Diane N. Collard
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diane N. Collard has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Steven F. Son
4 shared publications- Metin Örnek
School of Mechanical Engineering, Purdue University , West Lafayette, Indiana 47907
3 shared publications - Kyle E. Uhlenhake
Purdue University 2 , 500 Allison Road, West Lafayette, Indiana 47907, USA
2 shared publications Mahmuda Ishrat Malek
Department of Mechanical Engineering, Texas Tech University, Lubbock, Texas 79409, United States
2 shared publications- Michelle L. Pantoya
Department of Mechanical Engineering, Texas Tech University, Lubbock, USA
2 shared publications - Steven Son
School of Mechanical Engineering, Purdue University 1 , West Lafayette, Indiana 47907
2 shared publications
Latest Publications
- 27 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (10) , 2425-2432
Extending Aluminum Hydration Surface Treatments from Nanoparticles to Microparticles
- 27 September 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (10) , 2425-2432
Extending Aluminum Hydration Surface Treatments from Nanoparticles to Microparticles
- 29 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (6) , 1603-1611
Synthesis of Bayerite-Passivated Aluminum Particles and Their Combustion in Solid Propellants
- 29 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (6) , 1603-1611
Synthesis of Bayerite-Passivated Aluminum Particles and Their Combustion in Solid Propellants
- Open Access
- 17 November 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (19)
The effect of porosity on flexoelectricity in 3D printed aluminum/polyvinylidene fluoride composites
We investigated the relationship between porosity and flexoelectricity for aluminum (Al)/polyvinylidene fluoride (PVDF) composites. Neat PVDF, composites of micron aluminum (μAl)/PVDF, and composites of nano aluminum (nAl)/PVDF were 3D printed, and the flexoelectric response was measured using a cantilever beam test setup. Voids (up to 72.4 mm3) were incorporated into the samples by decreasing the infill percent of the 3D printed material. We found that increasing the porosity via millimeter scale voids incorporated into the infill pattern decreased the average effective flexoelectric coefficient relative to the near full-density (100% infill) control samples. This contrasts with other studies that have shown increasing micron scale porosity increases the flexoelectric coefficient. In addition, we measured higher flexoelectric responses for nAl/PVDF than μAl/PVDF as well as for samples printed by the Hyrel 3D SR printer as opposed to the Ender 3 V2 printer. These results indicate that charge generation due to flexoelectricity can be altered by changing parameters such as porosity, particle size of inclusions, or manufacturing method. Smaller voids and fine particles can induce larger strain gradients than larger inhomogeneities, leading to increased flexoelectric coefficients. A competing effect is that more porosity leads to less materials, which can decrease the flexoelectric coefficient.
- 17 November 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (19)
Open AccessThe effect of porosity on flexoelectricity in 3D printed aluminum/polyvinylidene fluoride composites
We investigated the relationship between porosity and flexoelectricity for aluminum (Al)/polyvinylidene fluoride (PVDF) composites. Neat PVDF, composites of micron aluminum (μAl)/PVDF, and composites of nano aluminum (nAl)/PVDF were 3D printed, and the flexoelectric response was measured using a cantilever beam test setup. Voids (up to 72.4 mm3) were incorporated into the samples by decreasing the infill percent of the 3D printed material. We found that increasing the porosity via millimeter scale voids incorporated into the infill pattern decreased the average effective flexoelectric coefficient relative to the near full-density (100% infill) control samples. This contrasts with other studies that have shown increasing micron scale porosity increases the flexoelectric coefficient. In addition, we measured higher flexoelectric responses for nAl/PVDF than μAl/PVDF as well as for samples printed by the Hyrel 3D SR printer as opposed to the Ender 3 V2 printer. These results indicate that charge generation due to flexoelectricity can be altered by changing parameters such as porosity, particle size of inclusions, or manufacturing method. Smaller voids and fine particles can induce larger strain gradients than larger inhomogeneities, leading to increased flexoelectric coefficients. A competing effect is that more porosity leads to less materials, which can decrease the flexoelectric coefficient.
- 29 May 2023
- Published by Elsevier in Combustion and Flame
- Vol. 254
Laser ignition of solid propellants using energetic nAl-PVDF optical sensitizers
- 29 May 2023
- Published by Elsevier in Combustion and Flame
- Vol. 254
Laser ignition of solid propellants using energetic nAl-PVDF optical sensitizers
- 16 July 2022
- Published by Elsevier in Combustion and Flame
- Vol. 244
Photoflash and laser ignition of Al/PVDF films and additively manufactured igniters for solid propellant
- 16 July 2022
- Published by Elsevier in Combustion and Flame
- Vol. 244
Photoflash and laser ignition of Al/PVDF films and additively manufactured igniters for solid propellant