Frank Schäfer
Research Subjects
Frank Schäfer has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Michael Holzapfel
Fraunhofer Institute for Chemical Technology ICT
2 shared publications- Achim Hartschuh
Department of Chemistry and Center for NanoScience (CeNS), University of Munich (LMU), Butenandtstraße 5-13, Munich 81377, Germany
1 shared publication - Felix Gerbig
Karlsruhe Institute of Technology
1 shared publication Hermann Nirschl
Karlsruhe Institute of Technology
1 shared publicationJens Tübke
Fraunhofer-Institute for Chemical Technology ICT
1 shared publicationNadja Giesbrecht
Department of Chemistry and Center for NanoScience (CeNS) , LMU Munich , Butenandtstr. 5-13 , 81377 Munich , Germany
1 shared publication
Latest Publications
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (3) , 617
Optimizing Mid-Temperature Sodium Iodine Batteries for Sustainable Large-Scale Energy Storage: A Comprehensive Modeling Approach and Experimental Validation
The need for safe, eco-friendly, low-cost batteries for large scale implementation rises in the presence of the expansions of renewable energy sources. High-temperature liquid sodium batteries (e.g. sodium-sulfur) are a well-established technology for large-scale grid storage. Combining the molten sodium anode with an aqueous iodine cathode overcomes the problems of thermal loses and sealing by reducing the operating temperature to about 100°C. This leads to higher cost efficiency, energy density and a simplified cell design. Here we present a novel modelling approach for complex carbon-based cathode structures and its limits and abilities on enhancing the utilizable capacity. Due to their sustainability and high efficiency, which is comparable to Li-Ion –batteries, mid-temperature sodium-iodine batteries are a promising candidate for stationary energy storage applications. With a high specific energy of around 200 Wh kg-1, sodium-iodine batteries have the ability to meet the growing demand of short-term energy storage caused by the integration of renewable energy sources into the power grid. Up to this day, the detailed processes inside the battery are not well-understood. Quantities like initial species concentrations, C-rate, cell design and cathode geometry have large impacts on the overall battery performance. A deeper understanding of these processes is inevitable for enhancing the battery performance by choosing the optimal abovementioned quantities. We set up a fully resolved 3D Simulation model to gain insight into microstructural processes inside the battery, as experimental studies are limited to macroscopic quantities like electronic current and potential. The methodology is based on continuum hypothesis by using an open-source CFD software, which is rewritten accordingly. The proposed spatially resolved three-dimensional simulation model takes charge and mass transport, heterogeneous and homogeneous reactions as well as the electrochemical processes into account. Results show that transport limitations confine the utilizable capacity of the battery [1]. This contribution focuses on enhancing the battery energy density and efficiency by including open-pored glassy carbon foam structures in the cathode half-cell [2, 3]. We state simulation predicted, optimal morphology properties of such a structure. Furthermore, we describe the evaluation of improved thermodynamic data of the aqueous iodine solution by refitting simulation results to polarization curves. We utilize a novel impedance spectroscopy simulation method for sodium iodine batteries to improve parameterization of the underlying electrochemical model by comparing the results with experimental data. References Gerbig, F., Cernak, S., Nirschl, H. (2021). 3D Simulation of Cell Design Influences on Sodium–Iodine Battery Performance. Energy Technology, vol. 9, no. 6, p. 2000857 Gerbig, F., Cernak, S. and Nirschl H. (2021), Towards a Novel Sodium-Iodine Battery with an Aqueous Catholyte: Numerical Investigations of Complex Cathode Structures, ECS Trans., vol. 104, no. 1, pp. 123–130 Gerbig, M. Holzapfel, and H. Nirschl, Simulating the Impact of Glassy Carbon Foam Electrodes on the Performance of Sodium Iodine Batteries, J. Electrochem. Soc., vol. 170, no. 4, p. 40517, 2023, doi: 10.1149/1945-7111/accab7. Figure 1
- 9 August 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-01 (3) , 617
Optimizing Mid-Temperature Sodium Iodine Batteries for Sustainable Large-Scale Energy Storage: A Comprehensive Modeling Approach and Experimental Validation
