) is employed in the present study. Specifically, MPM is used to perform an analysis of a landslide in sensitive clays that occurred at Saint-Jude (Quebec, Canada) in 2010. To assess the accuracy of the analysis, the final profile and the displacement magnitude detected after the event are compared with those obtained by the numerical simulation. The results provided by MPM are in satisfactory agreement with field observations. The failure mechanism and the development of the failure surface within the slope are also reproduced successfully. These results also show that MPM is an attractive method for analysing the kinematics of landslides in sensitive clays, requiring also a limited number of conventional geotechnical parameters as input data.
- 1 June 2023
- Published by Emerald Publishing in Geotechnical Research
- Vol. 10 (2) , 67-77
Open AccessAnalysis of a landslide in sensitive clays using the material point method
Slope movements are generally classified into four different phases: pre-failure, failure, post-failure and eventual reactivation. In engineering applications, the pre-failure and failure phases are usually analysed using traditional numerical techniques, such as the finite-element method and the finite-difference method. However, these methods are often based on the assumption of small deformations and consequently are unsuitable for analysing the slope behaviour during the post-failure stage, which is usually characterised by very large deformations. To overcome this shortcoming, the material point method (MPM) is employed in the present study. Specifically, MPM is used to perform an analysis of a landslide in sensitive clays that occurred at Saint-Jude (Quebec, Canada) in 2010. To assess the accuracy of the analysis, the final profile and the displacement magnitude detected after the event are compared with those obtained by the numerical simulation. The results provided by MPM are in satisfactory agreement with field observations. The failure mechanism and the development of the failure surface within the slope are also reproduced successfully. These results also show that MPM is an attractive method for analysing the kinematics of landslides in sensitive clays, requiring also a limited number of conventional geotechnical parameters as input data.
- 1 September 2022
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 12 (3) , 167-173
A simple method to reduce mesh dependency in modelling landslides involving brittle soils
This paper focuses on the numerical simulation of the deformation processes occurring in the slopes when soils with strain-softening behaviour are involved. In these circumstances, a progressive failure may occur with the consequent motion of the unstable soil mass in the post-failure stage. This problem can be only solved using advanced numerical techniques capable also of accounting for the occurrence of large deformations. However, the solution is generally mesh dependent and may be affected by lack of convergence. In this study, the material point method is employed to simulate the occurrence of large deformations, in conjunction with a strain-softening Mohr–Coulomb constitutive model, in which the shear strength parameters are reduced as a function of the accumulated deviatoric plastic strain, and a model parameter controlling the rate of strength decrease. To evaluate this parameter and to reduce the effects of the mesh dependency on the numerical solution, a novel procedure based on the results of direct shear tests is presented. This methodology is completely analytical and requires few parameters with a clear physical meaning and of simple experimental determination. Some simulations are performed to assess the reliability of the proposed procedure.
- 1 September 2022
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 12 (3) , 167-173
A simple method to reduce mesh dependency in modelling landslides involving brittle soils
This paper focuses on the numerical simulation of the deformation processes occurring in the slopes when soils with strain-softening behaviour are involved. In these circumstances, a progressive failure may occur with the consequent motion of the unstable soil mass in the post-failure stage. This problem can be only solved using advanced numerical techniques capable also of accounting for the occurrence of large deformations. However, the solution is generally mesh dependent and may be affected by lack of convergence. In this study, the material point method is employed to simulate the occurrence of large deformations, in conjunction with a strain-softening Mohr–Coulomb constitutive model, in which the shear strength parameters are reduced as a function of the accumulated deviatoric plastic strain, and a model parameter controlling the rate of strength decrease. To evaluate this parameter and to reduce the effects of the mesh dependency on the numerical solution, a novel procedure based on the results of direct shear tests is presented. This methodology is completely analytical and requires few parameters with a clear physical meaning and of simple experimental determination. Some simulations are performed to assess the reliability of the proposed procedure.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 351-358
A virtual environment for the enactment of realistic cyber security scenarios
In the last few years, cyber security has become a hot topic because of the ever-increasing availability of Internet accessible services driven by the diffusion of connected devices. The consequent exposition to cyber threats demands for suitable methodologies, techniques and tools allowing to adequately handle issues arising in such a complex domain. We argue that the flexibility of virtual environments will play a critical role in many cyber security related aspects. Problems like the assessment of newly devised intrusion detection techniques, the evaluation of skills of cyber defense team members, the evaluation of the disruptive effects caused by the diffusion of new malware, are just few examples of issues that cannot be directly addressed in production systems even though they require realistic operating environments in order to be suitably performed. This paper describes the architecture of SMALLWORLD, a scalable software platform designed to reproduce realistic scenarios achieved by the immersion of real systems into a software defined virtual environment.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 351-358
A virtual environment for the enactment of realistic cyber security scenarios
In the last few years, cyber security has become a hot topic because of the ever-increasing availability of Internet accessible services driven by the diffusion of connected devices. The consequent exposition to cyber threats demands for suitable methodologies, techniques and tools allowing to adequately handle issues arising in such a complex domain. We argue that the flexibility of virtual environments will play a critical role in many cyber security related aspects. Problems like the assessment of newly devised intrusion detection techniques, the evaluation of skills of cyber defense team members, the evaluation of the disruptive effects caused by the diffusion of new malware, are just few examples of issues that cannot be directly addressed in production systems even though they require realistic operating environments in order to be suitably performed. This paper describes the architecture of SMALLWORLD, a scalable software platform designed to reproduce realistic scenarios achieved by the immersion of real systems into a software defined virtual environment.