Saba Shamim
Saba Shamim has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Rehan A. Khan
Department of Civil Engineering, Zakir Hussain College of Engineering and Technology, Aligarh Muslim University, Aligarh, India
3 shared publicationsShakeel Ahmad
Department of Civil Engineering, Zakir Hussain College of Engineering and Technology, Aligarh Muslim University, Aligarh, India
3 shared publicationsAmer M. Ibrahim
Department of Civil Engineering, College of Engineering, University of Diyala, Baqubah, Iraq
1 shared publication- Amer M. Ibrahim
Department of Civil Engineering, College of Engineering, University of Diyala, Baqubah 32001, Iraq
1 shared publication Hadee Mohammed Najm
New era and development in civil engineering research group, Scientific Research Center, Al-Ayen University, Nasiriyah, Iraq
1 shared publication- Hadee Mohammed Najm
Department of Civil Engineering, Zakir Husain Engineering College, Aligarh Muslim University, Aligarh 202002, India
1 shared publication
Latest Publications
- 31 August 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (4) , 4763-4784
Structural Performance of Reinforced Concrete One-Way Slabs Bubbled Using Hollow PET Balls
- 31 August 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (4) , 4763-4784
Structural Performance of Reinforced Concrete One-Way Slabs Bubbled Using Hollow PET Balls
- 7 July 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (8) , 1-13
Effect of waste ceramic sanitary ware as partial replacement of aggregates and cement in concrete
- 7 July 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (8) , 1-13
Effect of waste ceramic sanitary ware as partial replacement of aggregates and cement in concrete
- 31 January 2023
- Published by Elsevier in Engineering Failure Analysis
- Vol. 146
Numerical study on dynamic response of hollow and cavity type clay brick masonry infill panels subjected to blast loading
- 31 January 2023
- Published by Elsevier in Engineering Failure Analysis
- Vol. 146
Numerical study on dynamic response of hollow and cavity type clay brick masonry infill panels subjected to blast loading
- Open Access
Hybrid Effect of Steel Bars and PAN Textile Reinforcement on Ductility of One-Way Slab Subjected to Bending
Textile reinforced concrete (TRC) has gained attention from the construction industry due to several characteristics such as its lightweight, high tensile strength, design flexibility, corrosion resistance and remarkably long service life. Some structural applications that utilize TRC components include precast panels, structural repairs, waterproofing elements and façades. TRC is produced by incorporating textile fabrics into thin cementitious concrete panels. However, in order to use this strengthening method in construction practice, a design model is required. Investigating the combined effect of conventional steel and textile reinforcement on the ductility behavior of composite TRC/RC one-way slab is vitally important. Therefore, the current study describes the proper methods of calculating the ductility of the composite concrete reinforced by a direct combination of conventional steel and textile reinforcement. Four methods are presented to calculate the ductility of the three considered one-way slab specimens. The three slabs having dimensions 1500 mm × 500 mm × 50 mm were reinforced by steel bars (SRC), by steel with one layer of carbon fabric (SRC + 1T), and by steel with two layers of carbon fabric (SRC + 2T). The three slab specimens were cast by the hand lay-up method, removed from the molds, cured, and then tested in flexure after 28 days using the four-point bending method. The obtained results and calculations revealed the non-reasonability of using the conventional method based on yielding of steel reinforcement as the only criterion in the ductility determination. The results also confirmed the suitability of using the energy-based method over other discussed methods in the calculation of the ductility for the hybrid reinforced members.
Open AccessHybrid Effect of Steel Bars and PAN Textile Reinforcement on Ductility of One-Way Slab Subjected to Bending
Textile reinforced concrete (TRC) has gained attention from the construction industry due to several characteristics such as its lightweight, high tensile strength, design flexibility, corrosion resistance and remarkably long service life. Some structural applications that utilize TRC components include precast panels, structural repairs, waterproofing elements and façades. TRC is produced by incorporating textile fabrics into thin cementitious concrete panels. However, in order to use this strengthening method in construction practice, a design model is required. Investigating the combined effect of conventional steel and textile reinforcement on the ductility behavior of composite TRC/RC one-way slab is vitally important. Therefore, the current study describes the proper methods of calculating the ductility of the composite concrete reinforced by a direct combination of conventional steel and textile reinforcement. Four methods are presented to calculate the ductility of the three considered one-way slab specimens. The three slabs having dimensions 1500 mm × 500 mm × 50 mm were reinforced by steel bars (SRC), by steel with one layer of carbon fabric (SRC + 1T), and by steel with two layers of carbon fabric (SRC + 2T). The three slab specimens were cast by the hand lay-up method, removed from the molds, cured, and then tested in flexure after 28 days using the four-point bending method. The obtained results and calculations revealed the non-reasonability of using the conventional method based on yielding of steel reinforcement as the only criterion in the ductility determination. The results also confirmed the suitability of using the energy-based method over other discussed methods in the calculation of the ductility for the hybrid reinforced members.
- 15 July 2022
- Published by Springer Nature
- p. 78-89
Dynamic Response of Masonry Panel Under High-Strain Loading Condition
- 15 July 2022
- Published by Springer Nature
- p. 78-89
Dynamic Response of Masonry Panel Under High-Strain Loading Condition