The need for safe, eco-friendly, low-cost batteries for large scale implementation rises in the presence of the expansions of renewable energy sources. High-temperature liquid sodium batteries (e.g. sodium-sulfur) are a well-established technology for large-scale grid storage. Combining the molten sodium anode with an aqueous iodine cathode overcomes the problems of thermal loses and sealing by reducing the operating temperature to about 100°C. This leads to higher cost efficiency, energy density and a simplified cell design. Here we present a novel modelling approach for complex carbon-based cathode structures and its limits and abilities on enhancing the utilizable capacity. Due to their sustainability and high efficiency, which is comparable to Li-Ion –batteries, mid-temperature sodium-iodine batteries are a promising candidate for stationary energy storage applications. With a high specific energy of around 200 Wh kg-1, sodium-iodine batteries have the ability to meet the growing demand of short-term energy storage caused by the integration of renewable energy sources into the power grid. Up to this day, the detailed processes inside the battery are not well-understood. Quantities like initial species concentrations, C-rate, cell design and cathode geometry have large impacts on the overall battery performance. A deeper understanding of these processes is inevitable for enhancing the battery performance by choosing the optimal abovementioned quantities. We set up a fully resolved 3D Simulation model to gain insight into microstructural processes inside the battery, as experimental studies are limited to macroscopic quantities like electronic current and potential. The methodology is based on continuum hypothesis by using an open-source CFD software, which is rewritten accordingly. The proposed spatially resolved three-dimensional simulation model takes charge and mass transport, heterogeneous and homogeneous reactions as well as the electrochemical processes into account. Results show that transport limitations confine the utilizable capacity of the battery [1]. This contribution focuses on enhancing the battery energy density and efficiency by including open-pored glassy carbon foam structures in the cathode half-cell [2, 3]. We state simulation predicted, optimal morphology properties of such a structure. Furthermore, we describe the evaluation of improved thermodynamic data of the aqueous iodine solution by refitting simulation results to polarization curves. We utilize a novel impedance spectroscopy simulation method for sodium iodine batteries to improve parameterization of the underlying electrochemical model by comparing the results with experimental data. References Gerbig, F., Cernak, S., Nirschl, H. (2021). 3D Simulation of Cell Design Influences on Sodium–Iodine Battery Performance. Energy Technology, vol. 9, no. 6, p. 2000857 Gerbig, F., Cernak, S. and Nirschl H. (2021), Towards a Novel Sodium-Iodine Battery with an Aqueous Catholyte: Numerical Investigations of Complex Cathode Structures, ECS Trans., vol. 104, no. 1, pp. 123–130 Gerbig, M. Holzapfel, and H. Nirschl, Simulating the Impact of Glassy Carbon Foam Electrodes on the Performance of Sodium Iodine Batteries, J. Electrochem. Soc., vol. 170, no. 4, p. 40517, 2023, doi: 10.1149/1945-7111/accab7. Figure 1
- 7 July 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-01 (1) , 102
Medium-Temperature Sodium-Iodine Battery System
A medium-temperature sodium-iodine battery system is presented. The rechargeable molten-sodium system works at approx. 100 °C with high efficiency, and potentially lower cost than existing high-temperature sodium-batteries (which are usually operating at a temperature of around 300 °C). Our battery system uses an aqueous iodine/iodide solution as catholyte and sodium-ion conductive Zr-based NaSICON ceramic material as solid electrolyte. The free halogen, which is formed upon charge, is complexed as highly soluble triiodide. Long-term stability of sodium-ion conductive material in contact with aqueous electrolytes, generally, is a concern. NaSICON-based ceramic material has shown not only an enhanced stability [1] against these electrolytes but also an increased sodium-ion conductivity [2], compared to sodium β″-alumina used in sodium-sulfur batteries. The sodium-iodine system has shown to operate in a stable manner with a catholyte allowing for a high total iodine concentration (>3.0 mol/L) [1]. Substitution in the NaSICON composition allows for increased ionic conductivity and enhanced stability against the aqueous cathode. In the case of fissuring of the NaSICON ceramic separator, only solid products are formed. This stops the direct reaction of active materials. [1] M. Holzapfel, D. Wilde, C. Hupbauer, K. Ahlbrecht, T. Berger, Electrochim. Acta 237 (2017), 12-21. [2] S. Naqash, Q. Ma, F. Tietz, O. Guillon, Solid State Ionics 302 (2017), 83-91. This work is funded by the German Federal Ministry of Education and Research in the project „MiTemp – Mitteltemperatur-Natriumbatterien mit flüssiger Natriumanode und wässriger Iodkathode“ (03XP0183A). Figure 1
- 7 July 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-01 (1) , 102
Medium-Temperature Sodium-Iodine Battery System
A medium-temperature sodium-iodine battery system is presented. The rechargeable molten-sodium system works at approx. 100 °C with high efficiency, and potentially lower cost than existing high-temperature sodium-batteries (which are usually operating at a temperature of around 300 °C). Our battery system uses an aqueous iodine/iodide solution as catholyte and sodium-ion conductive Zr-based NaSICON ceramic material as solid electrolyte. The free halogen, which is formed upon charge, is complexed as highly soluble triiodide. Long-term stability of sodium-ion conductive material in contact with aqueous electrolytes, generally, is a concern. NaSICON-based ceramic material has shown not only an enhanced stability [1] against these electrolytes but also an increased sodium-ion conductivity [2], compared to sodium β″-alumina used in sodium-sulfur batteries. The sodium-iodine system has shown to operate in a stable manner with a catholyte allowing for a high total iodine concentration (>3.0 mol/L) [1]. Substitution in the NaSICON composition allows for increased ionic conductivity and enhanced stability against the aqueous cathode. In the case of fissuring of the NaSICON ceramic separator, only solid products are formed. This stops the direct reaction of active materials. [1] M. Holzapfel, D. Wilde, C. Hupbauer, K. Ahlbrecht, T. Berger, Electrochim. Acta 237 (2017), 12-21. [2] S. Naqash, Q. Ma, F. Tietz, O. Guillon, Solid State Ionics 302 (2017), 83-91. This work is funded by the German Federal Ministry of Education and Research in the project „MiTemp – Mitteltemperatur-Natriumbatterien mit flüssiger Natriumanode und wässriger Iodkathode“ (03XP0183A). Figure 1
- Open Access
- 13 February 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (9) , 7974-7981
Grain Boundaries Act as Solid Walls for Charge Carrier Diffusion in Large Crystal MAPI Thin Films
Micro- and nanocrystalline methyl-ammonium lead-iodide (MAPI)-based thin film solar cells today reach power conversion effciencies of up to 20 %. We investigate the impact of grain boundaries on charge carrier transport in large crystal MAPI thin films using time-resolved photoluminescence (PL) microscopy and numerical model calculations. Crystals sizes in the range of several tens of micrometers allow for the spatially resolved study of boundary effects and their dynamics. While long-ranged diffusive charge carrier transport is observed within single crystals, no diffusive transport occurs across grain boundaries. The observed PL transients are found to crucially depend on the microscopic geometry of the crystal and the point of observation. In particular, spatially restricted diffusion of charge carriers leads to slower PL decay near crystal edges as compared to the crystal's center. In contrast to many reports in the literature our experimental results show no quenching or additional loss channels due to grain boundaries for the studied material, which thus do not negatively effect the performance of derived thin film devices.
- 13 February 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (9) , 7974-7981
Open AccessGrain Boundaries Act as Solid Walls for Charge Carrier Diffusion in Large Crystal MAPI Thin Films
Micro- and nanocrystalline methyl-ammonium lead-iodide (MAPI)-based thin film solar cells today reach power conversion effciencies of up to 20 %. We investigate the impact of grain boundaries on charge carrier transport in large crystal MAPI thin films using time-resolved photoluminescence (PL) microscopy and numerical model calculations. Crystals sizes in the range of several tens of micrometers allow for the spatially resolved study of boundary effects and their dynamics. While long-ranged diffusive charge carrier transport is observed within single crystals, no diffusive transport occurs across grain boundaries. The observed PL transients are found to crucially depend on the microscopic geometry of the crystal and the point of observation. In particular, spatially restricted diffusion of charge carriers leads to slower PL decay near crystal edges as compared to the crystal's center. In contrast to many reports in the literature our experimental results show no quenching or additional loss channels due to grain boundaries for the studied material, which thus do not negatively effect the performance of derived thin film devices.